The procedure shown in the video is the one published by Spectrum. I followed those to the letter. The OrangeRx R610 begin the rapid flash when power applied but would not respond when DX5e transmitter was turned on. It did not stop blinking rapidly or blink slowly; and never had a steady glow state (bound). Pls. note: This is w/Spectrum DX5e transmitter. I would like confirmation that the OrangeRx R610 receiver and the DX5e transmitter are compatible - and if so, how to achieve a bind.
I lost my factory bind in the rebuild of an Aert Tech P-51 Mustang foamie with the E-Fly 2.4ghz radio. Using your tutorial, I was able to re-bind and now working perfectly. Props, and thanks again!
@eastcoast78 If anyone here needs help with any technical questions about JR/spectrum please feel free to message me. i can help with binding issues , range on receivers , programing etc. only JR and spectrum please message me. =)
excellent walk through
stimulater7 2 weeks ago
The DX5E is DSM2 protocol, as is the R610 so there should be no problem.
Try adjusting the distance between the two when binding...if its too close it could swamp the rx.
gcshawkey 1 month ago
The procedure shown in the video is the one published by Spectrum. I followed those to the letter. The OrangeRx R610 begin the rapid flash when power applied but would not respond when DX5e transmitter was turned on. It did not stop blinking rapidly or blink slowly; and never had a steady glow state (bound). Pls. note: This is w/Spectrum DX5e transmitter. I would like confirmation that the OrangeRx R610 receiver and the DX5e transmitter are compatible - and if so, how to achieve a bind.
rpw0 2 months ago
Hello. My light on my receiver does not enter bind mode when i attach the bind plug.. it stays solid whatever I do. whats wrong?
zyxelina 4 months ago
@zyxelina
Perhaps the Rx is faulty?
gcshawkey 1 month ago
Also, make sure your battery plug is "the right way up"
gcshawkey 7 months ago
the bind plug must be inserted into the batt bind socket only.
it wont work in any other socket.
Also, if you are using a switch harness, it must be a proper 3 wire Jr / Spektrum harness
gcshawkey 7 months ago
The spectrum rx doesn't flash when I plug it in! What is going wrong?
guynexdoor 7 months ago
THANK YOU SIR! Greetings from USA.
I lost my factory bind in the rebuild of an Aert Tech P-51 Mustang foamie with the E-Fly 2.4ghz radio. Using your tutorial, I was able to re-bind and now working perfectly. Props, and thanks again!
tazztt1 8 months ago
Very helpful for me many thanks :-)
karlelvidge 9 months ago
glad you found it useful.
gcshawkey 9 months ago
very helpful mate.cheers
gubber123456 9 months ago
Just to get it bound initially, it doesnt matter really.
gcshawkey 1 year ago
after its bind'ed, i thought always took the Bind plug out.then powered down RX and then radio.
Take out bind plug.,Turn on TX,then power RX? It always works for me!!!
Or is it wrong? Didn't think you could shut down your radio while power is still on the RX? .
O r does it matter when you in bind mode?
eastcoast78 1 year ago
This has been flagged as spam show
@eastcoast78 If anyone here needs help with any technical questions about JR/spectrum please feel free to message me. i can help with binding issues , range on receivers , programing etc. only JR and spectrum please message me. =)
F35JSF1 1 year ago
This is better than the Spektrum manual
FrostbiteUK 1 year ago
@FrostbiteUK
Cheers Allan :-)
gcshawkey 1 year ago