CR500 Sportbike - Project Street Racer - Part 12

[JadedRockStar84]

That thing must be a bleeding ax murderer when it hits the power band with all the grip from those street tires! I love it! I'm also considering a CR500 motor for my shifter kart I'm about to start production on. 

[DuckmanCycles]

@JadedRockStar84 Thats what I'm hoping for, LOL! :) New video on Monday!

[v8vairv8vair]

i would fix the dents in that pipe. your losing power. also are you going to raise the gear ratios with this bike???

[DuckmanCycles]

@v8vairv8vair The few minor dents won't make that much of a loss to be noticable, they will be fixed more for cosmetic reasons than anything else, besides, I have 3 pipes.... and yes the ratio is already raised with the much smaller CBR sprocket in the rear, I may get a bigger front sprocket as well.

[DuckmanCycles]

@deej1478 thanks for your comment, now you're blocked for *sorta* just not getting it.

[TheKmk4420]

sweeeeet !!!! looking for word to the next vid bro 

[DuckmanCycles]

@TheKmk4420 Thanks, get a subby if you haven't next video should be up next week (I HOPE!) LOL! :)

[TheKmk4420]

this is killing me lol i wont to see this thing done and see some vid of it flying down the street hahah

[DuckmanCycles]

@TheKmk4420 I just got a radiator, its on the way here now! Once that is in order I should be able to start it.

[Blackdavid2011]

subscribed bro!

[DuckmanCycles]

@Blackdavid2011 I appreciate it! :-D

[groutaone]

Is it done yet? ha ha jk

[DuckmanCycles]

@groutaone Why yes it is! Think I can ride it across the border into Canada? :-D

[groutaone]

@DuckmanCycles Just make sure you keep your finger over the gas tank hole while you ride

[iiinverted]

cool build mate !!!!

[DuckmanCycles]

@iiinverted Thanks! I appreciate it!  Make sure to get subbed, new update on Monday!

[rob52965]

@DuckmanCycles cool as f##k roll on monday

[DuckmanCycles]

@rob52965 Recording now! :)

[carshowballer]

I love dirt bikes and rocket< great way to combind the two< great job man!!!

[DuckmanCycles]

@carshowballer Thanks! :-D More update on Monday!

[daVidFonda]

As far as the engine fits in this frame don't you think it would have been good to put some silent blocks between engine and frame to reduce the vibes and on the muffler too !

[DuckmanCycles]

@daVidFonda I thought about rubber mounting, yes. But the problem is, that allows the engine to move, and could cause a jackhammering effect thus SHAKING the bike instead of just some vibes. Secondly, when you get on the gas and the chain tightens up, the whole engine will twist in place and will cause chain alignment issues. So solid mount it is, a better approach would be to have the engine balanced properly! :)

[daVidFonda]

As far as the engine fits in this frame don't you think it would have been good to put some silent blocks between engine and frame to reduce the vibes !

[MrSanQuentin703]

BITE YOUR FACE OFF!

[DuckmanCycles]

@MrSanQuentin703 om nom nom

[MrSanQuentin703]

@DuckmanCycles its cool i never even started my cr project you got other videos im back into cars since i dont have a mclass autox civic coupe on the way ill post videos

[kikwear002]

when is this bike going to be done, its taking forever

last three minutes must be a band review

[DuckmanCycles]

@kikwear002 build your own, do it faster!

[mikasasaka]

@DuckmanCycles Lmao, good one :DDD

[DuckmanCycles]

@mikasasaka Besides, I need something to watch! LoL! :)

[kikwear002]

when is this bike going to be done, its taking forever

[bonzo9303204406]

are you PC genius or MECHANIC genius ... i dont know but i have the fealing that will be one hell of a cool bike .. even now looks gr8 i cant w8 till the end ... i will wach your videos to see what will happen to that cool project... i wish u luck with that thing and your business :)

[DuckmanCycles]

@bonzo9303204406 No genius, I just know what I want and what I like and I figure out the best way to meet htat goal, lol :)

[happywombatproducts]

Just a heads up, depending on the plastic you use...the plastic weld i did, did NOT hold well. You might be better off finding a plastic of the same consistency as of the tank, it stays together better.

[DuckmanCycles]

@happywombatproducts You missed what I said in the video! :-P I said I was going to use shavings and pieces from this tank to reconstruct it. :)

[happywombatproducts]

@DuckmanCycles Oh haha, my bad. I had music playing while i was watching this. BTW you are totally right about the deadline of this project, there is none! It's your project and your project only. keep posting videos!

[DuckmanCycles]

@happywombatproducts Thanks for the encouragement! :-D Keep watchin' and I'll keep makin'!

[happywombatproducts]

@DuckmanCycles yep, no problem :) cant wait to see that bike done. That's gonna be a good day.

[DuckmanCycles]

@happywombatproducts Well as I said in the video, it will probably never be done, LOL! I just wanna see it running and rocket down the street on it a couple times! :)

[happywombatproducts]

@DuckmanCycles Haha, i know what you mean, with such an exotic project there will be no ending. I too want to see that biek running, along with all the crazy, wild, shitty grins from everyone who sees a 2 stroke street bike of modern times.

[HELUVJEEPS]

Im Loving the DuckMan Cycles Page!....Im a fellow bike junkie!!...Im going to start making some videos of the stuff i do to my bikes!!....Keep up the great work!! TANK

[DuckmanCycles]

@HELUVJEEPS Thanks man! Excited to see your bike stuff!

[JoSeDbZcOoL]

i subbed just to see this project lol

[112mikee112]

Hey Glenn, how far ahead do you think when you are doing a project bike ?

do you just concentrate on one or two things that need doing next ? or do you have a million things whizzing around your head, and then change your mind ? ( ooohhhh I know what would look cool......oh no it wont work..!!!! ) ;-)

[DuckmanCycles]

@112mikee112 I usually don't. When I get an idea I start researching to see if it will work, often it won't rarely its already been MADE to work and I can spin off my own idea. But there is no time on this stuff.

[nicodanger13]

It's a sin you left the SV-CR project.. it was so sexxxxyy

[DuckmanCycles]

@nicodanger13 Well, I didn't leave it. I just switched gears. The SV is an SV650 once again, I just rode it to work this morning. The CR500 just got a new frame, but all the rest of the stuff I was going to use got used still (forks, wheels, brakes), LOL! :)

[nicodanger13]

@DuckmanCycles This model of SV is beautiful. I have a 2000 sv650 S , blue, a little modified. I love this bike but with a two stroke engine and maybe 30 kilograms less could be more funny!

[DuckmanCycles]

@nicodanger13 Yes that was the plan, I just had other issues with it that I didn't like. Such as kickstarter problems that I didn't feel like working with.

[MagicCadillac]

Well, that's anyway a cool project, no matter when it is finished, it is a cool project.

[spidez8407]

SWEEEETTT

[DuckmanCycles]

@spidez8407 I'm still lookin for that master cylinder, did FH have one? LOL!

[spidez8407]

@DuckmanCycles lol i havent seen him this weekend he's prolly sleepin off his weeken ill give him a call tommarow and let you know wuts up. ill send you a vid tommarow to make sure its the same kind. ill get back to you soon as i get ahold of that lazy sasquatch

[DuckmanCycles]

@spidez8407 Where's my vid tomorrow? lol! :)

[spidez8407]

@DuckmanCycles i knew i forgot something. Sweet Fudger!. i just saw ur comment a lil while ago. called him up and said he sold the motor and other components he said he let em take the whole thing. damn cheapskate