One of the nicest builds I have seen but i think I may recognize a small problem, your jet is way to far past the air intake slide it out until the jet is just even with or behind the internal port I think (hope) you will find you don't need forced air, also with your propane working pressure your tank valve may freeze up! so your working pressure might be able to be reduced if you try this.
I havent tested the burner actually. Ill be honest i had to put that project to the side for now. Im considering adding a blow dryer or some sort of forced air system to increase volume/heat. But it seems pretty damn hot right now. Iff you add a second bottle all it will do is add more available propane not really increase volume. The regulator controls that. Adding more oxygene to the source of the flame will increase the burn intensity and heat though.
cool burner and great explanation. just one question, to add more heat would it be better to connect a second propane tank (to increase pressure/flow) or set up a second burner?
Thanks for the view and the details. I might be a bit uncomfortable with lighting it outside and then placing into tube, with the flames coming out the slide gate as shown. Why not light with the tip in place?
While the air through the concentric pipes means that you cannot have control, it has more than it needs-- and it appears that you could add a blower easily?
very well spoken rite through the prosses bud,10/10
theres allot of different types of burners getting around on here,but not many take the time to show how its made and what its made of again 10/10 thanks for your time and info :)
Wel thanks for the advice. I may want to shorten the burner tube but i left it long because i can always shorten it but i cant lengthen it as easily. Also, i used scrap i had in the shop so the sizes and material were not my top pick but free and abundant.
you can light the burner by holding a lighter in front of the burner tube, your orfice should be setting about even with the front of you aid inlet, also use a smaller size pipe for a orfice/nozzle pipe it dosen't have to be that big, and your burner tube is way too long, and its way up inside the tube, shorten the tube and put a flare on the outside for using out of a forge or furnace.
One of the nicest builds I have seen but i think I may recognize a small problem, your jet is way to far past the air intake slide it out until the jet is just even with or behind the internal port I think (hope) you will find you don't need forced air, also with your propane working pressure your tank valve may freeze up! so your working pressure might be able to be reduced if you try this.
chillybill957 3 days ago
Nice work. Did you do the welding yourself?
user196489 4 weeks ago
I havent tested the burner actually. Ill be honest i had to put that project to the side for now. Im considering adding a blow dryer or some sort of forced air system to increase volume/heat. But it seems pretty damn hot right now. Iff you add a second bottle all it will do is add more available propane not really increase volume. The regulator controls that. Adding more oxygene to the source of the flame will increase the burn intensity and heat though.
nickrendo 1 month ago
You may have saved me $50. I'll have to modify my burner ASAP....
spinafire 1 month ago
awesome setup, 2 questions, how fast do you go through your gas per bottle? & have you tested to see what temp your flame gets at full flow?
Jamac007 1 month ago
cool burner and great explanation. just one question, to add more heat would it be better to connect a second propane tank (to increase pressure/flow) or set up a second burner?
rincewind93 3 months ago
Thanks for the view and the details. I might be a bit uncomfortable with lighting it outside and then placing into tube, with the flames coming out the slide gate as shown. Why not light with the tip in place?
While the air through the concentric pipes means that you cannot have control, it has more than it needs-- and it appears that you could add a blower easily?
art4med 6 months ago
Not simple.
sweetheartK3 7 months ago
Thanks, i also made a forge and working on a custom belt sander as well
nickrendo 9 months ago
very well spoken rite through the prosses bud,10/10
theres allot of different types of burners getting around on here,but not many take the time to show how its made and what its made of again 10/10 thanks for your time and info :)
nosjet1 9 months ago
Wel thanks for the advice. I may want to shorten the burner tube but i left it long because i can always shorten it but i cant lengthen it as easily. Also, i used scrap i had in the shop so the sizes and material were not my top pick but free and abundant.
nickrendo 10 months ago
Does it work if you just light it from the tip?
pyrosimple 1 year ago
you can light the burner by holding a lighter in front of the burner tube, your orfice should be setting about even with the front of you aid inlet, also use a smaller size pipe for a orfice/nozzle pipe it dosen't have to be that big, and your burner tube is way too long, and its way up inside the tube, shorten the tube and put a flare on the outside for using out of a forge or furnace.
SUPERDAVE257 1 year ago
You do know the stainless steel melt Before Steel :D dont you
mrsyafi 1 year ago
I like the design. Thing about one of thoes small tanks, you will have a hard time maintaining that pressure.
jameasun 1 year ago