1. Do NOT wash the filter from the outside in. Always wash clean to dirty side.
2. Do NOT put so much oil on the filter. It only needs a light but complete oiling. The filter shown should only use about 10-12 ml of oil. Looks more like 20+ml was used in the video. This WILL get on your MAF sensor and you will be replacing it ASAP.
For future reference, if your going to show a "HOW TO" please know how to do it correctly.
Oh dear. You are supposed to run the water from the inside of the filter to the outside. All you have done is push the dirt deeper in to the filter. Filter still looked damp when you applied the oil (which you also used far too much of). This is how to RUIN a K&N air filter.
When you rinse the filter make sure the water is directed from the clean side ( inside the cone in this case) to the dirty side. Otherwise you force the dirt deeper into the filter. Air dry the filter until it is completely dry. This will take a good part of ta day. Do not use a dryer or leave in the hot sun. This guy's procedure is a sure fire way to ruin your filter and get dirt into your engine.
I can't believe that with all the negative comments about the obvious mistakes in this procedure that ZERO hasn't removed this video. He needs to read the directions that came with his K & N cleaning kit, and then clean his filter out in the garage instead flushing solvents down the drain.
wow, when I did mine, I applied cleaner 3 times, made the filter nearly white. and waited a full day before I applied the oil.... and applied a WHOLE lot more oil... it's still dripping oil and haven't installed it yet.
Where's the missing part of the video where his Mama flips the fuck out and kicks his ass for using the bathroom sink? Son R U Retarded? BEEM, BOOM, BAAM ...!!!!
First off he cleans the filter from the outside in, should be from the INSIDE out.......then it takes LONGER than 15 minutes for them to dry....mine took an hour in the HOT 90 degree sun.
THEn he puts WAAAAAY too much OIL on the filter.....on a car with a map sensor the sensor would fail.,
@455Transam Your stupid, putting too much oil is better than putting not enough oil. It's better and doesn't have an effect except it might affect the next time he has to change his air filter but better then the bike engine breaking.
I'm pretty sure on the instructions it says depending on how dirty it is you should repeat steps 1 and 2..... You probably should have done that sir. lol
Why do you have to let the filter sit and dry...why cant you blow dry it? Hmmm? I always just buy a new filter have the technician change it and then Im off...but gas prices are HIGH so now Im thinking of just washing to SAVE $...
A major mistake in this video is in the rinsing. You should always at least start the rinsing from the inside out. It's much more efficient to rinse the particles out the same way they came in. If you want to rinse the outside, at least do it after you've rinsed most of most of the dirt from the inside out. I always start spraying the cleaner from the inside out also. This helps remove and push the particles in the direction you want them to go. All this is in the instructions in the kit.
@salttram1 Yup, now he moved all his dirt to the inside. Also, if you dont let it dry ALL THE WAY, it will damage you MAF sensor. Too much oil will also damage trhe MAF sensor. So, from inside out! Let it dry! light oil.
Ok vid, well not really because you are actually supposed to rinse the filter from the inside out NOT from the outside in. If you rinse from the outside in, you are pushing dirt deeper into your filter. If you rinse from the inside out, you are rinsing the dirt out of your filter instead of pushing dirt back into you filter. Also, It takes a couple of hours for the filter to dry, NOT 15 mins. And lastly, the guy in this vid put way too much oil on the filter, you only need a light coating
Instantly knew it was tetris (nes version) other than that... Dude ... your suposed to wear rubber gloves when you use degreasers.
that shit can remove fat from your skin and leave your fingers all crusty... I know because it happened to me like 13years ago, took a year for my hands to heal.
This is all wrong, never rinse the outside first. Rinse from the inside as the dirt will be stuck on the outside. Rinsing the outside pushes grime into the inside of the filter and then fills the inside of the cone with dirt. no need to spray the inside, the cleaner will soak into the cloth. Also i use this kit on my Injen intake and it works just fine!
