Timm your a retard, it's a metal roll pan. Also, its spelled bumPer, not bumber. And yes the engine bolted straight up. The only thing needed is a lock up kit to have 4th gear work, they run about 70 dollars. And like was said below, it was completely carbureted. I took everything computer controlled off of it.
@SunShine0147 take out all the unnecessary wiring, the only wire i needed going to the engine was a positive 12 volt to the electronic choke on the carb, well that and a ground on the block. but its pretty straight forward, you just need the money and time.
its not a throttle body motor he says pre 86 so its a carburated motor. If it was a original throttle body moter all you would have to do is swap the intake manifold and slap a carb on it, 92 still has a 700r4 so not need for a computer.
@billybadazz11 if you could find a driveshaft with the same yoke and length it would work, but i dont think any trucks came with aluminum driveshafts, pretty sure its only aftermarket
Nice truck, only question is what is up with the stock air intake system? Its fine if you flip the lid on top of the filter upside down. If you do that it's like haveing a good intake that doesent restrict airflow, but for free. I did that on my 93' c1500 and it gave me an extra 25HP, you should give that a try.
specs on the cam?
rockinbass01 2 months ago
Timm your a retard, it's a metal roll pan. Also, its spelled bumPer, not bumber. And yes the engine bolted straight up. The only thing needed is a lock up kit to have 4th gear work, they run about 70 dollars. And like was said below, it was completely carbureted. I took everything computer controlled off of it.
thenickbutler1 9 months ago
did the older engine bolt right up to the stock tranny?
xxBM85xx 9 months ago
that truck is a piece of shit.. you dont even have a rear bumper on it. you just have a plastic straight edge bolted on where the bumber should be
Timmycky16 10 months ago
take that stupid fuck air cleaner dish off and by a k&n with a new dish
ride6your6bmx6 1 year ago
how did ya convert a throttle body injected engine to a carborated?
SunShine0147 1 year ago
@SunShine0147 take out all the unnecessary wiring, the only wire i needed going to the engine was a positive 12 volt to the electronic choke on the carb, well that and a ground on the block. but its pretty straight forward, you just need the money and time.
thenickbutler1 1 year ago
@thenickbutler1 plus, it was an entirely new engine lol. the old one was junk
thenickbutler1 1 year ago
its not a throttle body motor he says pre 86 so its a carburated motor. If it was a original throttle body moter all you would have to do is swap the intake manifold and slap a carb on it, 92 still has a 700r4 so not need for a computer.
revn57chevy 1 year ago
make a start up video
masonransom 2 years ago
@masonransom look at my other videos
thenickbutler1 1 year ago
where did you buy your wheels... i dont want to pay a lot ... only seem to see em listed for 900 bucks
weewoodeal 2 years ago
where did u get the aluminum driveshaft?
billybadazz11 2 years ago
From ur moms ass
billythefat 1 year ago
fuck u mean
billybadazz11 1 year ago
@billybadazz11 haha unfortunately i didnt get it from his moms ass, theres a performance shop near my house that i had make one for it.
thenickbutler1 1 year ago
@thenickbutler1 is there any nexer truck u could pull 1 out of that would fit? im really wantin 1
billybadazz11 1 year ago
@billybadazz11 if you could find a driveshaft with the same yoke and length it would work, but i dont think any trucks came with aluminum driveshafts, pretty sure its only aftermarket
thenickbutler1 1 year ago
@thenickbutler1 yea the 99 and up chevys did have em stock but im jus wonderin if it wud fit i might try and find 1 and see if it will
billybadazz11 1 year ago
@billybadazz11 what years your truck? and is it regular extended or crew cab
thenickbutler1 1 year ago
@thenickbutler1 its a 1990 reg cab stepside i got sum vids of iit on here
billybadazz11 1 year ago
This has been flagged as spam show
looks good man check out mine and tell me what u think
blackchevy0250 2 years ago
Nice truck, only question is what is up with the stock air intake system? Its fine if you flip the lid on top of the filter upside down. If you do that it's like haveing a good intake that doesent restrict airflow, but for free. I did that on my 93' c1500 and it gave me an extra 25HP, you should give that a try.
zlink8 2 years ago
never really thought of doing it, might give it a try. thanks man
thenickbutler1 2 years ago
No prob, best thing is it's free !!
zlink8 2 years ago
bull shit
NoSweatOffMySack 2 years ago
Nope, it was tested in autoshop class. The gain was at the flywheel, but it was a 25hp gain.
zlink8 2 years ago