One6 2000 Civic CX B18C5 Engine Swap Part 2 of 3

[yeska420ne]

clean swap vid best 1 i seen so far.

[JendrusZbojnik]

for wat motor did they order this exhaust?

[Paintballin4respect]

after they put all this stuff if you change the camshafts, valves and pistons would yu be aable to turbo this engine?

[elbellaco86]

hey i have a question i have a 97 civic and i did a swap into a jdm gsr b18c. i want to know wat kind of mounts could i use?

[sctflasher379]

what do you mean a stage 3 is overkill??

[peppersnsmartpots]

My b18c5 destroyed my factory db2 motor mounts. I have a feeling if this motor runs strong it will destroy those Honda mounts. And a stage 3 clutch is overkill. The factory b18c5 clutch will chirp tires into 3rd gear. Stage 1 Exedy FTW! It has a torque capacity 20% above the factory unit. You cannot make 20% increase in tourque NA.

[red666A]

Dope and check out my civic project...

[DrMu5tCh3at2W1n]

my mechanic Jose doesn't look like any of these guys....

[bigtime17ify]

dhdf

[bawww13]

I have a d16y7 in a 1998 lx civic I have been looking to buy a B16A II online how hard is this swap and whats it take to get it done please help!

[67mustangreg]

working on cars is cool, but these guys seem like doushbags and the music makes my ears bleed

[keffysnep]

how much does a job like this cost to do? ive just bought a 98 civic coupe and want to replace its shitty 1.6 with a type r engine? can n e 1 help me out with pricing, p.s. im in the u.k. but i can estimate the conversion into £ from $

[Blaze0303]

If by type r motor, you mean a vtec engine then you're looking at around 2 grand for a decent b16b plus installation, then another grand for a decent set of headers... add a few grand for some nice spoon parts, tidy the bay and get it looking good and you're away ;)

[keffysnep]

haha i havent got that type of cash at the moment n if i did i might as well jus buy the car already done lol or something else thats fast coz id have to put money into the brakes, wheels, suspension, exhaust manifold etc jus buy a skyline or sumfin lol

[vahn2g4]

Where are you guys located? Does anyone know any shops on the east coast (tri-state) where I can get something like this done?

[trabe1]

"hey can a non vtec motor work on a civic wit a vtec motor??? and not ave any problems "

huh?

[spoontuner]

all you need is a vtec wire harness and ecu.

[joelmoyses]

hey can a non vtec motor work on a civic wit a vtec motor??? and not ave any problems

[DJphobia]

...this is the equivalent to asking " If I buy an apple, can I still eat my pear and not have any problems?"

[josemjr55]

One6 is great, I was there to get a manual tensioner . I convert my 98 prelude sh from auto to manual, mark was there to help me out to get the parts I need. There located at 610 Bennett rd in elk grove IL.

[joescivic]

man, i wish the people who swapped my k20 would have gotten new parts for it just incase they were to go bad. they used the original rsx axles that are rusty, and even gave me a dirty motor without even cleaning it. id like to have a new clutch like they did in this video. and they never even gave me a new primary wideband o2 sensor. WTF?? i have this gay CEL all the time.

[area220sucks]

damn u guys are lucky.. i'm still looking for an engine swap shop that will hire me.ritenow i'm doing backyard specials :(

[WRXSTi16]

better to be self employed, dont gotta deal with Bullshit bosses.

[area220sucks]

wut about the weekly check is it good though?

[WRXSTi16]

psh why get paid weekly when you cab get paid right when you're done with the job

[area220sucks]

that's what i'm doing right now easy money in my pocket feels good

[jordanturbo1986]

stage 3 clutch on oem itr lun, bit excessive i think, if the motor was blown woulf be diff story

[NEKNINE]

I dont understand why they used a stage 3 clutch on a NA motor its not putting out that high of numbers. Unless hes planning to boost it later down the road it makes no sense to me. But I like the swap, I'm sure it made that hatch pretty quick. Hondas are great.

[lindseyhunt1090]

wow im suprised an actaul shop would put a ctr crank pully on a itr. thats bad news. u need a harmonic balancer.

[businessbmw]

i have a question but only answer if you really know!!

i want to swap the 5.4l ford expedition to put in a ford ranger 2.3l 4 cylinder engine, can i do that? The expedition is a RWD.

[nusair2]

yea but make sure u get custom made motor mounts

[back720sk8er]

hey i have a jdm b18c in my 2000 ex i think due to my mounts when im on it it shakes alot like the whole car and the axles pop what mounts should i get where from and how much oh right now the mounts i have are the 2 sides and back should i get the front tranny stock mount?

[UnforgivingGod]

Okay Im a lil bit lost here the car and the engine are OBD2 so why are they converting to OBD1? And actually the car is street legal depending on your state not cali though =[

[ayo2yayo]

BUMP!

[silentbob831]

Too bad the car won't be street legal with that OBD-1 conversion.

[windsurf2228]

very sexy engine you boys should get some birds helping you out will make the vid look more nicer

[inagod]

great work guys,make it look factory,no hacks,missing bolts,hardware,using old belt,clutch etc.very nice swap

[racer46]

hey i saw the FAskates poster i go there all the time.

are you guys next door.

[ceetboy]

much love to white people around the states who do care about import and representing honda! nice hip hop too.

[B18BEG6ick]

nice! these guys aren't that far away from me!

[driftunit27]

This video is sick! Love the Editing Too!

[gurlyracerzz]

even white guys throw away their big block for a typeR. imports rule!

[nb1001]

nice