PMDG 737NGX Cold and Dark to Taxi. (Tutorial)

[SparrowVasco]

I like this video. I noticed you (sometimes) can "travel" to the sides to get a better view on the upper panel (like at 04.56). How do you do it? Thanks for your help. Hugs :)

[dsadwarf]

What is the music?

[Leffe49]

No it´s not.

[afgrocks123]

Hey, do you have any idea how to fly a waypoint or airport DIRECT, without having it planned... and where is the bearing of the runway etc.... located on the panels? plz reply :)

[MuratAyata]

sn cercevikezdo i landigimdan beri iniste gozuken touchdown da z rubbe fricion kayboldu bunun ezca ile ilgisi olabilirmi tesekkurler

[TheJack4000111]

Pitty you insert the music. It makes your video crappy.

[arsenalfeet]

the sound of the music is explaining to my mind what buttons to press ::::: NO...

you need to use a microphone to do this my mane man, no offence but it was confusing and just bad :/

[2008philliesfan]

you dont need to do default cessna anymore. PMDG lets it all be done from fmc

[Timsalt3100]

@2008philliesfan I am a bit suprised myself I always do it from Panel state in the FMC

[BobbyJEL101]

Silly you. :) I'm sure you have been told this before, but you just goto the fmc (while everything is still started) Pmdg setup, load panel state. Cld and drk :D

[ytaca56]

One word: PERFECT, thk.

[fdx183]

The music was great, but personally for tutorial video's I don't like music in the background. There should be a voice or at least descriptions of each step taken in the "correct" order from dark and cold to engine start up..If this was for pure entertainment, nice job.

[Leffe49]

Nice video!

I have to say though, that you didn´t follow the normal checklist and also you shall not dial in 220 in your speed window. You are supposed to dial in your V2 which was 154.

After acc height, you can dial in 220 and then go from there.



[cercevik]

@Leffe49 You are right. I have easily done ;-) Thank you

[MrFsx100]

@Leffe49 actually, its v2 +15

[tcnrdl]

adamım çok iyisin taşaklarından öpüyorum

yalnız fmc motorları çalıştırmadan önce kuruluyor diye biliyorum

[cercevik]

@tcnrdl Bildiğin doğrudur adamım ben sadece çalışrırmayı göseterecektim sonradan hadi bağri proğramlamayıda hazırlayım demiştim. Hatta pushbackta motor çalıştırılmadan önce yapılıyor genellikle. Apu den sonra FMC hazılaması daha sonra Motoru çalıştırmak için checkl ettikten sonra Pushback soruyorsun groundan.

[tcnrdl]

@cercevik ok dostum :) güzel videoların devamını bekleriz :)

[Mateusfsxrc3phun]

can you please tell me what are your pc configurations?

[bartjko]

Thanks a lot Cercevik! Great video, I am now making a list of steps you perform to have everything listed! Could you tell me what viewing software you use to perform these incredible smooth view changes? Im guessing that its not TRACKIR, do you have custom views set? please contact me about that! thanks again for this video!

[cercevik]

@bartjko I use EZDOk camera from fligh1, and I've created a shortcuts on keyboard for every camera pos.

[bartjko]

@cercevik thank you!

[cenkcdemir]

elinize sağlık çok güzel bir çalışma. keşke sözlü veya yazılı anlatımı da ekleseniz.

[anilumutozlu]

Yararli bir video, kamera programi nedir sn. cercevik? Saygilar.

[cercevik]

@anilumutozlu EZDOK camera addon

[bobe621]

Merci, Thanks for your help

[yigitciftci]

bastan sona yaptiginiz adimlari bilgilere yazsaydiniz..

[cercevik]

@yigitciftci Yazacaktım ama konuyu taşırsınız ve kaybedersiniz diye korktum, anladınız siz onu ucuyorum(dot)com dan ;-))