I have had mine on my Silverado for Three years. I suppose it's time to clean it!... I bought the cleaner when I bought the K&N. I have a mission to compete now!
I have had mine on my Silverado for Three years. I suppose it's time to clean it... I bought the cleaner when I bought the K&N. I have a mission to compete now!
@vda1288 Im pretty sure you can, I actually have a K & N filter on my injen intake (bought car used, so I didnt mix and match myself) so I'm pretty sure the filters are basically the same, then again I could be completely wrong
Should have rinsed from the inner side, not the outside like was done in this video. By washing the outer portion dirt was just pushed into the inner portion of the filter.
Thank you, I didn't have a clue where to start. I've never owned a filter like this and I was not sure what how to go about doing it, after asking a dozen auto places if they would clean it and hearing NO, I figured youtube would have my answer. Thanks
@urbex2007 Did you just try to tell me that the INTAKE passes air BOTH ways? So you're telling me that it serves as an intake and an exhaust? For the love of god tell me that's not what you're on about. You rinse inside out so that you're not effectively pressing dirt into the intake using water pressure.
Also, yes, the oil stays wet, it's oil of course it does. It stays wet to help dirt stick to it and aid filtration. It will only f with your MAF sensor if YOU USED WAY TOO MUCH OIL.
Not recommended for any turbo carged car due to the much higher airflow, it can't cope and the oil which never dries gets sucked in to the MAF sensor. Mine was £200 to repair. K&N also don't publish or give any figures on what they claim the filtration rate is in microns. I do not want my engine shotblasted as it allows dirt through. Small surface=bigger holes. K&N does NOT filter and they don't claim it does. A paper filter is 10times the surface area and doesn't restrict flow in any way.
@urbex2007 Also, you are the only person not recommending it for a turbo charged engine. Not a reliable source. I know plenty of turbo cars running the filter properly with out using too much oil for hundreds of thousands of miles. I am one of them (twin turbo v6). Have you done any testing to confirm that it allows dirt through? And how much? Obviously it will, and K&N post results of something like 96-99% filtering efficiency. NOTHING will block ALL of the particles. They do call them filters.
and dont tell your mom you used her good sink to clean your air filter.
lol. Ill be off to find a better video. Never having dont this before (new car) I new better than what you were doing. Atleast I learned the names of the products I need to go and get. fuck...
@greatdane50 It doesn't actually dry. It stays damp with oil, that's why it flies off and damages MAF sensors like it did with mine. Put a K&N in contact with a piece of cardboard and leave it for a few days, it will be saturated in the oil. I don't use them now as they do NOT filter to the standard of a paper element, so don't want to sandblast my engine with dirt the K&N allows through. K&N used clever marketing tricks and advertising, they still can't say how many microns they filter to!!!
@BMWLDRider You seem to have contradicted what K&N claim about surface loading then, especially about the operation of what they don't say is a filter. People call them a filter so K&N go along with it, but don't say anywhere it filters - because it doesn't really. The K&N has a small surface area so wil block faster than a paper element with a 13ft surface area, K&N is 2ft max. So the holes in a K&N need to be 10 times bigger, allowing 10 times more dirt through than a paper filter. Bin it.
@urbex2007 Also. I would love for you to link me to somewhere that proves a K&N air filter functions worse than a stock air filter. The numbers you posted @BMWLDRider are confusing and don't make sense. Perhaps it was just your sentence structure. I personally know of a ~1000hp turbo car running a K&N filter with no ill effects. An open filter like this will not work for every car without proper tuning (Subaru STI for ex.) Do your homework and read directions before use.
After how many miles should I clean mine? And I have the filter thats exactly like the OEM filter but with the K&N fibers so is the process any different?
