HobbyWing EZRun 13T / 35A BL combo run & impressions (PART 2)

[MrOswaldo15]

hey you guy should test a leopard and a tacon bl motors. plz i want to see the results

[UltimateRCnetwork]

@MrOswaldo15 I have tested Leopards and Tacons. Reviews are on my channel.

[reizp]

im looking to go brushless on my ecx circut what motor and esc combo should i use on it



[vctmas]

so is it good for the traxxas stampede,rustler and slash all two wheel drive???i really want to know asap....thanks e-mail me at vctmas@yahoo.com or reply at my youtube account vctmas thanks again for the info....

[facebiter]

Yup, good video

[Everythingsellz12]

yo is this bettrr than the venailon system

[bosskake702]

your logo reminds me about subway.... eat fresh

[bigborekit12]

Nice I just got one to its a 5.5 t and that thing rips in my blitz vid sooon

[CsxDanny89]

Can someone please tell me if this motor is good for 1/10 drift cars ?

[ilikeginetta]

does it have lipo cutoff?

[REALMRCGOD666]

ive got a Tamiya M-01 mini it only has 21T spur thats its limit can i mod it to a 23T on my motor im confused i think

[REALMRCGOD666]

anyone know how you use 11-12 ?? i think its a misprint

[UltimateRCnetwork]

@REALMRCGOD666 Those functions just aren't available in this low-end ESC. They were used on some of their more expensive units.

[REALMRCGOD666]

@UltimateRCnetwork

Thanks can u use like a 9T on a 35A ?? or is the 13T motor its lowest limit ?

Thank you again

[JTJG94]

Were you using a lipo?

[thermalzz]

Herold and Kumar.

[TheStealther]

Jang. Can you review the HobbyWing EzRun 5.5T 50A Brushless combo? its almost 160$ tho

[djarov1997]

lol for 50paunds you can get 5.5t 6000kv 60A combo from ebay :X

[mrDarksand]

what where the run-times you got from this combo? and with what battery?

[mrhamfishrc]

i have got the 5.5t and it is getting hot with a low gearing.. What should i do.

[jmloudon97]

@mrhamfishrc get a heat sink with a cooling fan on it, you can find them on ebay

[36POINTBLANK]

my first step into brushless was an 8000kv mamba on 3s lipo...not too smart xD

[BeastOnCallOfDuty]

what's the amp draw on your last test

[lilddesignsrc]

can u put 3s lipo in it? i put 3s in it and the esc roasted in about 3 min the motor lasted a couple of days then the shaft can unglued it says it can handle 3s

[Tigerbarb202]

Hey just a random question, if I were to lengthen the wires on my velineon esc would change the timing?

[nerdyrcdriver]

my friend therustyfisherman has the 60amp version of the esc. He runs a 3s most of the time. The fan was fine. But then he broke a fin on it and the fin then cut on of the wires going to it. He took the fan off and it still runs cool.

[G0xPRO]

hey jang, would a velineon and that speed control be a good setup, thanks shoot a comment back if ya got the time

[Cyborg1170]

I am wondering what does changing the motor timing do. Is it like changing the gearing in the motor.

[ps3gamer143]

Please sell a urc body for the slash 4x4 on ebay but im from uk so sell it to the uk plz

[trxultimakx09]

should i get this or the dynamite fuze system?

[titi989]

how fast can it go????

[yoyomaster5203]

can you use that in a electrix rc circuit?

[THEkrazyBOY2596]

what does the timing do?

[kawasaki6697]

is are those stock slash rims with proline dirt hawgs?

[rcguy8038]

Yo Jang is the 35a fine for racing or should I go with the 60a esc?

[TheKoolNerd1]

I'm getting the 12t with a 11.1v lipo. Do you think that it will go faster than the 13t with the battery you used?

[mattio79]

this setup is best for people that want to eliminate ONLY the maintenance issues with brushed setups

[keeton520]

hey jang can you please make video on how to program it without the program card i cant find a video anywhere on how to do that thanks thanks

[sickipods]

Hey man I have a problem with my 35a ezrun esc, I think it overheats and just shuts off for about 20seconds then comes good, a green led flashes on the side of the esc when it stops working. I'm not really sure how to fix it, any ideas??

[mc47981]

@sickipods

Are you running nimh batteries ?

[xXDINOKINGXx]

how do you change the motor rotation on the motor because mine spins the wrong way so i need it to spin the opposite direction and reverse is now foward and foward is now reverse. i have already tried changing the th.cont on my transmitter and doesnt realy help i do have the programing card but it wont allow me to use item 11 and 12

[UltimateRCnetwork]

@xXDINOKINGXx Swap any 2 wires.

[rapejaambelgufie]

¡Great reviews!

