@sokerismylife I can do all this shit and more to these controllers point was the vid was a waste of fucking time because he doesn't actually show how to DO shit so YOU can go choke on a DICK u lil cock monger!!
Hey Crazeyse8 most likely what is wrong (and I'm just guessing I'm no expert) is that you didnt add a switch. The thing you have to realize about soldering the wires to the board is that they have to have switch to break the flow of the power or even when the controller is off it will constantly drain power from the battery. It's like taking a small light bulb or led and attaching it to a battery there is no on or off switch the only way you can shut it off is by disconnecting it
this one is harder @ 1:48 do you see those 2 little solder points on the bottom right , if you do the left one is positive and the right one is negative . just tellin ya so its easier on you. let me know if it works for you. :)
how do you take out the 4 original leds from the top of the controller where the controller number is. By the way great video i final know how to do the mod after searching for along time
using a 3/16t drill bit i enlarged the hole where the ps button is....the led i got fit perfectly. used file to shorten up led. his wiring diagram and boom i had a modded ps controller
@oilfield666 are you sure you put, negative and positive in the right places, was your controller on, it should have worked right away, let me know if you need any assistance
@DmoneyS2K001 i tryed to solder my wire in the tp12 and kinda messed up so i just desolder it now my controller wont turn on did i fry it theres no damage at all on the bored but now it wont turn on
hey what do you meen at 1;23 theres no where there where you can hook up and led like i turned on the controller and just held an led on it and nothing happened
@jaguars004 are you sure you put, negative and positive in the right places, was your controller on, it should have worked right away, let me know if you need any assistance
i got everything set up but i do not understand if we have to put the led into the hole that i made in the black thing of the pause and back button please response explaning that? thank you
Ya, you have to position the LED and fit it up inside of it, that way it obstruct the function. hope this helps, let me know if you need any more help
@DmoneyS2K001 im currently installed the led in my newest controller. tp12 is in yet a different location in the top right of the bord...the controller i modded lastnite had it in a different location as in your video. it was about half inch to the right in a cluster of 3. also the reset button is of a different kind
@DmoneyS2K001 the housing i just found was a little different. the peice inbetween the l1 and l2 (r1 r2) isnt removable (was a pain to line up when assembling my other controller) its part of the back cover. makes it easier for assembling
@sokerismylife I can do all this shit and more to these controllers point was the vid was a waste of fucking time because he doesn't actually show how to DO shit so YOU can go choke on a DICK u lil cock monger!!
OkieBoy87 2 months ago
Ur vid fucking sux!!! What'd u film with a fucking calculator?!! U suck at life u shud just quit!!!
OkieBoy87 2 months ago
@OkieBoy87 who the fuck r u to tell him he sucks? i bet u cant do half of this shit so stfu
sokerismylife 2 months ago
Hey Crazeyse8 most likely what is wrong (and I'm just guessing I'm no expert) is that you didnt add a switch. The thing you have to realize about soldering the wires to the board is that they have to have switch to break the flow of the power or even when the controller is off it will constantly drain power from the battery. It's like taking a small light bulb or led and attaching it to a battery there is no on or off switch the only way you can shut it off is by disconnecting it
MochaTater 2 months ago
thanks helpped alot
N3Fpr0dUcti0ns 5 months ago
How do you take out the original LED's to replace them with the new ones
CMulley 6 months ago
top right of the new controllers
but what leds are you buying can i get from radio shack ?
glues4wood 6 months ago
this one is harder @ 1:48 do you see those 2 little solder points on the bottom right , if you do the left one is positive and the right one is negative . just tellin ya so its easier on you. let me know if it works for you. :)
Nateisback76 11 months ago
dont know if you guys can help me but i did the mod and my LED wont turn off when the controllers off? lol any suggestions to why this may be?
crazeyse8 11 months ago
u dont need a tp12 i just use a flat screw driver and lay i next to the pin and it twists graet.
beverluc 1 year ago
how do you take out the 4 original leds from the top of the controller where the controller number is. By the way great video i final know how to do the mod after searching for along time
theMillionaire1994 1 year ago
@theMillionaire1994 you take your soldering iron and melt the solder on the pos and neg leads then take pliers and gently remove the led.
1993ni 1 year ago
Finally a tutorial thath fits my old sixaxis controller. I´ve notice that this one has the "vibratores" but what the hack, i going to take the risk
PokerLusiada 1 year ago
i found the tp12, its in up almost in the corner on the right side but i was wondering if it still worked the same way eaven tho its up there now..??
MrWiiman123 1 year ago
using a 3/16t drill bit i enlarged the hole where the ps button is....the led i got fit perfectly. used file to shorten up led. his wiring diagram and boom i had a modded ps controller
oilfield666 2 years ago
@oilfield666 are you sure you put, negative and positive in the right places, was your controller on, it should have worked right away, let me know if you need any assistance
DmoneyS2K001 2 years ago
@oilfield666 disregard that message its for jaguars004, sorry about that
DmoneyS2K001 2 years ago
np...thanks for this vid btw..would of never guessed what pin to connect the positive to.
oilfield666 2 years ago
@DmoneyS2K001 i tryed to solder my wire in the tp12 and kinda messed up so i just desolder it now my controller wont turn on did i fry it theres no damage at all on the bored but now it wont turn on
PanCakePB 8 months ago
hey what do you meen at 1;23 theres no where there where you can hook up and led like i turned on the controller and just held an led on it and nothing happened
jaguars004 2 years ago
@jaguars004 are you sure you put, negative and positive in the right places, was your controller on, it should have worked right away, let me know if you need any assistance
DmoneyS2K001 2 years ago
i got everything set up but i do not understand if we have to put the led into the hole that i made in the black thing of the pause and back button please response explaning that? thank you
supersanchez1991 2 years ago
Ya, you have to position the LED and fit it up inside of it, that way it obstruct the function. hope this helps, let me know if you need any more help
DmoneyS2K001 2 years ago
nvm. i found it. mines just in a different place
xTJM451 2 years ago
dude. did they update the ds3, cus i cannot find the tp12
xTJM451 2 years ago
@xTJM451 sorry for the very late reply, they did update the controller, something, a inner, lining update, I read that somewhere in a PS3 mag
DmoneyS2K001 2 years ago
@DmoneyS2K001 im currently installed the led in my newest controller. tp12 is in yet a different location in the top right of the bord...the controller i modded lastnite had it in a different location as in your video. it was about half inch to the right in a cluster of 3. also the reset button is of a different kind
oilfield666 2 years ago
@DmoneyS2K001 the housing i just found was a little different. the peice inbetween the l1 and l2 (r1 r2) isnt removable (was a pain to line up when assembling my other controller) its part of the back cover. makes it easier for assembling
oilfield666 2 years ago