Axial SCX10 winch, Ezrun 32T Rock Crawler Brushless motor program card, esc, lights operation

[Sn1P3r47KiLLeR]

what servo u using is it metal or plastic and hm u pay

[Ash7164]

@Sn1P3r47KiLLeR It’s the Tower Pro Digital Metal Gear Servo 48g MG995 Discontinued

Superseded by TowerPro MG996R Metal Geared Servo: Speed: 0.17sec/60deg(4.8V), 0.14sec/60deg (6.0V)

* Stall Torque: 9.4kg/cm (4.8V), 11kg/cm (6.0V) Cost £10 /$15 I use these in all type of cars, even 1/5th scale (not in planes or hellis though)

[dougnumber88]

how fast does it go with the lipo? and what's the mah of the battery?

[Ash7164]

@dougnumber88 Speed depends on gearing, stock gearing with the 7.4v 5000mAh lipo, 6-8mph. 45 - hr use on 1 charge : It's a crawler/trail rider so not built for speed ( i have a traxxas slash for that :)

[TactialMonkey]

make a vid of winch mounting im so confused help me please yours looks done right mine will look like ass help me and how the hell did you wire it

[Ash7164]

yes, enough power on 7.4v lipo battery

[KILLER1341999]

has this truck have enough power

[pmm4177]

Is that the Axial night vision light system? I have one but the wires aren't long enough and mine is mounted in a similar location, Did you lenthen the wires?? thanks

[Ash7164]

@pmm4177 No m8, it's not the Axial night vision light system.

It's the Tamiya LED Light Unit (TLU-01) item no 53909

comes with 2 white and 2 red, then just bought Item No 54008 Tamiya LED Light (3mm White) for the light pods

Tamiya LED Light Control Unit (TLU-02) Item No：53937 comes with brake lights also :)

Hope that helps, cheers Ash.

[butha72]

@pmm4177 There IS one. $70 search E-Bay for Axial AX24251 Night Visions System, it even makes the signal lights work when you turn. Comes with two rear light, 2 front lights, and 2 signal lights plus the control box.

[gudrn]

very nice car and great vid. i'm thinking about getting one 32T motor, but i've already own a 60A Ezrun ESC. do you think my ESC will provide a hard drag brake with that motor or i'll need a specific ESC to do that? tks my friend

[Ash7164]

@gudrn You should have no problem with 60A hobbywing esc, just set the drag brake to with a program card or with the beep method

5.Maximum BrakeForce 25% 50% 75% 100%

6.MaximumReverse Force 25% 50% 75% 100%

7.Initial BrakeForce= Drag BrakeForce0% 20% 40%

[gudrn]

@Ash7164 awsome, bro. thanks... today i've just got a SideWinder SCT and installed on my Pajero CC-01 with a 85T motor... it breaks great.

[TheCrackHeads11]

nice



[Ash7164]

@gotfatbob09 It's a Hobby Wing Ezrun 32T Rock Crawler Brushless motor + 35A V2 ESC

about £50 UK From EBay. You need a program card to make setup a lot easier.

[obla95]

what shocks are those ?

[Ash7164]

@obla95 RC4WD DOT COM 88mm ones or JUNFAC DOT COM do some lovely shocks

[obla95]

@Ash7164

do you mean the 80mm ones?



[Ash7164]

@obla95 when i bought them they were 88mm, just measure up the old shocks and see what size suits you best.

[idoeverything733]

@Ash7164 this is huge to me so please respond ive been looking for those shocks where can i get them?

[Ash7164]

@idoeverything733 The shocks come from RC4WD DOT COM in the usa or JUNFAC DOT COM do some lovely shocks for a SCX Just bought a set of zero shocks from junfac on feebay for converting my cr01 back to conventional suspension, look very nice quality :)

[KWAKNZ]

Thank you for the reply, is it the universal snorkel? store.rc4wd.com/Factory-Univer­sal-Scale-Snorkel_p_311.html

[Ash7164]

@KWAKNZ yes m8 that's the 1, watch out if you buy from the usa and you live in uk, I always ask if they can de-value

goods or ask to mark as gift on the customs declaration as customs and the post office sting you sometimes double the value of the goods.

[KWAKNZ]

@Ash7164 Nah all good, have bought stuff from them. and I live in New Zealand so no issues in the past from importing. Have ordered it so just awaiting. Thank you!

[zmattos00]

what shocks r u using and where did u get them?