[meamjustme]

You can run the ESC with a 8 cell without changing the fan. Never failed here.

Now i run it on 3s lipo's. Changed it then. 9T motor in a onroad car. After 2 batteries, a 2 and 3 s , both 5700 mah. I can still touch it. It is warm. Not hot. Same goes for the esc.

[TheHuntingTerminator]

Do you have an opinion on the Leopard ESC and motor combo also sold at hobbypartz??? They look decent, can you help me out here??? Thanks, and great rc vids and reviews on stuff!

[SECustomRC]

Have you had any problems with this speed control? Ive heard a lot of folks who have had problems with these in the past.

[meamjustme]

I run mine on a 3s.

Tt01 though. And i did need to change the fan. But after testing the original fan i found it would fail at 20 volts XD

Really cant go wrong for the money!

[MrPicaldy]

Hi Jang, have you tried the 9t motor on 2wd?

[paultraxext]

what battery are you running? thanks jang

[shikakae123]

What other good points does this motor have?

[shikakae123]

I intend to get a brushless motor.However,I see different motor like 5.5T or 32T.What are the difference between the T?Does it determine the speed or anything?Which will be better?Higher T or lower T?

[shikakae123]

What is the difference between the 13 T and the 32T

[dtxfan]

@ Jang  What gearing did you run in the slash ?

[UltimateRCnetwork]

@dtxfan I believe it was 23/90.

[staticxmako]

please test a higher amp ecs and lower kv motor in a e-maxx

[dtxfan]

Great Job. Your gonna have to try the xe-run esc next.

[purplelambo95]

how come this thing is so quiet and mine is really loud and clankety i still am not sure if i set the gear mesh correctly and ive seen the how to video and gear meshing is just not my thing im afraid if i go to loose ill strip a spur and if i go to tight ill ruin my new brushless arrrg!

[2testtest2]

i'vr just gotten the 60A/8,5T combo in my gravelhound. So far I'm very pleased with the power. on 6cell NiMh it does almost 50kmh with the stock gearing and GPS straped onto it. However Iæve had some problems with smal rocks jamming the fan. When that happens ESC temp goes from 40C to 70C+ (I stoped when I saw this). That was Quite hefty running on loose sand though, It does not usually get that hot.

[wupperRC]

You measured the temperatures. But is there anything like a suggested maximum temperature at which a brushless,or brushed motor performs best,without overheating?

[UltimateRCnetwork]

@wupperRC Usually 160 degrees F is about as high as you want to go for general bashing & practice. If you're racing you may push it higher, but 180 or higher gets you into the danger zone where the magnets may start to lose strength over time.

[ethanissocool]

@UltimateRCnetwork Or perhaps puts you on the highway to the danger zone.

[beabiker]

yeah i got the basic same except it was another chinese brand all it did was overheat even with a 6 cell nimh pack!!!!! then it finally burst into flames

the motor is actually pretty nice good for like hour long run times with a better esc

[xj39eldiablo]

I have a 60amp 8.5T combo which has a true 540 motor on my slash and it's great for what it cost . the esc is excellent , it survived getting dragged 3 laps around the track when the servo tape came undone with just the fan getting a blade broken also it's always fairly cool. the motor however isn't that great but then again think about the modest price.

[frogs84ss]

it also states right on the website that that motor is for onroad beginners. for 97 bucks theres a 4000kv motor for off road it's an 8t motor i think a much better test for the slash and still under a hundred bucks

[UltimateRCnetwork]

@frogs84ss The folks who write such general statements as "for intermediate off-road" or "beginner on-road" use aren't talking to experienced RC'ers. What matters is not those ambiguous statements, but rather the actual power output and usable range of the system. As I noted in my unboxing video, I very specifically & consciously chose this system because I WANTed something of modest power, NOT something overpowered, for a specific reason.

[frogs84ss]

in my opinion the 3000kv is pretty low even the traxxas brushless is 3500kv. so i think with i higher kv motor you'll get much better performance.

[UltimateRCnetwork]

@frogs84ss There are many factors that go into determining the actual power of a motor. You can't simply go by kv. For example, Traxxas' 3500kv motor has about the same power, if not higher (depending upon the version), as the Castle Creations 5700kv motor. What makes this EZRun 13T motor modest so in power is the small rotor. High-kv motors are difficult to impossible to gear in the Slash, so the best fit is simply something physically larger.

[JRockz08]

couldn't you have left the timing alone and went more on gearing for more top end?

[UltimateRCnetwork]

@JRockz08 With the kv as low as it is, you're probably right, just gearing up and staying at 15 deg. of timing may have allowed the motor to run more efficiently at peak RPMs and squeezed another mph or two out of it.

