013 hho generator test with water filters design

[LoRider100]

that parallel



[bertulforc1]

Simple test HHO machine is effective or NOT. Park the car, start

engine to normal temperature, run to 1500 rpm and hold it there by

using tools or wedges. Turn ON your favorite HHO machine. Check the

RPM goes up to 1600 or more, it is GOOD. If RPM goes down or the same,

your HHO machine is ineffective, useless, and waste of time, effort

and money. Any seller will pass this test, buy their HHO machine.

(Forget the driving around wasting more gas, or read On Board Computer

Instant MPG).

[NAGGERNUTZ]

@FIZZYH2O - What is the purpose of the bubbler? Does it just act as a check valve? Couldn't you use a check valve from a hospital oxygen hose instead of a cumbersome bubbler? Just asking.

[johnnnyreb51]

Use Solar power (from solar panels) to produce Hydrogen. Then by using a Hydrogen Fuel Cell to produce electrical power, With a by product of water. We can use the power anytime. (Sun to make it, Hydrogen to carry it, The fuel cell to use the power anytime) Any product that we destroy to make power will not work! It will not happen in our life time but, we will run out! "We do not leave the world to our children, We barrow it from them."

[mrtruthify]

@johnnnyreb51

Great comment.

[quitstrike]

Need to install a check valve on each for the "just in case" failure.

[terrystech]

When you are speaking about pressure relief valves remember that the vented gas should always be sent away from the engine or any heat source for that matter. The last thing you want is raw HHO venting under the hood.

[quitstrike]

@terrystech Very true!

[urbex2007]

Interesting, but can you explain how this tells the ECU in the car to inject less petrol/diesel in proportion to the amount of hydrogen being injected?

The car would need this as it would inject the same amount of petrol/diesel before and after this kit was fitted - which means NO saving. This is the one thing people forget, which is why it is a scam to say injecting small amounts of hydrogen somehow causes less fuel to be injected! Sort out the ECU & fuel injection first! It's a con!!!

[komputeruser]

@urbex2007 You don't need to tell the ECU to put in less fuel for the motor. The hydrogen is being burnt with your fuel, and makes the overall process more efficient. You get a lot more power from your motor from the same amount of fuel, at the same rpm, so you do not need put your foot into it so much. Don't think of the hydrogen as a replacement fuel. Think of it like a catalyst, like propane on a diesel engine. And if you think it's a scam, don't buy anything, build it yourself.

[moviejacker]

daisy chaining is the series method. running off a single and tapping off that is the parallel method. high current draw is the series, high voltage draw is the parallel.

[bambinapechocha]

QUISIERA SABER SI YA ESTA A LA VENTA Y CUANTO CUESTA Y PARA QUE TIPO DE CARROS ESTA DISEÑADO

[truthseeka1]

Presentation was cool. Ur HHO is crap. The comments by the other dickheads stupid.

[fuelban]

i got to agree with you this type of relief V/V, is safe, and is the type I am going to use too, The in line sort packed with wire, isn’t so safe in my mind, whilst they stop a spark, and flame from going up the line, they can also act as a flame thrower in the line, being fed Hho it can continue to burn in the pipe { melt down} for plastic pipe users.

Thom in Scotland.

[Hogasofa]

what is the softwere you are using for this please tell.

[themakingofstuff]

what program are you using? please please comment back

[Elevationary]

There is one problem with this design,each one of them are independent,and each will have to be filled independently with water.....so if one runs out,or if one does not have enough gas pressure to release,then you will end up with a miss fire! in one of the cylinder heads in the combustion chamber,i would be going about it differently.....

[GOTJIFF223]

@Elevationary

well correct me if im wrong but he did say that if he did not connect them together it would prevent a total melt down IF it were to occur that would be the reason that there not connected and last he also had said that he want to constantly run cooler and fresh water through these filters and if they were to be all connected as one that COULD cause a heat problem it really depends on the design. just saying :)

[billrbushatutube]

parrall dummy

[rodrick4500]

need to know what software you used to design this picture love to know

[zuseable]

add apop off valve and did you now that dc motors make curent when you spin them all of them do add a diod and there you go my favorite is razor scootor motors and fore elicktrolizer sodium hydroxy or potasium hydroxy both are dangerus . by the way have you looked in to solar wind water steam and otheres i am trying to combined them all . help think big

[b20002003]

google sketch up!!!

[shawn12ization]

thats, a parralel connection ,series would be +- +-+-

[Soldja911247]

Visit freemicrosoftpoint[DOT]com

[zeropointprophet]

i wonder if you can incorparate this with the GEET system that woud be interesting to see

[juggernautxtr]

man i wish you'd people would actually read something before you start trying to make a car run on hydrogen.

this is all come about because of Stan Meyers.

he was not running his car on hho.

hho was merely a fuel to to excite the water injected into the cylinder ie. reinventing the steam engine!

look at the damn injectors he has in his blue prints. fill the tank with water and convert a portion of that into hho while driving and the rest is converted to steam in the cylinder.

