How To Install Lightup Thumbstick Mod Kit for Xbox 360 Controller from Modjunkiez

[zGibbinzModz]

i want that solder tip !!!

[xXDeadWreckeningXx]

I have the Old Matrix TP19 Controller. can this Thumb stick Mod Still Work?

[Modjunkiez]

@xXDeadWreckeningXx Yes it will work on old matrix controller

[XXC0DQUICKSN1P3RXX]

thanks awesome tut they work great install was pretty easy. i pressed lt sync to turn them on

[BigSebs]

how do u turn them on!!!!!!!!!!

[marchingtrombonist1]

I've seen this question posted but couldn't find an answer, this was for a matrix board. How do we now what we have? And when you finished was it ready to go?

[marchingtrombonist1]

I've seen this question posted and couldn't and answer. 1 this was for a met

[burningangel1000]

okay i just got the crome v2 can i set the controller up with out that metal shit? If not where can i get some?

[TheJacx2000]

do they work on a slim controller

[Modjunkiez]

@TheJacx2000 Yes they do work with a slim controller.

[allaire74]

What solder gun u using

[Modjunkiez]

@allaire74 Weller WLC100 Adjustable Power Soldering Iron.

[xXChrisss]

Can you use this and the Scorch 7 mode chip int he same controler. will they fit with both?

[northerner94]

i have the same problem as @Raidas4life12, wot do i do

[Modjunkiez]

@northerner94 It sounds as if it isnt grounded properly or a loose solder point

[JKDspirit]

the way u said "we sell em for 29.99 was SOOOO AWESOME!!!

[Dana6400]

once this is complete do u just put the controller together and should u all work???????

[mrLCPink]

How can you tell what type of controller you have?

[Modjunkiez]

@mrLCPink got to the guides section on our website and check under scorch rapid fire installation there are diagrams that will show you the difference in cg and matrix boards.

[itsalwaysallie14]

i did it

[pbb3ast]

Instead of using solder can i use a super glue to keep it down? please answer

[Modjunkiez]

@pbb3ast We do not suggest using super glue it will destroy your board and possibly your controller.  Please use solder and a 30 watt soldering iron

[TheMrShredability]

can you do this on a wired controller?

[michealowns21]

i cant figure out the sync connect

[RazorX313X]

Wired Controller?

[CHRISObradley]

So, just clearing up. On a CG you solder the 4 points, with the last one being the sync button? So do i not have to worry about the 5th point?

and is it necessary to solder the the led's to the actual thumbsticks or is it just to hold it in place?

thanks

[exliger6]

Is it possible to connect this to the rumble motor with rumble dome?

[Raidas4life12]

hello i was wondering if i could get some help installing this. I soldered all the points but only the red led's come on when I turn it on?

[Modjunkiez]

@Raidas4life12 We responded via your CRM Request on the website. Thank You

[cbabaseball148]

is that wire you are holding with the soldering iron

[Modjunkiez]

@cbabaseball148 no that is solder in the other hand comes coiled in tube. Please let us know if you have any further questions.

[montville96]

what is the best soldering gun please pm me a link or respon with a link



[ComCliniC]

thanks for making video for this im ordering this week

[netweit3]

Hey I was wondering if it was better to get a higher voltage soldering gun. Should I get 40w? 60?

[kingtut469]

@netweit3 The best I think for things like this is 30-40w. Too many watts can damage the circuit board.

[Modjunkiez]

@netweit3  30 Watt would be the best.

[m0dman360]

@netweit3 agreed 30 watt is best. good guide

[CODModdRZ]

good video tut!!