@c00k13m0nst3r7 And you're a dipshit who cant spell and wastes his time posting drivel. I am on a diet, have you found any smart pills yet? Last I heard, you cant fix stupid.
@almost6879 'Lipo Ready' is assumed to mean that the guns insides are strong enough to handle the extra speed and power of a Lipo battery. A cheap gun with an 11.1v Lipo battery in it will run so fast and hard that if you held the trigger down too long the gun will self destruct very quickly. If it's got strong metal internals and good wiring, then you can think of it as Lipo ready.
@axeman3d i bought this gun aswell to upgrade and its really nice only problem is that most sights have 350fps limmit and this gun is already 350fps so if u put a 6.03 tightbore barrel in (like i did) u are gonna have to use which .25g which is good in a way as they will fly straighter but they are a lot more exspensive! and i put magpul stock and front end on (magpul moe parts u probs know about them?) and i changed the upper reciever to a metal APS one and the magwell and know the mag fit fine
@SeigeAirsoftUk I too have replaced the stock parts with Magpul parts, the body with metal upper and lower, new hi-speed gear set and better spring. Mine shot 325 fps, but the limit on the site I play is 370 so a bit more power for the forest sites suits me just fine. I use .25 BB's all the time for accuracy, but they will show about 30-40 fps lower on a chrono. Sites will chrono with .20's, using heavier BBs wont get you past that without lying.
@SeigeAirsoftUk really? where do you skirmish? i skirmish at xsite airsoft and they allowed me to be chronoed with .25g but no higher ? and yours chronoed and 325? fair enough then and i also play in forests, i also wouldnt reccomend a lipo in this gun, it will shred the gears, but i beileve you said you changed yours, so that is okay, i also might be buying a tokio mauri hop and hop bucking which will make this gun very nice, and also what i found dispointing was the frnt sight is not removable
@SeigeAirsoftUk The limit is technically 1 joule of energy, which could be 500 fps with .10s or 230 with .40s. Most sites around me use 350-370 fps limits with .20s and request single shot at close range. The indoor CQB site has strict 330fps limits. I used an 11.1v lipo and what failed was the trigger contacts, which got scorched by constant single shot at the CQB site. The gears were fine, and the trigger contact just needed cleaned.
@SuperXKato If you like it, go for it. They're too slim for me to hold comfortably, but shoot well. The TM ones were very well built, not seen many others around. It does mean buying SIG mags as well, not as easy to find as M4s, AKs, etc and the clips on the side for joining mags together get in the way. They catch in pouches and take up more room.
@airsoftalex100 It's not high quality, but for the price it is really good. The parts are pretty well made, but assembly and wiring leave a bit to be desired. I finally killed mine with tons of single-shot CQB rapid fire with the 11.1v battery. It got red hot and finally the internals seized up. Had to happen, so I am fitting better gears, spring and a new metal body to it now.
if you want a gun with good externals get a g&g full metal,classic army full metal, or kwa, its a sportline... SPORTLINE what do you think a kwa is a sportline and this is an lpeg
your right it is plastic but its a very high grade polymer! in fact there is a video on airsplat of a guy hitting his with a hammer and it doesn't break. Its just wobbly not cheap!!
@heynow114 If it costs less than half the price of other M4s, its technically cheap. The original sliding stock on this fell to bits during a game, and while replacing it i found the stock tube had not been screwed together properly either. The wiring is a very thin gauge as well, with cheap connectors in it. Its all over cheap, but it works.
@axeman3d what i mean was that the polymer its made of wasn't cheap i wasn't really talking about the rest of the make up. I did just get mine in the mail today and I see what you mean about the stock. It seems to be made out of a completely different kind of plastic then the rest of the plastic parts.
@heynow114 The catch and spring in the stock fell to bits quite quickly, so the rest just slid off. If you dont check, tighten and even glue all the screws, it might fall to bits at any time. I swapped them out for Magpul parts right away, tightening parts as i found them.
@mu5t11 In the UK you can only purchase a RIF (realistic imitation firearm) if you are 18, a member of a recognised, insured airsoft club or site, or hold a UKARA number. Basically you need to sign in on a proper site at least 3 times within a 2 month period then fill out a form. Some places sell 'two tone' guns, painted bright colours to avoid the law. It's illegal to repaint them if you have no license.
@mu5t11 A quick Google shows about 14 in and around London. Go join Arnies Arisoft forums and ask in there, it's the biggest airsoft discussion forum by far. Lots of locals to help point you at the right place. I do know a CQB site in a disused shopping mall opposite Reading train station. Firefights in a real shopping mall, you cant beat that.
@MarshyTheMagicMan Thanks. Next up will be a Magpul stock and then probably the metal replacement body. Ebaybanned have some nice cheap options there.
