i think it bull shit this guy never showes yoy all of how to instull things just so u people know go to cbtiicks it will show u every think there this guy is from coustom cb watch out he likes to volt the finels
@waterlooguy1 Let's see how can I explain this... My videos are NOT instructions on how to, they are informational on what I have done and the results. If I did how to videos then I could not make my living doing this.. Next, this is how you spell Custom not coustom and finels is spelled finals. Volting MOSFETS is just fine as you are taking the load off the regulator and this keeps the radio cooler. Also some manufactures do this from the factory so it can't be all bad no can it.
You have no idea what you're Talking about. Go ahead and find on CB tricks on how to install an sc2290 in a dx959... He has done 2 radios for me and they run very clean and the finals are not volted. Why don't you go check out Radioactive Radios for a SWP, you will love that! LOL. BTW, where did you learn to spell?
ive been into cb/ham for 40+ years and seen alot of radio shops and had my own radio repair shop in the 80`s and you do some great work no wires all over the place and looks like crap, but you do a awesome job my freind, keep it up
Raging husky...obviously you don't understand what happens when audio is applied to this module. the carrier rises along with the audio, so the splatter and overmodulation you allege isn't there. Do your homework first.
All I can tell you is the radio sound great on the air and it is no worse that most of the tuned radios out there. If you leave the limiter in the radio you still have control and you have great sound.
It might be a little wide but so are most CB Radios.
Nice work on getting that rig upgraded with the amp! by the way, can you mention if this could be used as a replacement to install it in an hr 2510? that would be awesome for all of us who have a 2510 with the MRF477 final busted!! i personally have 3 of them with that problem..
Well I have talked on it for over an hour and got nothing but great reports. The scope is not perfect sine wave but it does have round corners, and you have the ability to turn it do more if need be. A lot of this can be taken care of from biasing.
How could this radio produce a good scope pattern? With a 2 watt key and peak power of around 90 watts the radio would have to be massively over modulated. Should be set to around a 20 watt key to be clean but still loud.
I know that is not what the swing crowd wants to here but i myself hate an over modulated distorted sounding radio and with that much forward swing there is no way the scope pattern could be considered good.
obviously, you dont understand the function of a driver and final. if you did, you would know they dont create or modify modulation. please dont tell people what you dont know.
Except that the dead-key level you see on your meter IS FROM the final output... NOT the driver. Stop selling snake oil; DK 2 swinging 90 is a blown out, over modulated splatter box that will sound like ass... Put a low pass filter in front of that meter and let's see what the wattage is. I'm betting a lot of it is 2nd and 3rd harmonics...
i think it bull shit this guy never showes yoy all of how to instull things just so u people know go to cbtiicks it will show u every think there this guy is from coustom cb watch out he likes to volt the finels
waterlooguy1 1 month ago in playlist CB Radios
@waterlooguy1 Let's see how can I explain this... My videos are NOT instructions on how to, they are informational on what I have done and the results. If I did how to videos then I could not make my living doing this.. Next, this is how you spell Custom not coustom and finels is spelled finals. Volting MOSFETS is just fine as you are taking the load off the regulator and this keeps the radio cooler. Also some manufactures do this from the factory so it can't be all bad no can it.
cbrepairguy 1 month ago
Comment removed
owentimo 1 month ago
This has been flagged as spam show
@waterlooguy1
You have no idea what you're Talking about. Go ahead and find on CB tricks on how to install an sc2290 in a dx959... He has done 2 radios for me and they run very clean and the finals are not volted. Why don't you go check out Radioactive Radios for a SWP, you will love that! LOL. BTW, where did you learn to spell?
owentimo 1 month ago
great video
boricua6326 4 months ago
cb repair man, what is your handle in Terre Haute? I talk to Terre Haute from Indy time to time.
scott231us 1 year ago
hi how is your day im jason .have dowen a dx 88 or a corba 25 ltd think for your vedo
cbboy73 1 year ago
so can I ship mine for you to install the RFX-75?,,its fresh back from a warrenty repair, havent touched it since
wepoppimpin 1 year ago
i want one installed on my dx 959
wepoppimpin 1 year ago
how about a dx959? same procedure? thanks. by the way, do you intall if i ship mine
?
primotote 1 year ago
that was a real 92W
1112223333111 2 years ago
If it's swinging to 90 watts the dead key should be around 22 watts for a clean pattern.
