My 1999 WJ Limited 4.0 w/ Flowmaster cat-back

[gbattilanaf]

The tapping is because of hidraulic valve lifter failure...typical on any 4.0L jeep engine. Try using the "restore" additive....it has worked for me in all 4.0L jeeps I've owned.

[rub16831]

how much was it for the new pipe?

[xStraightEdgexH20]

they really dont sound loud on the v6's

how loud are they in person?

[WoWKazo]

Well it wouldn't be as loud if I kept the stock piping on there... since this video the jeep's had a few thousand miles put on it, and it's really been broken in.. Put it this way, I pulled up next to a modded out mustang the other week, and my truck drowned it out.. haha, you couldn't even hear the mustang after I hit the gas.

[dawgsfan51193]

I'm gunna sugest a black westin brush gaurd for your jeep. It looks sick on mine and would look nice on yours too. Also gotta get a system inside man.

[rctruckdriver3]

is that a v8 or v6

[WoWKazo]

4.0L Inline 6.

[seniorbuddie]

@WoWKazo ok so its not my jeep. but i have an 01 limited. arent all the limited all 4.7? in the 99-06?

[bestskaterer]

not bad. check out my super 44 on my jeep wj and tell me what you think

[Ajaces]

That tapping you first get at startup, I've got that too. I haven't been able to figure out what it is.

[WoWKazo]

The tapping noise went away.. I've since done ALOT more work to the jeep, including: Intake, Plugs, T.B spacer, Synthetic oil, and soon to have a hypertech programmer.. Not too sure what It was, might have just been wear on the internals.. since I changed over to synthetic, the truck runs like it's brand new

[bosephjarrows]

why is that muffler silver? did you paint it? becuase super 44 is black.

[WoWKazo]

The whole setup is painted with a silver rust resistant paint, it's definatley a super 44 though.

[shitbag139]

where's the new video?? I didnt see it on your page?? I was all bummed out

[mmovrich22]

is that just exhaust or did you put anything else in the engine to make it sound better

[WoWKazo]

That's all exhaust.

[shitbag139]

nice, your buddy that didi the bends, I'm in mass so, where's he at?? and does he do real mandrels?? proably not,the machine to do that is like 40 thousand bucks for piping under 3 inches

[WoWKazo]

He's in Whitinsville, MA

Shop is called Menard's

It's literally right next to where they keep the F.T.I. Tour busses at.

[343FirNaTine]

if it's a shop they have them. and $40,000 is nothing when it comes to shop equipment. at my friend's shop, his boss buys new cnc-machines that cost around $200,000 every so often.

[OIIIIIIIO10]

Bangin jeep my man!

[KingOfTheClutch]

I miss that Mass accent, I lived in Haverhill for YEARS.

Still have my jeep from there.

Your Truck sounds GREAT!!!!

[WoWKazo]

Hahaha, thanks bro. Yeah my accent is a bit boston-ish. The truck sounds even better now, the exhaust is starting to get broken in.. I'll have more vids up soon.

[KingOfTheClutch]

lol, i hear ya, mine kicks in here and there, I used to drive prople nuts with the way the accent kinda silents out the "R"s