DIY Its work DoublerVoltage In12V to35V, out 24Vto 76V circuit fr. ElecFree com "search 12v to 24v dc to dc converter IC 40106, change BYWS1P1-200 to FT2000G n all the Capacitor into higher value, work very well together with PWM G Forrest Cook, all MosFeT using IRF250 w/Big Heat sink , 30Amp Max. for any HHO Cell thks :)) NO MORe Limited 12V fr. Car Battery or motifier Alternator, more volt less current, less heat :) for sure
Metal and iron works. Ft Collins CO. but they only had 304ss. If you want the 316L ss. you may want to check eBay there are a tone of great deals on there.
i have seen video's where people have done tests with alternating holes... it did not solve the problem. some of the problem is within each individual plate's holes. i did rebuild the big cell this way and it did change my mmw. Not a hole lot though. I have more tests to perform.
The only way to prove this is by doing 2 tests , one with the insers and the other without...this test should include the same electrolyte and the amps production should be recorded for both...less amps more output is what we are all tring to achieve
David, no offence , but I think you might be defeating the purpose with those 3/8 inserts.
Current flow will take the path of least resistance .If all the holes are aligned together some current will travel straight from neg to pos thus bypassing the neutrals.The edge of the holes are conductive and so are the sides,If you seal the edge of the holes the current will simply flow to the sides of the plate. If you stagger the holes from one plate to the other you will overcome leakage.
you are doing some great work with these designs ... its so nice to see more and more of this type device showing up on YouTube ... most all of started out with the wall plates and whatever else we thought might work ... it is gratifying to see how much this technology has progressed in just the year or so I have been watching folks do this on YouTube ...
thank you for your contribution to the effort ... wonder if Tero Ranta had any idea a couple years ago how far his design would go ...
thank you. I have many tests to do before i truly celebrate! No on the 316l.. I wish but could not afford it. it is 16 gage 304 ss. Thanks for viewing.
Thanks.. so how do i go about doing that? is it just to check the amp gage? or to fined how many amps i am running? How would i go about that accurately?
buy an auto fuse holder and a variety of fuses if on your amp meter you see 5 + amps put a 5amps fuse and se if it blows if not after a30 45 minuts go lower 4 amps this is how you can double check your Amps
thanks i see how that would work! But i just got a clamp on amp meeter and i could not read this one right. though i think the gage was good i just could not accurately read it. My mmw is 5.35 but that is in a small cell. I will see what the big one does when i re build it. i did a final test with the new amp meeter right before tear down and it ran a consistent 5.44 mmw so hopefully that will increase. but i think that will be the real test of it. Thanks for your advice it is always welcome
i am working on getting the money for a good amp meter.. this one is hard to read. i feel like i am guessing on what my actual amps are. though this is the very same one i used for my previous tests. I found one at harbor freight for like $60. I am thinking of selling my old test cells for the money.
thanks! but i am noticing as i up my currant i lose mmw... I think it is because of how thin i had to shave my nylon grommet's. I think the higher currant is able to jump threw them and cause some leakage currant. Further tests need to be done to conclude this. It may be that my battery has been charged to much and it can not perform higher. that may be why the big cell did better when i used the car charging system. how is your no hole cell coming?
It is coming alright , waiting on some tubing I ordered me and tjgame2 have been collaborating on the idea..If everything goes as planned will have it running this weekend..I going a diffrent route than what I posted,I think it will that way I just dont have the tools to do precise machining, so I am taking another route ..
well at least you got me to view your video. lol . good work, keep going
MrPhillerup 1 year ago
DIY Its work DoublerVoltage In12V to35V, out 24Vto 76V circuit fr. ElecFree com "search 12v to 24v dc to dc converter IC 40106, change BYWS1P1-200 to FT2000G n all the Capacitor into higher value, work very well together with PWM G Forrest Cook, all MosFeT using IRF250 w/Big Heat sink , 30Amp Max. for any HHO Cell thks :)) NO MORe Limited 12V fr. Car Battery or motifier Alternator, more volt less current, less heat :) for sure
Drdump1 2 years ago
can i ask where you buy your gasket material? thx
delvis11 3 years ago
the ones in this cell i got at home dep.
David7900 3 years ago
This has been flagged as spam show
What did you use for gasket material between the cell plates?
partwerks 3 years ago
40 mil shower liner. but i cut 2 gaskets per gap.
David7900 3 years ago
im looking to build a cell where did u get your stainless from thanks
cricketol 3 years ago
Metal and iron works. Ft Collins CO. but they only had 304ss. If you want the 316L ss. you may want to check eBay there are a tone of great deals on there.
David7900 3 years ago
sorry my posting is back to front
bhelpurii 3 years ago
i have seen video's where people have done tests with alternating holes... it did not solve the problem. some of the problem is within each individual plate's holes. i did rebuild the big cell this way and it did change my mmw. Not a hole lot though. I have more tests to perform.