Tazor41 2 years ago
beautiful install. :)
neubie182 2 years ago
could you please show the scope pattern? i would love to see how great that much modulation must look.
great job!
bspn33 2 years ago
2 watts swing to 90 watts is going to look like trash on a scope and sound like it on the air as well!
THEBEASTOFOLD 2 years ago
yea i was trying to see if he would just show it. hahahahhaah
bspn33 2 years ago
could you install it in a galaxy 959 radio
marksweet09 2 years ago
ive been into cb/ham for 40+ years and seen alot of radio shops and had my own radio repair shop in the 80`s and you do some great work no wires all over the place and looks like crap, but you do a awesome job my freind, keep it up
bunker2k1 2 years ago
Thank you... I do try .
cbrepairguy 2 years ago
can the rx75 be mounted to any CB radio not just new ones?
bunker2k1 2 years ago
It can me mounted to most radio with some work.
It has to fit on the back, so make sure you have the space.
cbrepairguy 2 years ago
what mode of operation that put out the 90 watts?
and what do you get on SSB?
tcarver007 2 years ago
You get about the same on SSB as well. Mabe a little more but nothing big.
cbrepairguy 2 years ago
Raging husky...obviously you don't understand what happens when audio is applied to this module. the carrier rises along with the audio, so the splatter and overmodulation you allege isn't there. Do your homework first.
hibuckhobby 2 years ago
All I can tell you is the radio sound great on the air and it is no worse that most of the tuned radios out there. If you leave the limiter in the radio you still have control and you have great sound.
It might be a little wide but so are most CB Radios.
cbrepairguy 2 years ago
nice job
control2980 2 years ago
Thank you.
cbrepairguy 2 years ago
Is the 93 watts peak or rms?
meangreen69Nova 2 years ago
Peak
cbrepairguy 2 years ago
Thats an awesome piece of kit
darynsax 3 years ago
Hello CbRepairguy!
Nice work on getting that rig upgraded with the amp! by the way, can you mention if this could be used as a replacement to install it in an hr 2510? that would be awesome for all of us who have a 2510 with the MRF477 final busted!! i personally have 3 of them with that problem..
samalayork 3 years ago
It could be done but you would have to deal with the heat sink on the back of the radio.
cbrepairguy 2 years ago
Thanks for sharing the information with us Doug...Bulldog!
BLUZUMR 3 years ago
Well I have talked on it for over an hour and got nothing but great reports. The scope is not perfect sine wave but it does have round corners, and you have the ability to turn it do more if need be. A lot of this can be taken care of from biasing.
cbrepairguy 3 years ago
How could this radio produce a good scope pattern? With a 2 watt key and peak power of around 90 watts the radio would have to be massively over modulated. Should be set to around a 20 watt key to be clean but still loud.
I know that is not what the swing crowd wants to here but i myself hate an over modulated distorted sounding radio and with that much forward swing there is no way the scope pattern could be considered good.
THEBEASTOFOLD 3 years ago
beastofold,
obviously, you dont understand the function of a driver and final. if you did, you would know they dont create or modify modulation. please dont tell people what you dont know.
chip3655 2 years ago
Dude you just got bitch slapped by chip3655!
gotveggieoil 2 years ago
Except that the dead-key level you see on your meter IS FROM the final output... NOT the driver. Stop selling snake oil; DK 2 swinging 90 is a blown out, over modulated splatter box that will sound like ass... Put a low pass filter in front of that meter and let's see what the wattage is. I'm betting a lot of it is 2nd and 3rd harmonics...
raginghusky 2 years ago
Don't get all bitchy with me...I just stated that fact of the bitch slapping....
gotveggieoil 2 years ago
The carrier voltage and the carrier rises as the signal is modulated. do your homework before you start spouting about splatter and low pass filters.
hibuckhobby 2 years ago