when i start the car up there no beeping noise it shakes badly, ders no acceleration an then after i turn the key a few times it kicks in, it only happens in the morning and then its ok for the day...the beepin noise comes on after a few miles?
Hola compi, yo lo he probado pero no va, utilice un cable del numero 7 al numero 19 y le di al contacto sin arrancar...., pero paso ma d eun minuto y nada de nada, tambien puente el numero 7 a masa u yampoco, me puedes detallar si utilizastes alguna bombilla o diodo?, espero tu respuesta, gracias
U put power on pin 7 and 19, google the pin map. the pins can be found as a round connection in the engine compartment, if u dont have the bmw reset tool this is the easiest way.
1. Locate the 20-PIN DLC Connector. It is located under the hood, on the firewall next to the fuse box.
2. Connect/Short pin 7 and pin 19 with wire/pliers/paper clip. MAKE SURE YOU CONNECT ONLY THESE TWO TOGETHER! (They are labeled with small numbers next to each pin)
3. Turn ignition to position 2 (ON)
4. Remove connection/short after no more than 5 seconds for OIL CHANGE. 10 seconds for INSPECTION.
@kadett1989 I did the same like hampnich said, on my bmw e30, and it's work perfect. Try again and make sure you follow all the steps. Keep the key turned on until the oil lights dissapear (it took a little longer than 5 sec. after my counting, like 6-7 sec. but I'm not a machine so correctly will be around 5 sec. after a counter/watch)
Its a simple diy: just ground the pin nr 7 in the round diagnostic plug under the hood. then go into your car and put hte ignition on level 2 (not start the engine!). then just wait for about 3 to 10 secound untill the green lights turns on ;)
when i start the car up there no beeping noise it shakes badly, ders no acceleration an then after i turn the key a few times it kicks in, it only happens in the morning and then its ok for the day...the beepin noise comes on after a few miles?
suejohnjo 1 week ago
great video...what the fuck did u do
prepaidbrian 1 month ago 3
Hola compi, yo lo he probado pero no va, utilice un cable del numero 7 al numero 19 y le di al contacto sin arrancar...., pero paso ma d eun minuto y nada de nada, tambien puente el numero 7 a masa u yampoco, me puedes detallar si utilizastes alguna bombilla o diodo?, espero tu respuesta, gracias
elchicobatera 2 months ago
he is saying what to do in the description...
U put power on pin 7 and 19, google the pin map. the pins can be found as a round connection in the engine compartment, if u dont have the bmw reset tool this is the easiest way.
bloodhawk91or 4 months ago 2
fool
slugster1370 6 months ago
the likes/dislikes bar looks like a light saber that's about to slice this video's uploader's cock off
omfgwtfbbq90 6 months ago
wow, now how the fuck did you do that retard? what a waste of a video
bennyvega100 7 months ago
whahahaha
senekal2 9 months ago
man the shows how to do it thanks for putting a worthless video on here
quijasfrank 9 months ago 2
Solo hacer un puente entre el pin 7 y 19 y dar contacto.---- read the info dumbfucks !
Muslim2888 9 months ago
wtf.... the only thing I saw was, ignition on and it blinks grenn and ignition off,
thepricylon 10 months ago
lol wot a cock
cwtrehill 10 months ago
wanker
78SHAFER 11 months ago
thanks it helped a lot
echrizen 1 year ago
what is that ?????
7809778984 1 year ago
THAT WAS THE FUCKIN STUPIDEST VIDEO IVE EVER SEEN WTH...
truhercules 1 year ago 4
WOW, that is all i have to do....turn the key on and back off!! Holy sheep shit batman i am an auto repair GOD!!! what a fucktard!!
tandlak 1 year ago
now i know what to do...... oh wait no i don't :S you FOOL!!!
seanjames101 1 year ago
you french douchebag who posted this crap,you should shove the key up your ass
NICKNAC2110 1 year ago 3
???
maxehv 1 year ago
1. Locate the 20-PIN DLC Connector. It is located under the hood, on the firewall next to the fuse box.
2. Connect/Short pin 7 and pin 19 with wire/pliers/paper clip. MAKE SURE YOU CONNECT ONLY THESE TWO TOGETHER! (They are labeled with small numbers next to each pin)
3. Turn ignition to position 2 (ON)
4. Remove connection/short after no more than 5 seconds for OIL CHANGE. 10 seconds for INSPECTION.
hampnich 1 year ago 3
@hampnich
I`ve tried that on my E39 and didn`t make success. Nothing was happened. What do you think i`ve done badly?
kadett1989 1 year ago
@kadett1989 I did the same like hampnich said, on my bmw e30, and it's work perfect. Try again and make sure you follow all the steps. Keep the key turned on until the oil lights dissapear (it took a little longer than 5 sec. after my counting, like 6-7 sec. but I'm not a machine so correctly will be around 5 sec. after a counter/watch)
crime1bucharest 1 year ago
@hampnich followed your instructions, and it worked a treat. Thank you very much for saving me pots of money.
emmasean19711982 1 year ago
Its a simple diy: just ground the pin nr 7 in the round diagnostic plug under the hood. then go into your car and put hte ignition on level 2 (not start the engine!). then just wait for about 3 to 10 secound untill the green lights turns on ;)
oea69 2 years ago
what a complete idiot!!
trevgk 2 years ago 36
well that showed us alot!
colannelson 2 years ago 43
can u please tell us what u did in english also? please please.......i tried it and mine did not work...thank you
kingsemelo 2 years ago
tell us pls how u do this.thank's
pirelli309 2 years ago
otro no dices ni donde se deve de puentear explicale a la gente bien no nada mas engañes
bmwroberto 2 years ago
no vi nada
portugalmen 3 years ago
so what did he do to reset?
netsailor2007 3 years ago
motor m20 si
lacasitoazul 3 years ago
en un e30 sera = ????
rodrigop1984 4 years ago