JR Replication One Stator Magnet

[FrapsYou]

dislikes by loser government and oil companies and youtube ( a cock sucker)

[earthninja100]

magnet to travel other way dufus... good work for building your own though!!



[PBonline2009]

i can do that without magnets! =))) aftor's lol!

[loltehinternet]

Get a camera with even less frames per second capture, I think you can make it into Guinness.

[hardhatg69]

you got the rotor doing 300rpm and the stator doing like 2...put a little more effort in or dont even wase ur time..the video i saw it wrk in he had to give it way more push and it took a few trys to get the speed just right

[hardhatg69]

@hardhatg69 besides the only way ive seen it work is with 3 magnets...2 going in there natal direction and one oppisite...if you change the disign it only proves that you like to waste time

[Multikraft1]

u need to do all the steps?!?!

[daenumen]

why are you moving the stator magnet??? just let it spin!!!

[DieTheDeath]

@ greenlivingitup . com it shows how to build a free energy device with magnets

[Vortex826]

you cant spin both clockwise spin one clockwise and the other counter clockwise

[Lavinco]

The rapid spinning causes the large wheel to act as though the magnet is not moving and one solid piece.

This is why when it slows down, there becomes a point when the small wheel recognizes the pulse once again and begins to react.

[rufdawg100]

good job now you need push pull effect NNS SSN so you don't have to use fingers. the wheel has to be a triangular in form, less resistance more air flows on flatter surface

[animalnt]

for an hour you were spinning the magnet in the wrong direction... slowing it down lmao

[SFX81]

Sorry mate, but this will work as long as your input energy remains in system. Putting 1 , 2 or X number of stators around this wheel wont make it perpetual. Only solution is if some how you overcome gravity and friction.

[supermoddavid]

stator must go anticlockwise...

[TradeMarkMercenarys]

@supermoddavid no fucking dumbass... its just supposed to go antiGEARWISE which it did

[usernamen0tfound]

@supermoddavid Anti clockwise xD

Counter Clockwise

[MattBlytheTheOne]

i liked the original setup better!

[Amusedman1]

Try putting two of your bar magnets in the slot on the rotor. and try all configurations again. Your magnets are not as long as the ones in the original device, so your magnetic field configurations are not equivalent. If that doesn't work then get some magnets exactly the size as the one in the original. If you are going to duplicate, then you can't over look any minute detail.

[Amusedman1]

Well, after looking at the original again, I have to alter my first response, Your magnets do look to be of similar length, HOWEVER, a close examination of the original the magnets in the original rotor appear to be colored on one end, and if that means that a specific pole is marked by the color, then he has placed those magnets in a specific pattern, with some north poles pointing toward each other, and visa versa. This is probably critical.

[FreeMagneticEnergy]

The armature magnets need a stationary (non-moving) stator, as to have something to push against. Give what I am saying a little thought.

Nice engineering by the way.

[FreeMagneticEnergy]

Lock your stator down.

[pepe1garrapata]

need to be sincronize w a timming belt

[jamanz27]

you were spinning the magnet the wrong way

[fresshness2001]

I applaud the fact that you are checking this out for yourself! KUDOS my friend.

If everybody checked more things out for themselves, we wouldn't be in this deep mess.

[thecosmicshift]

shouldn't the magnet be attached to the main wheel by gears so they move in unison?

[reeldeelpeel]

that kind of eliminates the whole point.

[matthewsolis247]

very good, we are learning!

[MnKndsDoom]

In order for a Perpetual motion machine to exist (esp. one that generates more output energy), you will need to fly to GOD to get the machine. Perpetual motion is a zero-point state resulting in a net output of ZERO. Energy loss in any active system is inevitable. Maintenance of such a machine is inevitable. However, Semi-PMMs are possible. You'll just need to lube often, and replace the weakened parts over time (magnets, one-way bearings, axles, etc..), and things will be good!