David7900 3 years ago
The only way to prove this is by doing 2 tests , one with the insers and the other without...this test should include the same electrolyte and the amps production should be recorded for both...less amps more output is what we are all tring to achieve
regards
bhelpurii 3 years ago
David, no offence , but I think you might be defeating the purpose with those 3/8 inserts.
Current flow will take the path of least resistance .If all the holes are aligned together some current will travel straight from neg to pos thus bypassing the neutrals.The edge of the holes are conductive and so are the sides,If you seal the edge of the holes the current will simply flow to the sides of the plate. If you stagger the holes from one plate to the other you will overcome leakage.
bhelpurii 3 years ago
Shouldn't you check the voltage out put of your 12volt with out a load , mine is 14.5 that changes my mmw alot.
tjgame2 3 years ago
i never thought of that. how do i factor that in??
David7900 3 years ago
Never mind man . You are 100% on this I didnt know and that is my fault. And nice work man . You got me started on my current build.
tjgame2 3 years ago
you are doing some great work with these designs ... its so nice to see more and more of this type device showing up on YouTube ... most all of started out with the wall plates and whatever else we thought might work ... it is gratifying to see how much this technology has progressed in just the year or so I have been watching folks do this on YouTube ...
thank you for your contribution to the effort ... wonder if Tero Ranta had any idea a couple years ago how far his design would go ...
SmartScarecrow 3 years ago
Thank you so much for your kind words! And encouragement!
every new thing i learn raises a new question! I need to invest in real test equipment.
David7900 3 years ago
spent the money on a clamp on amp meeter... bad news.. no surprise to most though. 5.3 mmw
David7900 3 years ago
Good job, great efficiency! I like your solution to leakage. You are one smart guy.
Is the plates 316l ?
Bob Campbell
HHO4gas 3 years ago
thank you. I have many tests to do before i truly celebrate! No on the 316l.. I wish but could not afford it. it is 16 gage 304 ss. Thanks for viewing.
David7900 3 years ago
use a fuse instead of the amp meter that you have till you get the money to buy a clamp on ac/dc amp meter ,nice work
najman100 3 years ago
Thanks.. so how do i go about doing that? is it just to check the amp gage? or to fined how many amps i am running? How would i go about that accurately?
David7900 3 years ago
buy an auto fuse holder and a variety of fuses if on your amp meter you see 5 + amps put a 5amps fuse and se if it blows if not after a30 45 minuts go lower 4 amps this is how you can double check your Amps
najman100 3 years ago
thanks i see how that would work! But i just got a clamp on amp meeter and i could not read this one right. though i think the gage was good i just could not accurately read it. My mmw is 5.35 but that is in a small cell. I will see what the big one does when i re build it. i did a final test with the new amp meeter right before tear down and it ran a consistent 5.44 mmw so hopefully that will increase. but i think that will be the real test of it. Thanks for your advice it is always welcome
David7900 3 years ago
WOW that is a good!!! mmw do you have a different amp meter I have ben working on MMW on my cells great work!!
ssfuturescott 3 years ago
i am working on getting the money for a good amp meter.. this one is hard to read. i feel like i am guessing on what my actual amps are. though this is the very same one i used for my previous tests. I found one at harbor freight for like $60. I am thinking of selling my old test cells for the money.
David7900 3 years ago
6.87 is very good mmw I have tried so many thing in the holes I have all so tried no holes on bottom. my mmw are in the low 6 on alot of me cells.
ssfuturescott 3 years ago
I still have lots of test to do before i celebrate. i seem to get a great deal of mmw drift from low to higher amp. I will keep people informed!
David7900 3 years ago
Pretty good results man ..
jdcmusicman 3 years ago
thanks! but i am noticing as i up my currant i lose mmw... I think it is because of how thin i had to shave my nylon grommet's. I think the higher currant is able to jump threw them and cause some leakage currant. Further tests need to be done to conclude this. It may be that my battery has been charged to much and it can not perform higher. that may be why the big cell did better when i used the car charging system. how is your no hole cell coming?
David7900 3 years ago
It is coming alright , waiting on some tubing I ordered me and tjgame2 have been collaborating on the idea..If everything goes as planned will have it running this weekend..I going a diffrent route than what I posted,I think it will that way I just dont have the tools to do precise machining, so I am taking another route ..
jdcmusicman 3 years ago
i look forward to it! I think your rout is going to work better than mine! Good luck to you!
David7900 3 years ago
I have high hopes but you know how that can go sometimes , thanks
jdcmusicman 3 years ago
yes i do.
David7900 3 years ago
use q tip plastic tubes .
najman100 3 years ago