@semion2003 turn down throttle trim, screw in the idle screw 1/4 turn, start engine, pull breake, if it still cuts out repeat untill work, if it dont work or got any other problems pm me, im alwase happy to help
oh and dont full fottle it it will stall cuz its a big engin its got more comprestion and bigger head to worm up so lil revs at a time till its worm then it wont stall :)
well the first thing i see is you need to let it sit and idle for a minute or 2. then to also get it wormed up just drive it around your house. give it just enought gas to get it moving. thats what i did cus i was having that same problem
hey , someone plz help when i try to start my savage X it dosnt start until i give gass it runs entil i use the brake then it shuts off???? any ideas???
return it to base settings or open the idle speed by taking the air filter of and looking at the gap in the carb when there is no throttle and ajust the idle speed on the carb and make the gap bigger but not to big or it will rev very high and accelerate and it will try to run a way
Try putting your truck back to base settings on the carb. Then put it on a block to get the wheels off the ground. Start it and take the glow pulg starter off after about 5 seconds and let you truck warm up for a minute. Then tune it as per hpi video/manual.
thats a tuning problem try puting it on the ground get it moving then retune it
colesgamingandmods 3 months ago
Try holding it up and accelerate slowly
joi2326 3 months ago
what did u do? i have the same problem
rotas5s5 4 months ago
My savage XL shuts down when I pull the braeks
semion2003 4 months ago
@semion2003 you sure your not running it rich because it shutting down under braking is a sign of it being rich
phsycosniper8 4 months ago
@semion2003 turn down throttle trim, screw in the idle screw 1/4 turn, start engine, pull breake, if it still cuts out repeat untill work, if it dont work or got any other problems pm me, im alwase happy to help
elliotwilson07 4 months ago
It is high speed needle man
semion2003 4 months ago
to rich
poo12318 4 months ago
Typical noob
mattyfromlondon 4 months ago
needs to be tuned
savage25guy123 5 months ago
Your running to rich
900impulsed 5 months ago
Adjust the carb, prob not good to leave the glow plug ignitor on to long either...
VR6dubbin97 5 months ago
Let it run for a few mins mine done it and I left it for like 3 mins and It was fine
roryfitzy12 6 months ago
bottom end is to lean......
aasmith3479 8 months ago
oh and dont full fottle it it will stall cuz its a big engin its got more comprestion and bigger head to worm up so lil revs at a time till its worm then it wont stall :)
2008Grime 9 months ago
well the first thing i see is you need to let it sit and idle for a minute or 2. then to also get it wormed up just drive it around your house. give it just enought gas to get it moving. thats what i did cus i was having that same problem
MRMOTORMAN23 9 months ago
@MRMOTORMAN23 hes right it needs to worm up its trying to go nd ur stopping it so it stalls
sit it to idle for about a minite nd put it on somthing so all 4 wheels can run freely and give it a few revs :)
2008Grime 9 months ago
hey , someone plz help when i try to start my savage X it dosnt start until i give gass it runs entil i use the brake then it shuts off???? any ideas???
tollakt 10 months ago
@tollakt your problem is in linkage
braco222 10 months ago
Put it on the ground instead of not letting the wheels spin it might not stall then also way to rich
08JRX 11 months ago
my diagnosis: too rich, idle too high and too noob
rafa37523 1 year ago
return it to base settings or open the idle speed by taking the air filter of and looking at the gap in the carb when there is no throttle and ajust the idle speed on the carb and make the gap bigger but not to big or it will rev very high and accelerate and it will try to run a way
louis123killer 1 year ago
bad tuning and take ur glow ignitor out unless you want to burn out ur glow plug
DJACE1231 1 year ago
zu wenig sprit
itzek88 1 year ago
way too rich lean it out a bit.
oliver47585 1 year ago
Maybe the motor is to cold. Try To let it run for half a minute and sligtly increase the speed
MaxBeejax 1 year ago
Try putting your truck back to base settings on the carb. Then put it on a block to get the wheels off the ground. Start it and take the glow pulg starter off after about 5 seconds and let you truck warm up for a minute. Then tune it as per hpi video/manual.
philpowell74 1 year ago
just tune it
rctruckmaster 1 year ago
Your engine is way to rich. Turn the high speed needle to the right or clockwise to lean it out.
gravediggerfan93 2 years ago