[AdminOnDuty]

Perpetual and Eternal are different terms. There is an acoustically isolated bell that has been ringing since the 1800's in a museum. It was fabricated to prove Newtons theories of motion true. Since there is nothing to stop it from ringing it will continue to do so perpetually. ;-)

[Exoskull969]

ya its like a car

[t3ch4]

I thought he spun on of the magnet in the opposite direction.

[AdminOnDuty]

LOL, at 46 seconds it was AGW and you stopped the rotor! Bummer

[offyam]

HAHAHA!! So true.. :/

Kudos to you, JRrep, for going above and beyond. Try spinning the magnets really fast! Also try spinning them COUNTER-clockwise! (2 separate experiments) Good luck.

[Greenpeace82]

when the system is fast, the little one stands still, after speeding up the big one, leave the little one stopped, so speed can't go back! : )

where did u have that one, i want one.

[shubus]

stator magnets appear to be too small for the size wheel you have. Friction is too high.

[Nentin0]

JR your stator's seem way to tight. when you flick it with your finger it should spin for 4 to 6 sec before stoping

[DigitalVG]

Kudos to you for testing thoroughly, even if it's improbable the thing would work.

Though with no additional info from the person who claimed to have a 'working' one, it's seeming unlikely it worked at all.

Or perhaps it worked only because of an environmental concern. Note his fluoro lights flickered. Perhaps there was an extension cord nearby and the 60hz cycle was a contributing factor.

Though, most likely just a hoax.

[xxharddrivexx]

If the magnet are the same strangth your wasten your time use your head and the fact that you are not doing the math the key points are key /GO ONE HOLE AWAY FROM EACH magnet BUT KEEP THEM IN LINE AND MAKE SURE THE OTHER magnet ARE ABIT STRONGER AND HAVE MORE OUTER magnet AND SLOWEL MOVE THEM OFF

AND YOU WILL SEE IT GO FASTER

[phoenixblazestorm]

how about using 23 fixed magnets and 5 stator magnets, just a thought..

[energyscience]

how much did it cost u to build it dude, imean the whole set?

[JRreplication]

I have tried all sorts of combinations off the video. 1, 2, 5, etc.

I think it is a hoax.

[wangchi623]

@JRreplication Umm dude... In the video by alsetalokin. He definitely uses 3 magnets. two slightly larger magnets, and one smaller magnet. the center wheel is spun clockwise and the other two (larger) magnets spun Counter Clockwise also, and last he spins the smaller stator magnet the same direction as the central wheel, and it eventually syncs up with the central wheel causing some sort of acceleration.

I'm still unsure, but if you're gonna replicate it at least do a good job

[phoenixblazestorm]

try 5 stator magnets dude , that shud do it

[Danster82]

Just by the way it moves and spins it doesnt seem quite the same it seems to spin more fluidly where as the orignal seems more bumpy if that makes sense.

[Danster82]

I think there has to be another component to the orignal. Intuitively it doesnt make sense that a perfectly symetrycal arrangment would work, there must be one component that has to be out of sync somehow.

[flyingmonkey350]

Danster is right your missing a component you idiot. Did you not add a battery and motor. What a moron. If your gonna try to disprove perpetual motion try to stay true to the original. And your probably using the wrong lighting. Perpetual motion requires low light to function properly.

[flagtube]

NO. You spin it the wrong way. Example: BIG wheel clockwise, little counter-clockwise. Spin the little magnet very quickly.

[JavaLessons]

Nope, AGW is both the same way around.

[AutogenicMotor]

you see how you use your whole arm to spin up the rotor? Use your whole arm to spin up that stator too, that little finger-only flip won't do it. When you spin the rotor, and the stator is spinning naturally GW with the rotor, watch the speed, that is the same speed you need for AGW. Maybe your bearings aren't free enough. Have fun!

[KungFuBlitzKrieg]

You could use a string to wrap around the stator mag and pull it hard like starting up a gyroscope. That would get the speed up nicely.

[loocian]

awsome