[zeropointprophet]

i think meyers was Exploding water instead of burning hho like everyone seems to think

[juggernautxtr]

well the thing is if steam is hot enough it will explode it self.

from what i can tell it is a continual ijection just getting hotter all the time. the steam will seperate and ignite.

and it wouldn't take but 1 mil of water to do it in a 1600 cc bug motor. larger engines may require a tad more.

[zeropointprophet]

i was refuring to high voltage AC used to explode water...are you familiar?

[juggernautxtr]

and you wanna apply AC voltage to an engine block with a 12v battery grounded to it?

[zeropointprophet]

its alittle more complicated then that...if you want to know more search on youtube for "exploding water"

[juggernautxtr]

well thats the whole point of trying to recreate something that someone else did. it's all about finding out whats actually going on.

[tikocorazondemetal]

i found out how to make more efficient the electrolisis, with the exact combination of water and electrolite

[FORDGTFANATIC]

i think the quick release design would only be large and short burst of the gas not the same constant trickle im a total noob here i havent even build my own generator yet but am about to, but thats just my 2 cents on the quick release

[warlocks789]

hey bud , get it together what the hell are u tried to accomplishS ..

[mikemmcmeans]

do you think you could post a link to your sketchup file?

[mikemmcmeans]

its parallel in the video you made

[thealbatross1001]

you can make free electricity as well just type in chris szoloch into a search engine and there will be instructions there, and instructions on a tap water car, all you need is a water tank and then run a positive charge at the top and a negative charge at the bottom and then the hho atoms will come appart, and then run that into the engine, just like lpg, put an lpg conversion on the head and then just get a hydrogen regulator, because hydrogen has a different density to lpg,

[Chewylu103]

your wiring is parallel man not that it matters but that would have went up my *ss sideways if i let that go

[SilentInLoud]

I've tried many water engine systems but so far this is the winner.

blog.aboutceo(dot)com/?topic=w­atercar

[DEFENDtheREPUBLIC]

looks like he is using google sketchup. great program. easy to learn. free download from google.

[whey20010]

what cad program did u use?

[mikemmcmeans]

google sketchup. its free

[420darklotus]

just from a mechanics point of veiw, u gotta make sure that your Pop-off valves are set to a higher p.s.i that your pressure on the fuel outlet side. if the outlet is lower than the valve, you will be losing fuel out that valve. it's like a studor vent in house plumbing, it's only for a burp in the system.

[GiDesignMrktg]

FIZZYH2O id like to know what software you are using to capture screen video

[Banyan23]

I don't know if you mention how many plates per unit you plan to install, however make sure you don't have more than 2 volts per space (Cell) between each plates. That way you'll not have any heating problem. More voltage than that will be wasted in the creation of heat. 1.5 volt is best. You calculate the efficiency of the cell not by the amount of gas it produce but by the MMW (Milliliter, per minute, per Watt)

Have fun!!!!

[GOplayer]

Would you help me understand the apparent contradiction between the direction people seem to think that heat is a waste of energy in the HHO generation process? The contradiction that I refer is the principle that states if the temperature of the element in which ions are moving is rising, the speed at which the ions moving will increase. That tells me that I should get better HHO production since IONS will move faster from + to -. Yes? Please explain. Thanks Z

[Banyan23]

Good question! I'll try to answer it but I'm not a scientist. There is no contradiction, you are right, heat IS suitable to have a better production BUT, we do not want the water to boil because water in steam form will escape the cell and corrupt the HHO test production. The efficiency of a cell is measured in MMW. Too much energy in the cell will transform it in a water boiler. Hoppe this helps!?

[flipster12000]

You will need 4 (2.3 volts per gap)or 5 (2.8 volts per gap) neutral plates at 13.8 volts. If you run 1.5 volts per gap,your production will be very low because stainless steel has a fairly high resistance to voltage.

[flipster12000]

If you don't have the proper voltage drop across the cell, You will get a thermal runaway condition where as the water heats up, it wants to draw more current which will create more heat which will create more amp draw and so on until the cell eventually melts down and explodes.

[davidrrrd]

that is parelel,

searies would have neg to pos conections linking them.

any power used passes threw them all.

would help reduce posability of a runnaway prosses.

but a pwm is still a good Idea.

[cassoftware1]

If your having problem with heat in your Vid. Why not put the cells in series. dividing the volts across the cells. Think you maybe should and I could be wrong. Go to 6 cells this should from what I have seen eliminate heat in the cells.

[lutherp40]

As drawn in the video, this a parallel circuit.