[Slovflyer]

Great review! I'm using my first "budget" brushless ESC, a ZTW 60A that does sensored motors too. I ran it with 3S lipo as well as 2S with a 2700 Kv Feigao 9L in my Slash (great performance), and for kicks on 3S with a Hacker C50 3600 Kv in my Emaxx. Yup, it survived, if only because I ran it cautiously. The little fan probably saves its life more than anyone could imagine.

Let's see that x.5 turn system review soon!

[asbar23]

soory man but u tried one AND THE MOTOR GAVE UP ON ME WHEN IT WAS RUNNING LIKE 145 AFTER A MONTH SO I PRETTY MUCH HATE THIS youll see the motor wont last but i am ok with the esc

[STdemoniac]

I hear what Ez-run motors 9T and + use the same rotor as in a 380 size motor, only 9T and less use normal rotor ;-)

can identify folow corps, if it flat then ok (like my 5.5T ezrun system) , if corps same like in u vid (corrugated), then rotor 380 size ...

cheers

[UltimateRCnetwork]

@STdemoniac Yep like noted in my unboxing video, this one is very clearly and obviously the small size rotor with large cooling fins. I'll probably try an __.5T system next.

[STdemoniac]

@UltimateRCnetwork i think try 9T my self, some 9T motor coming with small rotor, some with normal size ( I think) :D

[chuqyv12]

cool video, I just got the exact sytem and it works great.

[zagonielod]

Have you tried ever the 100A/5200kv sensored brushless combo from hobbyking? Or have you heard anything about it?

BTW! Appreciate your good work here. One of my favourite channels on youtube :) Cheers!

[UltimateRCnetwork]

@zagonielod No experience with that system yet This was my first "cheap" brushless system :) With the experience I've had with it so far, it definitely won't be my last.

Thanks for your kind feedback!

[dizzyinzo]

i bought that system and the first week i had it the esc went out, i bought the 60a esc and that worked really well, but then the motor went out so i am not have alot of luck with this system

[UltimateRCnetwork]

@dizzyinzo What kind of temperatures were you getting with it?

[dizzyinzo]

@UltimateRCnetwork i did have some thing to accuratly test the temp but ill guess some were around 170 on the motor and the esc never got hot the first one and the second one

[RCNEWStv]

cool vid

[rcdevil2]

thanks for making these two vids, haha now im gonna get the HobbyWing 5.5t 6000kv motor and 65 amp esc ;) i hope you have fun with your set up!

[SmallDragon76]

Nice Testing. It sounds like a realy good beginners system, espacialy for that price.

Is HobbyWing the manufacturer or is it only a brand mark? Would be interesting to know if I can get this here in germany.

Looking forward to see there " high-end" systems tested by you.

[UltimateRCnetwork]

@SmallDragon76 HobbyWing is the manufacturer. HobbyKing (note the 'K') is the best place to shop for them, I think, as they have a warehouse in Germany. There are also many eBay sellers based in China that will ship to Germany.

[fredburger130]

would you recomend this in a hpi wheely king?

[UltimateRCnetwork]

@fredburger130 I think for light-duty use or if you're going to gear it down plenty, it would be a good match with a bit more power than the stock motor. You can get a slightly higher-end EZRun system though if you want to go noticeably faster, or one of their slower motors for slow-speed light-duty crawling.

[fredburger130]

@UltimateRCnetwork very cool thanks

[EndoCloudz]

can you use a 3s lipo on it?

[UltimateRCnetwork]

@EndoCloudz I mention that late in this video and talk about it in more detail in my unboxing video. With this particular combo I wouldn't try it. I'd get one of their better combos for 3S.

[hchia17]

It was great when it work right but the 35a is just way to low for all of my batteries that has a 25c bust

[fabiodacunha]

The only problem with the Ezrun 13T and also 9T its that they say that is 1/10 scale motor 540 size motor, but actually its a 380 motor with 540 can. that sucks.

So the Ezrun 8.5T (4000kv) its the true 540 size. i think that will be the best Ezrun motor for short course

[UltimateRCnetwork]

@fabiodacunha Yep I showed that in the unboxing video. For my next test I'll try one of their __.5T systems and at least a 60A ESC.

[GetBlitzified]

Awesome review! Great job!

[208BMAN208]

ANOTHER great review! Im running a Hobby Wing system in my crawler (you know!), but I am unfamiliar with "timing changes". Could you or anyone else reading this, please point me in the direction of some literature on that subject?! So far my system hasnt failed me at all, I hope yours holds up for you and im really looking forward to seeing what this system is going in!!

Your the man JANG, URC#1

[UltimateRCnetwork]

@208BMAN208 The simple way of putting it is that more timing gives you more RPMs and top-end power (and higher amp draw up top), up to a point, but less torque down low. It works like the timing advance on a gas engine's distributor -- as motor speed goes up, you need some timing advance for things to fire soon enough.