@desimunda116 Well, i clean mine every 10,000 miles. and i never tried to clean another washable filter with the K&N kit, but i would image it would work and it should be done the same exact way as in the video
@desimunda116 They say to at least check it every 30k miles, but it all depends on your driving conditions. I also have the drop-in replacement filter, and mine lasted about 25k-30k miles before it needed to be washed.
@nieldcaj Doesn't matter which way you clean it, is passes air both ways, the cotton isn't a one way system. This just shows the general lack of knowledge from people buying these devices. Learn about filtration, gasflow and save your money. If K&N filtered to anywhere near the standards of a paper element (which doesn't restrict flow) car manufacturers would use them, so would air conditioning companies. K&N have only scammed the boy racer market, the rest have common sense. K&N=no filtering
Switching FINGERS!! Apparently this is a tiring procedure.. hah
CENTAUR559 14 hours ago
This is NOT a good way to do this.
1. Do NOT wash the filter from the outside in. Always wash clean to dirty side.
2. Do NOT put so much oil on the filter. It only needs a light but complete oiling. The filter shown should only use about 10-12 ml of oil. Looks more like 20+ml was used in the video. This WILL get on your MAF sensor and you will be replacing it ASAP.
For future reference, if your going to show a "HOW TO" please know how to do it correctly.
dsmithwc04 1 day ago
Aren't you supposed to run the water from the inside (clean side) out???
cumminscrazy30 3 days ago
@cumminscrazy30 Yes you are
nascarbuckeye 3 days ago
no way that would dry in 15 mins, my one took hours in the hot sun
Gonzarelli 1 week ago
or just buy a new factory filter
DJzSith 1 week ago
may be a dumb question but if u dont have those sprays can you just clean it with water?
anthonee03 1 week ago
@anthonee03 You'd want to re-oil it for sure. Just stop being cheap and buy the sprays!
BattyBitz 1 week ago
carb cleaner dose the same job
PJTrucker 2 weeks ago
Under normal conditions, How often should you clean and re-oil a K&N air filter?
TheOne42 2 weeks ago
Last step: Get your ass kicked for doing this in your bathroom sink.
gatoflacoroad 2 weeks ago
Oh shit that filter was filthy!
pickmelter38 1 month ago
@pickmelter38 lol
mrbigtian 1 month ago
Takımı 65TL, bir temizlemeye 1 kutuyu bitirdin be abicim...
aydemirburak 1 month ago
thats kind of a small filter. what kind of car do you have it on?
Pitchblac7 1 month ago
that index finger is a warrior,so is that thumb
JThought320 1 month ago 2
Damn your the spray king kns filters !!!
79rudeboi 2 months ago
It looked like disease in your sink when you first rinsed it.
fifthsannin 2 months ago
Oh dear. You are supposed to run the water from the inside of the filter to the outside. All you have done is push the dirt deeper in to the filter. Filter still looked damp when you applied the oil (which you also used far too much of). This is how to RUIN a K&N air filter.
sgc1v07 2 months ago 2
101 thousand views because of the Tetris soundtrack. EXCELLENT choice! :)
SuperTanuki64 3 months ago
When you rinse the filter make sure the water is directed from the clean side ( inside the cone in this case) to the dirty side. Otherwise you force the dirt deeper into the filter. Air dry the filter until it is completely dry. This will take a good part of ta day. Do not use a dryer or leave in the hot sun. This guy's procedure is a sure fire way to ruin your filter and get dirt into your engine.
CBR11X 3 months ago
Damn!!
kestkr 3 months ago
you don't need to use that much cleaner bro lol
askloglog 3 months ago 3
Your mom use it to strain coffee or something??
Garabato609 4 months ago
your sink sucks ass
vex123 4 months ago 8
BP would be proud of you cause all that sht is going to the ocean
trulymeparker 4 months ago 3
You didn't do one thing right when cleaning your filter.
mekalis69 4 months ago
@mekalis69 I'd be glad if you would show us how to do it properly, mister tiger woods jr.