[Ash7164]

@zmattos00 go to the rc4wd web site you will see the 88mm shocks there

[alextronique]

How is the 32T motor? Coogging? low low speed? any low speed runing video please?

[Ash7164]

@alextronique not sure i have hurd the word coogging before! the night time part of the video is low speed, the other video hill climbing is just about at max speed. The brushless motors last well as long as you keep them dry.

[SuperCrazydude1234]

can u post a vid on how to set up a winch from the start

[Ash7164]

@SuperCrazydude1234 sorry m8 can't do as I sold the Tx sometime ago. Better off getting a tx with a 3 way aux 3rd channel switch like the DX3-E as you have to adjust the end point travel up to say + 20 and more to make the winch move out then back to 0 to stop winch the - 20 and more to make the winch retract on the DX3, get it wrong and you will tangle the wire round the drum or snap the winch wire.

[KWAKNZ]

Hi, what snorkel is that? and where did you get it from? cheers, nice truck!

[Ash7164]

@KWAKNZ the snorkel is from the USA. The company is RC4WD

[rcBitz]

@Ash7164 Which truck was is listed to fit? thanks fo your help. Great looking truck

[Ash7164]

I make 1 little cardboard template of the winch base with the holes punched through for the mounting screws and 1 template for the cut out on the skid plate. Trial fit the winch so it looks centered, draw round the winch then tape the cardboard template where you marked the winch and drill the mounting holes. Then place the skid plate template on the skid plate centered and draw round it before cutting the skid plate. Its best done with a hobby drill kit, from DIY store £15, Dremel is £35-£80

[CrazySilentAssain]

@Ash7164. what motor are you using and speed controller

[Ash7164]

@CrazySilentAssain, Hobbywing Ezrun 3in1 Motor Combo (ROCK CRAWLER)

32T Brushless Motor (1200kv) + 35A SL v2 ESC

Look on EBay around £50 UK pounds shipped from Hong Kong

Works well but does need setting up with the program card for better drag brake.

[Ash7164]

@CrazySilentAssain, Hobbywing Ezrun 3in1 Motor Combo (ROCK CRAWLER)

32T Brushless Motor (1200kv) + 35A SL v2 ESC

Look on EBay around £50 UK pounds shipped from Hong Kong

Works well but does need setting up with the program card for better drag brake.

[Ash7164]

DC the bumper is standard, winch is mounted on the cross brace. Just cut out a rectangular hole from the top of the alloy bash plate a little wider than the winch drum so the wire reels out and in without snagging the bash plate. If you taper the cut both sides so the cutout is slightly narrower at the bottom it looks nicer.

[DCMotorSport91]

@Ash7164 ok, how hard is it to mount the winch, im picking up my new scx10 this weekend and a winch is the first to go on it.

[DCMotorSport91]

where did you get that bumper with the winch opening under the lights? or can you make it?

[Harvz78]

What is the length of that shock and where did you bougth it?

[Ash7164]

.@Harvz78 88mm shocks fitted, from RC4WD in the USA. If you want more crawling ability, higher ground clearance use 100mm shocks and put 2.2" wheels on. If you from the UK and buy from the USA ask if they can make out customs declaration as GIFT or you will be charged import duty and post office handling fee If they will not do this try shopping around. I find most sellers are very helpful except team gonads

[atltybo]

Nice rig bro.

[Ash7164]

@atltybo cheers m8

[forresto69]

is there any way you can rive me a list of all your mods iv got the scx10 tr the one with the dingo body

[Ash7164]

@forresto69 RC4WD shock absorbers with internal springs,3RACING auto winch steel winch rope,spotlights.The rope on front bumper and all straps gas bottles ground anchor tool box large jerry can are from Don_jarr (type "crawler" in EBay uk search then click radio control tab on left hand side menu you can find accessories from there.

PROLINE roof rack,accessory pack #1 with coolbox,jerry can,winch,strap box.

Accessory pack #2 with spade high lift jack,etc. Tamiya TLU-01 Light Unit

[law51]

wat snorkel did you use

[Ash7164]

@law51 the snorkel is from the rc4wd.com web site. If you buy from any USA always ask them to mark customs declaration as gift or uk customs and the post office will charge you.

[Ash7164]

.dremel type multi tool and wear goggles or mark out the shape and drill a hole into each corner just big enough for a junior hacksaw blade to pass through cut out the shape then file the rounded corners with a small flat file

[krez76]

Hey how did you create the rectangle hole in the metal plate for the winch to go through?