i am ready to put my blade behind the rear tire of my truck and run it over out of frustration im going to try your tip i hope it works because if it doesn't its getting run over or my other hobby is shooting and it would make a good moving target thanks
I must admit, I can fully understand ur frustration, do what I did and stamp on the thing until it cannot be repaired. No more frustration for me any more ;o)
with all the mods that are needed to get this blade 400 up to par, and it no longer becomes a good deal....new servos a must....cnc upgrade....man oh man, but the hobby shops love to try and push and sell this one.
@ilikecheetos12 yep your rite. i just got a used blade400 from a freind and it needed some parts. so i went to willis hobby shop and thay tryed to sell me everything i didnt need. i was told it had a bent main shaft so i replaced it and found out it was not bent. but the servos are a must upgrade !!!!
pick up the CNC wash out arms.....you can tighten those suckers down as snug as theyll goo without any binding....deff a worth while upgrade....the metal head grips will make a world of diff with your CF blades as well
This is a great tip! I learnt the hard way when I thought I was doing the right thing by going over my B400 to tighten everything up! It took me a lot longer to find the problem than it did to find this video, I am sure you will save a lot of people a lot of frustration with this!
Thank you, I no how frustrating it can be looking for reasons of vibration, so when I found my problem I thought it would be helpful to mention it here.
How tight? is it supposed to be loose a bit?
TheBaty 1 year ago
Just got a used 400 with a vibration problem. This sure helped!
RobTapscott 1 year ago
i am ready to put my blade behind the rear tire of my truck and run it over out of frustration im going to try your tip i hope it works because if it doesn't its getting run over or my other hobby is shooting and it would make a good moving target thanks
colk25446 2 years ago
I must admit, I can fully understand ur frustration, do what I did and stamp on the thing until it cannot be repaired. No more frustration for me any more ;o)
r6yamahar1 2 years ago
Thanks for posting a great tip, Helped me not waste time !! Will upgrade to Bluminum soonest. Montana USA
redbr8der 2 years ago
Thanks So Much MATE !!!
Saved me a lot of Hassle !!!
donakaal 2 years ago
with all the mods that are needed to get this blade 400 up to par, and it no longer becomes a good deal....new servos a must....cnc upgrade....man oh man, but the hobby shops love to try and push and sell this one.
ilikecheetos12 3 years ago
@ilikecheetos12 yep your rite. i just got a used blade400 from a freind and it needed some parts. so i went to willis hobby shop and thay tryed to sell me everything i didnt need. i was told it had a bent main shaft so i replaced it and found out it was not bent. but the servos are a must upgrade !!!!
paddywagons104 1 year ago
pick up the CNC wash out arms.....you can tighten those suckers down as snug as theyll goo without any binding....deff a worth while upgrade....the metal head grips will make a world of diff with your CF blades as well
qsecgtyhd 3 years ago
nice find mate ;) not had that prob yet but i will defo keep it in mind ;) 5*
0n3m1s1s0 3 years ago
This is a great tip! I learnt the hard way when I thought I was doing the right thing by going over my B400 to tighten everything up! It took me a lot longer to find the problem than it did to find this video, I am sure you will save a lot of people a lot of frustration with this!
styndal 3 years ago 2
Thank you, I no how frustrating it can be looking for reasons of vibration, so when I found my problem I thought it would be helpful to mention it here.
r6yamahar1 3 years ago
Goot tip thanks
captainuk001 3 years ago 2
Thanks
r6yamahar1 3 years ago