KillaPillaP 4 months ago
you wife is gonna kill you when she see wut you haave done in her sink
123ryancarter 4 months ago
wash your hands bro.
GOTHMDOC1 5 months ago
You are supposed to rinse the filter from the inside out (Clean to Dirty side)
GOTHMDOC1 5 months ago 3
If you drop your tooth bursh in there....leave it in there. :s
doctoroctagonaBLARGH 5 months ago 2
next video "HOW TO UN CLOG YOUR DRAIN" lol
rudybo0oty 5 months ago 57
@rudybo0oty this take for ever i would just go by a new filter simple
ERIC933G 1 month ago
THANK YOU!! Now I know how to clean my air filter! Why can't all the how to videos on youtube be as good and simple as this??
crapamole 6 months ago
All that oil filter spray is really going to clog up your MAF quick.
drdouche1 6 months ago
You don't need to use that much cleaner!
bobo1623 6 months ago
My wife would kill me if I tried this in our bathroom.
DownzyTheBear 6 months ago 5
Tetris music can make anything sound fun...
"Hey want to go change the oil?"
"nahhh."
Dum dada dum dada dum...."
"On second thought......."
Callabretto 6 months ago 49
@Callabretto That really made me laugh... Thanks!
phantompanic 5 months ago
Hey your suppose to rinse water from the inside out... just sayin!
TheLuckeydc7 6 months ago 4
You definitely need to clean that wayyyyy more often
crawfordguard 6 months ago
(Squirt squirt squirt squirt squirt squirt) *grunt* "Getting...tired" *switch to thumb* (Squirt squirt squirt squirt squirt squirt) "...tired again" *switch to index* (Squirt squirt squirt squirt squirt squirt)
soulsick410 6 months ago 3
wife walks in and says what the fuck are you doing? this is where we brush our teeth!!!
felipemercado87 6 months ago
I can't believe that with all the negative comments about the obvious mistakes in this procedure that ZERO hasn't removed this video. He needs to read the directions that came with his K & N cleaning kit, and then clean his filter out in the garage instead flushing solvents down the drain.
75t150 7 months ago
@75t150 Less QQ, more pew pew
darkchu 7 months ago
sexy air filter cleaner!
HamadHHAG 7 months ago
The music is Russian & the 1st tune is "Karobushka."
I'm a musician & own a K&N AIR FILTER.
DERBYCLOWN 7 months ago
You run the water from the inside/clean side.
thechaser1985 7 months ago
Sexy hand veins
XxLongjohnzXx 7 months ago
and kids? dont do this in your mums fucking sink or you will be owned!
se7en1976 7 months ago
too much filter oil is a known cause of the MAF sensor wires fouling up
holdenisthebrad 7 months ago
wow, when I did mine, I applied cleaner 3 times, made the filter nearly white. and waited a full day before I applied the oil.... and applied a WHOLE lot more oil... it's still dripping oil and haven't installed it yet.
Riggro 7 months ago
way to much oil, and you should wait longer than 15 mins after you wash
but nice music
bottle2lip 8 months ago
damn't the cleaner smells like fish!
fofomaan 8 months ago
damn't the cleaner smiles like fish!
fofomaan 8 months ago
lol can i just throw it in the dishwasher?
killerkrab42 8 months ago
@killerkrab42 lol no
markssite 7 months ago
Helpful. Thanks
mikesdaddy1 8 months ago
awesome tunes
icychap 8 months ago
did you bake that filter or something?
JayDee973 8 months ago
Are you not supposed to wait until the filter is dry before applying the oil?
best333WillC 8 months ago
good thing your mom lets you use the sink !
