@timma100AR if you really plan on doing this, i'd recommend you to build a little led-driver module that uses an audio signal input to control your led array(s).. the functionality of this quick'n dirty setup is very limited
NEVER, NEVER, NEVER connect anything other than speakers to your amp. That is the WORST thing you could possibly do. An amp expects a resistive load. When you put diodes (Light Emitting Diodes) across the outputs, you're asking for trouble. Not only can the LEDs burn up but they can also short out the amps outputs!!!!
klappt das auch wenn ich 2x 150 Ohm wiederstände parallel schalte ? bzw reichen auch nur ein 150 Ohm widerstand, hab sonst nurnoch 680 Ohm widerstände :S
NEVER, NEVER, NEVER connect anything other than speakers to your amp. That is the WORST thing you could possibly do. Not only can the LEDs burn up but they can also short out the amps outputs!!!!
One method is to use the output of the source - watch?v=uOw_Ynx1tGc
@wast3mytim3 quark, viel einfacher... du kannst die LEDs einfach mit an den Endstufenausgang, quasi parallel zum Sub anschließen... wie viele du in Reihe nimmst, mit welchem Widerstand musste ausprobiern. ( hängt von der Endstufe/Batteie/Subwoofer/LEDs ab...) ich hab normale 5mm LEDs dran, 4 stk Parallel und davor ein ma n 220 Ohm 1/4 W widerstand, funzt perfekt...
hallo, ich spreche klein duetsch, aber, kann dich sprech english mit mir? lol anyways, did you just wire them in series to go off at a certain voltage?
they are wired parallel, with one ~200Ohm resistor in series ( to prevent them from burning at high volumes), i'd recommend a 1/4 W resistor, the smaller 1/8W resistors might geht a little hot at high volumes...
danke schoen. i don't know off the top of my head what the actual voltage is for my subs, considering the fact that it is bouncing around to the music. you think i need an oscilloscope to show that? any other way?
ich hab es os gemacht ! ABER ich hab ne 20 rms mini enstufe besorgt und die ganze led dran gezwickt DAS IS ECHT GEIL jetzt muss ich net so auf drehn ich dreh einfach den regler von der miniendstufe hoch damit die dinger an gehn ! is echt geil musst de auch machen nachts bei mir im zimmer is jetzt ents chillig geworden ! haha leise musik nd die leds ;)
hab ich auch schon drüber nachgedacht, aber nya.. ich hab noch ne lichtorgel unter meinem schreibtisch.. mit 3 150 W farbigen strahlern.. da kann ich einfach am regler rumdrehn dann gehn die auch bei leiser musik^^ dan hab ich mir noch aus 54 farbigen LEDs nen led-strip gebaut mit nem RGB controller... wenn die dann noch rumblinken, das geht schon ab... dann noch + selbstgebaute mini "lasershow" ( mit nem 100 mW roten laser) + nebel...und ne shisha :D das is auch durchaus chillig =)
das problem bei LEDs ist, dass sie nicht über die Spannung, sondern über den Strom geregelt werden. d.h. niemals ne LED ohne Widerstand betreiben... bei meinen LEDs waren immer so 470 Ohm widerstände mit bei... so kleine... ham glaub ich 1/8 Watt... nimm 2 davon Parallel (-> R=235 Ohm und 1/4 watt..) das 2er Päckchen hängste in Reihe vor die LEDs (die LEDs parallel aufeinander..) dann kannste ziemlich aufdrehn... sollte nichts passieren.
Going to use this same concept to link it to the external lighting kit on my truck :D
timma100AR 4 months ago
@timma100AR if you really plan on doing this, i'd recommend you to build a little led-driver module that uses an audio signal input to control your led array(s).. the functionality of this quick'n dirty setup is very limited
tryToGetUp 4 months ago
wie heißt das lied?
ElectroMusikBoy 7 months ago
This has been flagged as spam show
NEVER, NEVER, NEVER connect anything other than speakers to your amp. That is the WORST thing you could possibly do. An amp expects a resistive load. When you put diodes (Light Emitting Diodes) across the outputs, you're asking for trouble. Not only can the LEDs burn up but they can also short out the amps outputs!!!!
sparky3489 8 months ago
klappt das auch wenn ich 2x 150 Ohm wiederstände parallel schalte ? bzw reichen auch nur ein 150 Ohm widerstand, hab sonst nurnoch 680 Ohm widerstände :S
Snipa51 8 months ago
@Snipa51
klappt, habs mit ~400Ohm zum laufen gebracht, muss aber sehr lautstellen :)
Snipa51 8 months ago
Has any body sow this evjlight.com lighting mehod ?
profEVJ 10 months ago
Your youtube channel looks great... Keep up the high quality videos...
P90xFitnessExpert 10 months ago
How is the subwoofer now? the vid is posted over 2 year ago..
Can you do a tutorial for this vid?
monkey8113 10 months ago
Look SH17 2 me
hateeb786 10 months ago
This has been flagged as spam show
NEVER, NEVER, NEVER connect anything other than speakers to your amp. That is the WORST thing you could possibly do. Not only can the LEDs burn up but they can also short out the amps outputs!!!!
