alcoolaid's 07 STI 0-120

[11miksti]

dont pay attention to rpm. memorize mph for each gear. atleast for 1st to 2nd change. from there get your flat foot shift 2-3 -4- ... get your fukn car tuned! my old 07 stage 2 catless invidia dp was makin 340 by 2500rpm! world of a difference. If you live in the Los Angeles area go to a place in santa clarita Yimi Sport tuning. talk to Paul Leung, and tell him " The White Mexican" or " enchilada MIke" sent you.

[DeekoWeeko]

It was early to change into 2nd gear! you killed that!

Nice video... keep it up!

[Subi06STi]

Are you running stock block or what do you have?

[brandontoscano]

How much hp and torque can a stock sti block handle?

[scoobyjdmd]

Hey man, its scoobyjd from nasioc. Do you have any head work done? And where are you located to get 94, we only have 93 in my area.

[alcoolaid]

@scoobyjdmd i have port and polished heads, valve springs, kelford 276/272 cams, ferrea valves +1mm valves.

but this video was done on stock heads

[scoobyjdmd]

@alcoolaid Those are some really nice numbers for no head work!

[ricecakes13]

@scoobyjdmd chevron sells 94

[canthony1019]

Good idea on not pushing it too hard on stock axles.. i learned the hard way in my 626 rwhp 325i last summer.. built it up and didn't push it hard but one time after the dyno and bent one cv axle, shattered the joint, and bent my main axle on launch..

[silvergate3909]

strong car. good work mate.

[boostwrx]

It sounds like your wastegate spring is too weak, try a stiffer one

[kyleisreallycool]

you neeed 2 step

[alcoolaid]

@kyleisreallycool i have it. see other videos

[brentwiththewrx]

Oh I take that back then, throw some GSC S2's in the mix and that'll bring it up for sure. What's done to your bottom end?

[alcoolaid]

@brentwiththewrx i put in kelford 276/272 cams about a year ago now.

bottom end is 99.75mm cp pistons, carillo rods, calico coated acl race bearings, stock crank, balanced, etc..

[brentwiththewrx]

Very nice car but where's your torque man? 444 seems low on a 2.5L at 511 whp.

[alcoolaid]

@brentwiththewrx seems pretty reasonable for me on stock heads + cams

[WrxStiRwd]

yummy , its a 2.5L ?

[twobimmers]

eww equal-lengths....

[FaSTigris]

Really sounds like EVO :))) Running EL headers ?

[xADAMxSTix]

Launching at 6,000rpm? Damn dude, I launch at ~4200 in my stock turbo STi and I think I could get off the line faster than you, don't launch so high up.

[alcoolaid]

@xADAMxSTix

your turbo makes peak torque way down low since the stock turbo is tiny. if i try launching at 4200 i'm just gonna bog. my peak torque is near 5500rpm

[xADAMxSTix]

@alcoolaid Yeah I didn't think about that, fuckin' nuts car though, I checked all your videos, shit's beautiful man.

[mbdulka]

@xADAMxSTix 4200 is too low, even for stock turbo. I launch at 5500 with stock turbo ... vrrrrrrrrrm!

[sujak27]

@xADAMxSTix agreed with mbdulka and alcoolaid, I launch at 5500rpms on my stock turbo and i pull 1.6x 60 foots all day long, with slips to prove

[MrGTR1988]

so its like 600 HP on engine ?

[valiosubaru]

sounds like EVO :D

[murproject]

I have same problems in launcing. Stock axles and the fear of breaking them. I am using 225 40 18 in wheels and tire. Do you use 9x18 or what else ?

[mbdulka]

@murproject As long as you don't clutch dump, your car will be fine ... your clutch won't like you much, but otherwise, STis are pretty damn tough.

BTW, sick car Alcoolaid ... I will probably go BW turbo as well. Which one you running?  83-75, 88-75, 91-79?

[saudikid]

yaa!! best AWD fuckign car ever made after skyline. man i wish i could just sit in it and feel what a car with 500+ HP feels like, most i have sat in is 140 HP integra LOL i aint rich