& that mario music has to go dude !
bmw76308 8 months ago
Holy crap, you used SOOO much oil... I used maybe HALF of that and killed my MAF sensor the first time I cleaned mine :(
robisconfusedd 8 months ago
Dont let you mom or wife see ya clean the filter in the sink cuz they will blow their top!
lrg863 8 months ago
Where's the missing part of the video where his Mama flips the fuck out and kicks his ass for using the bathroom sink? Son R U Retarded? BEEM, BOOM, BAAM ...!!!!
damianfonseca 8 months ago
Comment removed
damianfonseca 8 months ago
Thx Zero this helped a lot
Terminater679 8 months ago
the music's made me feel so sleepy somehow...
Fubu 9 months ago
FAIL!!!!!!!!
bmclaren45 9 months ago
great fukin video
santibulous 9 months ago
that filter was dirty as shit!
mike3oo 9 months ago
I hope that filter already came brown or you could use a new one.
Finalize777 9 months ago
This video is ALL wrong!
First off he cleans the filter from the outside in, should be from the INSIDE out.......then it takes LONGER than 15 minutes for them to dry....mine took an hour in the HOT 90 degree sun.
THEn he puts WAAAAAY too much OIL on the filter.....on a car with a map sensor the sensor would fail.,
DO NOT CLEAN YOUR K&N's LIKE THIS!
455Transam 9 months ago 6
@455Transam Your stupid, putting too much oil is better than putting not enough oil. It's better and doesn't have an effect except it might affect the next time he has to change his air filter but better then the bike engine breaking.
rjc0l3 9 months ago
@rjc0l3 No you're an IDIOT....the bike engine won't "break" and too much oil is NOT "better"....ask K&N the manufacturer of the filter!
455Transam 9 months ago
@455Transam Your a retard, you are just retarded lol. Where does K&N's Manufacture say that? hmm? Where?
rjc0l3 9 months ago
@rjc0l3 Do some research Moron it's YOUR vehicle....follow his instructions if you want!!
455Transam 9 months ago
I'm pretty sure on the instructions it says depending on how dirty it is you should repeat steps 1 and 2..... You probably should have done that sir. lol
Drumsauce136 9 months ago
Thanks for the instruction, but I don't think it is very Eco friendly dumping the chemicals down the drain.
Rotuma01 9 months ago
2nd music is from lvl2 tetris...love it.
sphinxofthenewage 9 months ago
7 dislike don't know how to drive a car.
kcssweetboy 10 months ago
if your air filter looks like that after 10k you might want to shorten your interval
mitsufq360 10 months ago
tetris theme is my ringtone so i just was like wtf is going on
zoolander070 10 months ago
Why do you have to let the filter sit and dry...why cant you blow dry it? Hmmm? I always just buy a new filter have the technician change it and then Im off...but gas prices are HIGH so now Im thinking of just washing to SAVE $...
1999GAGTHO 11 months ago
thanx for the vid. I went out and did mine right after watching. lol
kpckutsum 11 months ago
GOOD Video
Beastie583 11 months ago
bad instructions
it should be hosed from in
ugly sink >lol
hussamor 11 months ago 2
should probably use gloves when u do that
mustaffa1611 11 months ago
Zero2242 and Importracer4life69 are talking about tetris music and playing tetris..NERD ALERT!! ...Someone need to "get some"..LOL.
GTnumber1 11 months ago
A major mistake in this video is in the rinsing. You should always at least start the rinsing from the inside out. It's much more efficient to rinse the particles out the same way they came in. If you want to rinse the outside, at least do it after you've rinsed most of most of the dirt from the inside out. I always start spraying the cleaner from the inside out also. This helps remove and push the particles in the direction you want them to go. All this is in the instructions in the kit.
salttram1 11 months ago 2
@salttram1 Yup, now he moved all his dirt to the inside. Also, if you dont let it dry ALL THE WAY, it will damage you MAF sensor. Too much oil will also damage trhe MAF sensor. So, from inside out! Let it dry! light oil.
heatherandpaul2 10 months ago
Thanks buddy. That was cool.
arizoboy 11 months ago
Since dirt goes from the outside in you should clean it from the inside out. Just a TIP to get it even cleaner next time!!
