EVIKE.COM - Disassembly Guide for Echo 1 MOD-5

[ZombiePeppers]

FUCK!



[shortyjk95]

Ok can make another vid on how to take the bolt apart Aka the part that you pull on to show the hop up cuz mine broke and I don't know how to take it off, mine has a pin thing not a screw and the pin I can see all the way through it

[DannyBoy465]

i have taken out every visible screw and body pin the selector switch and all that and am down to my upper and lower. I cannot get them to slide apart though the motor is out everything is out they just wont slide apart. Any help?

[shortyjk95]

Dude my mp5 comes apart way differently

My gearbox once stock is off can just slide out after the pin by the mag is out and then the barrel and hop up just slide out

How do you take off the charging handle, Aka the thing u pull back on that little knob thing

[dftrent95]

would this guide be the same for the cm049? im asking because it has a version 3 gearbox

[weq7]

the metal mp5s are a hell of alot easier. just remove the pins the motor and 2 screws and your done, only plastic mp5s are this complicated.

[uav741]

I have an Echo 1 Mp5a5, and there is a plastic cover over the hop up and there is a screw there, and I cant move the cover, please help.

[weq7]

but also what kind of screw is in the selector switch i dont want to strip it pleeeeeeezzzz respond.

[airsofter43]

my cyma fm mp5 is alot easier!

[BLARG0868]

This will work for the marui mp5k right?

[AirsoftNoob94]

believe me- fort minor <3

[mongoosedawg]

Man, I am so not getting an MP5 now...

[MrAirSmith]

all i wanted to do was change the barrel... not anymore...

[NYPLAYA05]

Do you guys have a video on how just to changing the barrel without taking the whole gun apart

[GrandpaChink]

My Lower receiver wont come off can sme one help me please  Thank You

[GFAQsBlarg92]

@GrandpaChink

I had the same problem... after you pull the motor out, check behind it for a plate with two screws. Once I unscrewed those, my lower receiver came off.

It took me almost 30 min to figure that out. You cannot imagine the facepalm when I finally noticed those screws.

[airsofter991]

iws there an easier way to only replace the barrel because i don't thiink i could do this without breaking it!

[TheDredRed]

This thing is about as difficult as the m14

[footballcomp57]

does it have a metal gearbox?

[TheSexytaco69]

what was that song in the begining

[PVTSilvia]

you think this is complicated, try an M14

[mikeya1236]

This is why I love my G&G. 3 push pins and the motors screws and the gearbox is out. Not nearly as complicated as this.

[inufan530]

Holy shit! MP5's are way too complicated. I'm sticking with my M4!

[SGThartman762]

@inufan530 M4's are probably the simplest airsoft guns that I do tech work on, Mp5s, and G36s are a tad more complicated. Even SAWs are easier, in my opinion.

[ThoraniosX]

"Be careful not to break the rubber."

So true, so true. A life lesson indeed.

[Zayk54]

@ThoraniosX LOL

[ooopppiikkk]

didnt they make a ez er way to dissemble this?

[LAGUNA76229]

@ooopppiikkk ya

buy a plastic one, throw it at a tree, do what you got to do, buy a new PLASTIC receiver, repeat

[YoshiLover2012]

this is by far the hardest to dissasemble lol

[TheLakerfan97]

can you take the mag apart?

[drdrew169]

i have released all of the screws, but the lower reciever wont come off. any suggestions?

[TheEarthwalker]

they forgot to say remove the two phillips screws inside the motor grip

[drdrew169]

the ones holding the motor cover on?

[TheEarthwalker]

negative, once the motor is removed, there are two screws inside the grip that hold the grip to the gearbox, they're next to the holes where the wires come out

[drdrew169]

did not see those. thanks!

[I2robinsyano]

i fix it already.. it was the MOTOR became loose..don't know why..but i believe i fixed it.

[I2robinsyano]

k this is what i have from EVIKE JG Matrix MOD5 A4 RAS Full Metal Full Size Airsoft AEG Rifle + Free Red Dot.

[AEG_JG_MOD5A4RIS] pls help.

[I2robinsyano]

by the way...my gears are making noise...i believe its dis-alined..kindly pls help...

[I2robinsyano]

k..i have the jg ris mod5..am still fighting on disassembleng my metal gear box...is not easy to tink on this video..pls help..i followed the steps on this video..but gearbox not come out...pls help.

[jonnyboiboi]

what kind of MP5A4 is it???

i am trying to help my friend to downgrade the spring, but i need to know which gun brand is it.

[InvokeZero]

Wow, and I thought airsoft guns were simple to disassemble.... (rethinks getting an MP5 possibly...)

[soccerstr05]

i would suggest a p90 for cqb (thoguh the mags are tough to find and if you are outdoors go m16 or aug

[InvokeZero]

yeah, I have owned and used both the 90 and m16, P90 is your best bet for CQB but can get spendy since mid-caps are the only solution to the P90's horrid feeding problem, and for outdoors I prefer a G3 SG1 or G36E

[soccerstr05]

the problem with the g36 is the barrel is pretty small and the extended versions look terrible

[InvokeZero]

not really, if you use the versions without the integrated scope and use an Acog, they look pretty cool IMO because of that, and the E variation with a C-Mag and integrated bipod with an Acog is one of the best looking guns I have ever seen. You want ugly? Look at the Type 96 Chinese PLA rifles, those are FUGLY

[FLYBOYDC]

It's easier than taking a M16 apart.

[AirsoftMilitia]

i am now not going to but any cheap mp5 im going ca or G&G

[LazyWaffleman]

wow that looks like a pain in the a** my mp5 takes down with one pin XD