@axeman3d this is cheap but it is a high end gun buddy itz has a higher qulity then any jg or ca and e1 out ther for the fration of the price so no wat u are talking bout
@XxXscorpionXninjaXxx Compared to my Tavor, a Magpul Masada or a Systema this is a very low-end gun. This gun costs the same as a replacement barrel for a Magpul Masada, a quarter the cost of my Tavor and one tenth the cost of a Systema PTW. It rattles like a bag of bolts and creaks like a sailing ship in a gale. It's low-end. It's by no means bad, but not brill. Also you need to work on your writing, I had to reread it several times to try and make sense of it.
@XxXscorpionXninjaXxx did you even watch the video? He said (and demonstrated) that the externals are...not the best, but said that internally it's perfectly solid. Our friend Kenny isn't a commercial reviewer, if he though this gun was shit he wouldn't have bought it.
Your a fatt ass
c00k13m0nst3r7 3 weeks ago
@c00k13m0nst3r7 And you're a dipshit who cant spell and wastes his time posting drivel. I am on a diet, have you found any smart pills yet? Last I heard, you cant fix stupid.
axeman3d 3 weeks ago 2
@c00k13m0nst3r7 lol hater
paytonfritz 2 hours ago
yes im beginner but what does lipo ready mean and whats good about it?
almost6879 6 months ago
@almost6879 'Lipo Ready' is assumed to mean that the guns insides are strong enough to handle the extra speed and power of a Lipo battery. A cheap gun with an 11.1v Lipo battery in it will run so fast and hard that if you held the trigger down too long the gun will self destruct very quickly. If it's got strong metal internals and good wiring, then you can think of it as Lipo ready.
axeman3d 6 months ago
@almost6879 lithium polymer just in case your still wondering :P
Bludman4Gaming 3 months ago
is this a good beginner gun?
UrbanK1llerz1 7 months ago
@UrbanK1llerz1 I think so. It's cheap, light, tough, reliable and easy to upgrade or add to. For the money these are nice rifles.
axeman3d 7 months ago
@axeman3d i bought this gun aswell to upgrade and its really nice only problem is that most sights have 350fps limmit and this gun is already 350fps so if u put a 6.03 tightbore barrel in (like i did) u are gonna have to use which .25g which is good in a way as they will fly straighter but they are a lot more exspensive! and i put magpul stock and front end on (magpul moe parts u probs know about them?) and i changed the upper reciever to a metal APS one and the magwell and know the mag fit fine
SeigeAirsoftUk 7 months ago
@SeigeAirsoftUk I too have replaced the stock parts with Magpul parts, the body with metal upper and lower, new hi-speed gear set and better spring. Mine shot 325 fps, but the limit on the site I play is 370 so a bit more power for the forest sites suits me just fine. I use .25 BB's all the time for accuracy, but they will show about 30-40 fps lower on a chrono. Sites will chrono with .20's, using heavier BBs wont get you past that without lying.
axeman3d 7 months ago
@SeigeAirsoftUk really? where do you skirmish? i skirmish at xsite airsoft and they allowed me to be chronoed with .25g but no higher ? and yours chronoed and 325? fair enough then and i also play in forests, i also wouldnt reccomend a lipo in this gun, it will shred the gears, but i beileve you said you changed yours, so that is okay, i also might be buying a tokio mauri hop and hop bucking which will make this gun very nice, and also what i found dispointing was the frnt sight is not removable
SeigeAirsoftUk 7 months ago
@SeigeAirsoftUk The limit is technically 1 joule of energy, which could be 500 fps with .10s or 230 with .40s. Most sites around me use 350-370 fps limits with .20s and request single shot at close range. The indoor CQB site has strict 330fps limits. I used an 11.1v lipo and what failed was the trigger contacts, which got scorched by constant single shot at the CQB site. The gears were fine, and the trigger contact just needed cleaned.
axeman3d 7 months ago
@axeman3d oh okay i might use my mp5's lipo in it then :D
SeigeAirsoftUk 7 months ago
@SuperXKato If you like it, go for it. They're too slim for me to hold comfortably, but shoot well. The TM ones were very well built, not seen many others around. It does mean buying SIG mags as well, not as easy to find as M4s, AKs, etc and the clips on the side for joining mags together get in the way. They catch in pouches and take up more room.
axeman3d 8 months ago
@axeman3d dude it may be cheap but this a high quality gun made from g&G
airsoftalex100 8 months ago
@airsoftalex100 It's not high quality, but for the price it is really good. The parts are pretty well made, but assembly and wiring leave a bit to be desired. I finally killed mine with tons of single-shot CQB rapid fire with the 11.1v battery. It got red hot and finally the internals seized up. Had to happen, so I am fitting better gears, spring and a new metal body to it now.
axeman3d 8 months ago
@axeman3d dude it better then classic army sportline , jg , echo1
airsoftalex100 8 months ago
u guys ship to canada
SgtTriggerHappy 8 months ago
if you want a gun with good externals get a g&g full metal,classic army full metal, or kwa, its a sportline... SPORTLINE what do you think a kwa is a sportline and this is an lpeg
XxBioElementxX 9 months ago
@XxBioElementxX or vfc
XxBioElementxX 9 months ago
vfc
XxBioElementxX 9 months ago
Comment removed
XxBioElementxX 9 months ago
your right it is plastic but its a very high grade polymer! in fact there is a video on airsplat of a guy hitting his with a hammer and it doesn't break. Its just wobbly not cheap!!