2LateIWon 1 year ago
your moms gonna be mad about all that dirt in her sink...
DSMstreetRunner 1 year ago 2
Um ya your supposed to rinse from the inside (clean side) out.....
bscrash22 1 year ago
can you do this with just soap and water? and what happens if i dont use the oil any alternatives?
brandonm1392 1 year ago
@brandonm1392 NO
belizetj 1 year ago
Ok vid, well not really because you are actually supposed to rinse the filter from the inside out NOT from the outside in. If you rinse from the outside in, you are pushing dirt deeper into your filter. If you rinse from the inside out, you are rinsing the dirt out of your filter instead of pushing dirt back into you filter. Also, It takes a couple of hours for the filter to dry, NOT 15 mins. And lastly, the guy in this vid put way too much oil on the filter, you only need a light coating
theREALnizzle 1 year ago 5
@theREALnizzle<----- You should make a video on how to do it properly. :/
irock63 11 months ago
comedown you amost lose some beef
HamadHHAG 1 year ago
and the wife/girlfriend ahs you sleeping on couch for a week afterward
stupidone1977 1 year ago
btw you should let the filter DRY ALL THE WAY before applying the oil... not in the sink
CEEPMDEE 1 year ago
Instantly knew it was tetris (nes version) other than that... Dude ... your suposed to wear rubber gloves when you use degreasers.
that shit can remove fat from your skin and leave your fingers all crusty... I know because it happened to me like 13years ago, took a year for my hands to heal.
CEEPMDEE 1 year ago
bet mom loves you very much!!!!
hjewell2 1 year ago
the background music makes me wants to play tetris :\
importracer4life69 1 year ago 60
@importracer4life69 wow ur the only one that figured out that the music is from tetris u get an A+
zero2242 1 year ago 28
@zero2242 ahaha thanks, very good video btw (:
importracer4life69 1 year ago
@zero2242 hell yah gameboy tetris is the shit
magnetik297 9 months ago
@zero2242 ... you can't be serious about no one relating this music to tetris...
ThatsTooSmall 9 months ago
@zero2242 why u hatin
samandllamas 6 months ago
@importracer4life69 makes me wanna play zelda kinda
MrCheez1 11 months ago
This is all wrong, never rinse the outside first. Rinse from the inside as the dirt will be stuck on the outside. Rinsing the outside pushes grime into the inside of the filter and then fills the inside of the cone with dirt. no need to spray the inside, the cleaner will soak into the cloth. Also i use this kit on my Injen intake and it works just fine!
Craiger29 1 year ago 2
kind of sick brushing your teeth in the same sink
joetierra1 1 year ago
@joetierra1
He doesn't lick the sink when he is done brushing does he?
ThirdgenTa 1 year ago
@joetierra1
He doesn't lick the sing when he is done brushing does he?
ThirdgenTa 1 year ago
@ThirdgenTa im just saying what if the toothbrush feel in the sink
joetierra1 1 year ago
@ThirdgenTa im just saying what if the toothbrush fell in the sink
joetierra1 1 year ago
This has been flagged as spam show
I have had mine on my Silverado for Three years. I suppose it's time to clean it!... I bought the cleaner when I bought the K&N. I have a mission to compete now!
clutchisgood 1 year ago
I have had mine on my Silverado for Three years. I suppose it's time to clean it... I bought the cleaner when I bought the K&N. I have a mission to compete now!
clutchisgood 1 year ago
jesus what were you filtering with that thing coffee?!?!
jimmy562 1 year ago 5
Good video, except rinse off air filter with cool low-pressure water from the clean side out in order to flush the dirt out of the filter.