One method is to use the output of the source - watch?v=uOw_Ynx1tGc
sparky3489 11 months ago
very cool, it looks great!
AggroNRG 1 year ago
how do u connected to and fix to? any tutorial?
qAyyUm 1 year ago
du musst mal ein totorial machen dazu, wie man leds einbaut
danielxharder 1 year ago
hi did you just connected those LED's on to the wire that connects the speaker to the amplifier
g30rge93 1 year ago
@g30rge93
please read the other comments to find out, how this was done
tryToGetUp 1 year ago
@g30rge93 speaker
TREXTINO1 1 year ago
@g30rge93
no, no no no! Connect those LEDs via evjLight controller and get much more interesting effect!
profEVJ 9 months ago
Hello,
thats very nice!
but what is that last song? plz thx alot for the help!
warpp2 1 year ago
Hey man, that's very well done. Mind telling us how you wired the lights to pulse with the subwoofer?
Wubnig 1 year ago
eine frage
ich hab ein 5.1 anlage von logiteh zu hause für pc
kann ich bei der subwoofer auch die leds einbauen und wie mach ich das am besten ich hab kein plan xD
ComicDeFun 1 year ago
its nice
forkane69 1 year ago
Tell me how u did that please
51235465789 1 year ago
wie hastn des gemacht? mit nem LM3915? und dann ne frequenzweiche davor?
wast3mytim3 1 year ago
@wast3mytim3 quark, viel einfacher... du kannst die LEDs einfach mit an den Endstufenausgang, quasi parallel zum Sub anschließen... wie viele du in Reihe nimmst, mit welchem Widerstand musste ausprobiern. ( hängt von der Endstufe/Batteie/Subwoofer/LEDs ab...) ich hab normale 5mm LEDs dran, 4 stk Parallel und davor ein ma n 220 Ohm 1/4 W widerstand, funzt perfekt...
tryToGetUp 1 year ago
@tryToGetUp
pfuschen tu'mer hier ned =D ..ne aber wenn das so gut geht, dann werd ich das bei meiner z5500 machen :) danke
wast3mytim3 1 year ago
hallo, ich spreche klein duetsch, aber, kann dich sprech english mit mir? lol anyways, did you just wire them in series to go off at a certain voltage?
happymerc 1 year ago
@happymerc
they are wired parallel, with one ~200Ohm resistor in series ( to prevent them from burning at high volumes), i'd recommend a 1/4 W resistor, the smaller 1/8W resistors might geht a little hot at high volumes...
tryToGetUp 1 year ago
@tryToGetUp
danke schoen. i don't know off the top of my head what the actual voltage is for my subs, considering the fact that it is bouncing around to the music. you think i need an oscilloscope to show that? any other way?
thanks again,
HappyMerc
happymerc 1 year ago
34DENOG34 2 years ago
@34DENOG34
hab ich auch schon drüber nachgedacht, aber nya.. ich hab noch ne lichtorgel unter meinem schreibtisch.. mit 3 150 W farbigen strahlern.. da kann ich einfach am regler rumdrehn dann gehn die auch bei leiser musik^^ dan hab ich mir noch aus 54 farbigen LEDs nen led-strip gebaut mit nem RGB controller... wenn die dann noch rumblinken, das geht schon ab... dann noch + selbstgebaute mini "lasershow" ( mit nem 100 mW roten laser) + nebel...und ne shisha :D das is auch durchaus chillig =)
tryToGetUp 2 years ago
danke ! man
kann ich sie dann auch bei leiser musik sehn !
weil normaler weise um so lauter man macht um so häller wwerden sie oder nicht ?
34DENOG34 2 years ago
naja du musst schon bissl weiter dann aufdrehn als vorher, bis sie leuchten, dafür rauchen sie dir aber nicht nach 5 minuten ab
tryToGetUp 2 years ago
und wie heisst der track ?? 0:48
34DENOG34 2 years ago
das is Black Eyed Peas - Simple Little Melody
tryToGetUp 2 years ago
willst de ma wissen wie oft bei mir die dinger durchbrennen ??
ich verbinde die led´s miteinander ! dan ran an den sub damit !
und wen ich aufdreh brennen sie durch !
brauch ich irgendein transformator oder so damit die net durchbrennen ! ausserdem
brenne die net wenn ichs leise habe
also man muss schon bisl aufdrehn damit se aufgehn !
und dann brennen sie irgenwann ununterbrochen ach ka sag
mir einfach wie du es bitte gemacht hast !
danke !
34DENOG34 2 years ago
das problem bei LEDs ist, dass sie nicht über die Spannung, sondern über den Strom geregelt werden. d.h. niemals ne LED ohne Widerstand betreiben... bei meinen LEDs waren immer so 470 Ohm widerstände mit bei... so kleine... ham glaub ich 1/8 Watt... nimm 2 davon Parallel (-> R=235 Ohm und 1/4 watt..) das 2er Päckchen hängste in Reihe vor die LEDs (die LEDs parallel aufeinander..) dann kannste ziemlich aufdrehn... sollte nichts passieren.
tryToGetUp 2 years ago
thats sick. how did u do it??
Gregor2004ua 2 years ago