heynow114 9 months ago
@heynow114 If it costs less than half the price of other M4s, its technically cheap. The original sliding stock on this fell to bits during a game, and while replacing it i found the stock tube had not been screwed together properly either. The wiring is a very thin gauge as well, with cheap connectors in it. Its all over cheap, but it works.
axeman3d 9 months ago
@axeman3d what i mean was that the polymer its made of wasn't cheap i wasn't really talking about the rest of the make up. I did just get mine in the mail today and I see what you mean about the stock. It seems to be made out of a completely different kind of plastic then the rest of the plastic parts.
heynow114 9 months ago
@heynow114 The catch and spring in the stock fell to bits quite quickly, so the rest just slid off. If you dont check, tighten and even glue all the screws, it might fall to bits at any time. I swapped them out for Magpul parts right away, tightening parts as i found them.
axeman3d 9 months ago
hi there m8 do u need any lience or membership to purchase this gun thank you
mu5t11 9 months ago
@mu5t11 In the UK you can only purchase a RIF (realistic imitation firearm) if you are 18, a member of a recognised, insured airsoft club or site, or hold a UKARA number. Basically you need to sign in on a proper site at least 3 times within a 2 month period then fill out a form. Some places sell 'two tone' guns, painted bright colours to avoid the law. It's illegal to repaint them if you have no license.
axeman3d 9 months ago
@axeman3d thank you m8 do u no any airsoft skrimish clubs in london cause iam having trouble finding one please can you help me out
mu5t11 9 months ago
@mu5t11 A quick Google shows about 14 in and around London. Go join Arnies Arisoft forums and ask in there, it's the biggest airsoft discussion forum by far. Lots of locals to help point you at the right place. I do know a CQB site in a disused shopping mall opposite Reading train station. Firefights in a real shopping mall, you cant beat that.
axeman3d 9 months ago
You aint my Uncle D:
llXxKhaosxXll 10 months ago
@llXxKhaosxXll It's 'Uncle' in the sense of your auntie's live-in lover.
axeman3d 10 months ago
@axeman3d It wasn't serious haha(:
llXxKhaosxXll 9 months ago
Uncle kennyyyyy!
xxRiidDl3dSn1p3rxx 10 months ago
i love youre accent
FuzorDragon480 10 months ago
Everything shakes cause u bought the crappy version. Lol
Napolean2001 10 months ago
@Napolean2001 You're sharp, kid. I can see very little gets past you.
axeman3d 10 months ago
ha You said it was a clone.
It is actually G&Gs attempt to compete on the same market as the clones.
and so far It seems like its holding up.
all of G&Gs products are pretty high quality even if they are cheap The plastics they use for the body are a Nylon Fiber weave type material
but the rest im sure are the standard ABS
Overall I plan on buying one of these too
Thanks for the vid
cmzangetsu1993 1 year ago
great review! I'm getting this gun very soon, and im going to follow the upgrades on this gun. your giving great ideas!
MarshyTheMagicMan 1 year ago
@MarshyTheMagicMan Thanks. Next up will be a Magpul stock and then probably the metal replacement body. Ebaybanned have some nice cheap options there.
axeman3d 1 year ago
@axeman3d this is cheap but it is a high end gun buddy itz has a higher qulity then any jg or ca and e1 out ther for the fration of the price so no wat u are talking bout
XxXscorpionXninjaXxx 1 year ago
@XxXscorpionXninjaXxx Compared to my Tavor, a Magpul Masada or a Systema this is a very low-end gun. This gun costs the same as a replacement barrel for a Magpul Masada, a quarter the cost of my Tavor and one tenth the cost of a Systema PTW. It rattles like a bag of bolts and creaks like a sailing ship in a gale. It's low-end. It's by no means bad, but not brill. Also you need to work on your writing, I had to reread it several times to try and make sense of it.
axeman3d 1 year ago
@axeman3d okay but u dont no dude this is a high gun just itz plastic doesnt mean itz shit come man g&g does not make low end guns
XxXscorpionXninjaXxx 1 year ago
@XxXscorpionXninjaXxx did you even watch the video? He said (and demonstrated) that the externals are...not the best, but said that internally it's perfectly solid. Our friend Kenny isn't a commercial reviewer, if he though this gun was shit he wouldn't have bought it.
fearthegeeklord 11 months ago
@fearthegeeklord externals are pretty good there made out of nylon fiber and thats pretty strong
XxXscorpionXninjaXxx 11 months ago
@XxXscorpionXninjaXxx that doesn't contradict what I said.
fearthegeeklord 11 months ago
@fearthegeeklord okay he said extenaly is nylon fiber is a petty good plastic very durble plastic
XxXscorpionXninjaXxx 11 months ago
@XxXscorpionXninjaXxx neither does that.
fearthegeeklord 11 months ago