JM1FC3311h0518346 1 year ago
this video is so helpful. Thankyou very much :)
HAYMRKELLOGSMAN 1 year ago
nice jew music
bismillahmashallah 1 year ago
helpful vid, thanks.
i would imagine i can use this kit for the cone filter on my injen CAI?
vda1288 1 year ago
@vda1288 Im pretty sure you can, I actually have a K & N filter on my injen intake (bought car used, so I didnt mix and match myself) so I'm pretty sure the filters are basically the same, then again I could be completely wrong
Dean5629 1 year ago
helpful vid, thanks.
i would imagine i can use this kit for the cone filter on my injen CAI?
vda1288 1 year ago
Straight and to the point! Great Video! going to try it out right now =)
djski121 1 year ago
Tetris!!! 98'
juve89 1 year ago
this music reminds me of the gameboy pokemon
Trigonster93 1 year ago 3
Should have rinsed from the inner side, not the outside like was done in this video. By washing the outer portion dirt was just pushed into the inner portion of the filter.
DizoAZ 1 year ago
wow this is really helpful. Thanks for posting it. I need to recharge my Blasters K&N filter and this helped
gottagofast12 1 year ago
Thank you, I didn't have a clue where to start. I've never owned a filter like this and I was not sure what how to go about doing it, after asking a dozen auto places if they would clean it and hearing NO, I figured youtube would have my answer. Thanks
ironlyon13 1 year ago
i throw mine in the washing machine downtown
erectionaffection 1 year ago
good job man
h64novic 1 year ago
This has been flagged as spam show
thumbs up for the music
ElDiabloDiarrhea 1 year ago
stupid music
Tutinet1 1 year ago
Urbex....I don't think you know of what you speak......
The first "Law of Holes" is when you're in one....stop digging!
You are making yourself look foolish.
Just sayin.
BMWLDRider 1 year ago
@urbex2007 Did you just try to tell me that the INTAKE passes air BOTH ways? So you're telling me that it serves as an intake and an exhaust? For the love of god tell me that's not what you're on about. You rinse inside out so that you're not effectively pressing dirt into the intake using water pressure.
Also, yes, the oil stays wet, it's oil of course it does. It stays wet to help dirt stick to it and aid filtration. It will only f with your MAF sensor if YOU USED WAY TOO MUCH OIL.
nieldcaj 1 year ago
Not recommended for any turbo carged car due to the much higher airflow, it can't cope and the oil which never dries gets sucked in to the MAF sensor. Mine was £200 to repair. K&N also don't publish or give any figures on what they claim the filtration rate is in microns. I do not want my engine shotblasted as it allows dirt through. Small surface=bigger holes. K&N does NOT filter and they don't claim it does. A paper filter is 10times the surface area and doesn't restrict flow in any way.
urbex2007 1 year ago
@urbex2007 Also, you are the only person not recommending it for a turbo charged engine. Not a reliable source. I know plenty of turbo cars running the filter properly with out using too much oil for hundreds of thousands of miles. I am one of them (twin turbo v6). Have you done any testing to confirm that it allows dirt through? And how much? Obviously it will, and K&N post results of something like 96-99% filtering efficiency. NOTHING will block ALL of the particles. They do call them filters.
nieldcaj 1 year ago
Rinse from inside out.
Let it dry overnight. not 10 min,
and dont tell your mom you used her good sink to clean your air filter.
lol. Ill be off to find a better video. Never having dont this before (new car) I new better than what you were doing. Atleast I learned the names of the products I need to go and get. fuck...
greatdane50 1 year ago
@greatdane50 It doesn't actually dry. It stays damp with oil, that's why it flies off and damages MAF sensors like it did with mine. Put a K&N in contact with a piece of cardboard and leave it for a few days, it will be saturated in the oil. I don't use them now as they do NOT filter to the standard of a paper element, so don't want to sandblast my engine with dirt the K&N allows through. K&N used clever marketing tricks and advertising, they still can't say how many microns they filter to!!!
urbex2007 1 year ago
youre supposed to rinse it from the inside out
and youre supposed to let the filter dry completly over night not in 10min before u put the oil spray
SFV818Si 1 year ago
is that a pokemon song. :D
aquateenI16 1 year ago
Holy crap! Thats one dirty filter....were do you live anyway?
If I were you I'd be cleaning it twice as often.
And always flush from the inside out or you will force any residual dirt deeper into the filter.
BMWLDRider 1 year ago
@BMWLDRider You seem to have contradicted what K&N claim about surface loading then, especially about the operation of what they don't say is a filter. People call them a filter so K&N go along with it, but don't say anywhere it filters - because it doesn't really. The K&N has a small surface area so wil block faster than a paper element with a 13ft surface area, K&N is 2ft max. So the holes in a K&N need to be 10 times bigger, allowing 10 times more dirt through than a paper filter. Bin it.
urbex2007 1 year ago
@urbex2007 Also. I would love for you to link me to somewhere that proves a K&N air filter functions worse than a stock air filter. The numbers you posted @BMWLDRider are confusing and don't make sense. Perhaps it was just your sentence structure. I personally know of a ~1000hp turbo car running a K&N filter with no ill effects. An open filter like this will not work for every car without proper tuning (Subaru STI for ex.) Do your homework and read directions before use.
nieldcaj 1 year ago
the cleaner smells like shit
theflyinhawaiian12 1 year ago
You should NEVER rinse the filter that way. you should always go from inside to out.
IgN1t3JB 1 year ago
After how many miles should I clean mine? And I have the filter thats exactly like the OEM filter but with the K&N fibers so is the process any different?
desimunda116 1 year ago
@desimunda116 Well, i clean mine every 10,000 miles. and i never tried to clean another washable filter with the K&N kit, but i would image it would work and it should be done the same exact way as in the video
zero2242 1 year ago
@zero2242 maybe im wrong but when I bought mine the dude said to do it every 3,000 miles or if it gets black which ever comes first.
rkoduke3d 1 year ago
@desimunda116 They say to at least check it every 30k miles, but it all depends on your driving conditions. I also have the drop-in replacement filter, and mine lasted about 25k-30k miles before it needed to be washed.
RaWxGuitarist 1 year ago
@desimunda116 you should clean it after ever ride
niedoba 1 year ago
can you blow dry it? or do you have too let it sit till it dries?
JImmyBTTP 1 year ago
@JImmyBTTP If you blow dry it you can harm the filter, according to the instructions the best thing to do is to let it sit and dry on it's own
zero2242 1 year ago
@zero2242 thanks
JImmyBTTP 1 year ago
Great video thanks. Just make sure you do it outside don't let that crap go to ur house pipes lol.
chchris25 1 year ago
wow im gonna clean mine too its been sitting there for 2 yrs
neonoxy 1 year ago
You are only supposed to rinse from the inside out, NOT the outside in.
nieldcaj 1 year ago
@nieldcaj Doesn't matter which way you clean it, is passes air both ways, the cotton isn't a one way system. This just shows the general lack of knowledge from people buying these devices. Learn about filtration, gasflow and save your money. If K&N filtered to anywhere near the standards of a paper element (which doesn't restrict flow) car manufacturers would use them, so would air conditioning companies. K&N have only scammed the boy racer market, the rest have common sense. K&N=no filtering
urbex2007 1 year ago
great video man thanks
dtenev2 1 year ago
good video just learned something
ecabrerad90 1 year ago
wow you musta had 150,000 KM on that filter or you live on a dirt road and tail people.
abi4life 1 year ago
alright might as well give it a try next time
miniwheats182 1 year ago
on the instrustions it says spray the clean side first
miniwheats182 1 year ago
on these cone air filter i had better results spraying the dirty side first then the clean
zero2242 1 year ago
Holy DIRTY filter batman
justintc93 2 years ago 18
Comment removed
FastbackJon 9 months ago
@justintc93 Maybe it's just all the excess oil he put on from the first time?
FastbackJon 9 months ago