Esky Transmitter Problem / NEED HELP!!!

[felixthemaster1]

you need to turn on the tc and then turn on rx really fast

[Peanutdinos3000]

Did you use the bind?

[jandlejandle]

you need to install bind plug in receiver then power up and put transmitter into bind mode . bind plug can go into battery slot and power up through throttle always make sure signal white or yellow wire is pointing in toward main receiver body

[vattenskoterchaffor]

Also check this video and try if it gets better :)

search for: Technical Support-- To unbind and rebind Tx of Esky Helicopters @RC-Fever.com

[elmardus]

Did you already solve the problem? Do you know what it was? I have excactly the same problem, and now I don't know what do do.

[fukufukusylar]

@elmardus

hi mate.

No, i have not solved this problem yet. i think the problem is in the TX itself.

still finding a solution for this. will let u knw if i find 1.

ok?

[vattenskoterchaffor]

@fukufukusylar

But the main question is if u have tryed to start the TRANSMITTER BEFORE u plugg the batterie in???

That should be the right order to start it in to get it to connect to eachother.

[elmardus]

@fukufukusylar I have sent the transmitter back, and there was no solution. The shop was very kind, and they sent me a new one, even though my warranty was expired... : - )

Good luck, I would just send it back to the shop, or get another, better TX....

[limguar69]

open screw and unplug socket change the tx small board circuit antena because the electronic cannot funtions perfect.

[fukufukusylar]

@limguar69

open screw and unplug socket change the tx small board circuit antena ????

can u show me what board please????

[alishanmao]

Just try to rebind the radio to receiver. hopefully it will settle the problem

[myshlongdong]

mostly all transmitters should be ternd on before the reciever and you should hav fully charged batterys some allso try rebinding

[ricksternz]

hey mate i got same problem, after i put 4x 2100mah batteries. Did you put 2000+mah batteries on this one too before the problem started? I cannot fix mine too and it's beautiful weather out to play :(

please reply if you found solution to this..

[alexandervotyakov]

You must turn on transmitter first, and then receiver.

[Jokusenpoika]

You sould put your transmitter on FIST.

[1963hasse]

Hi. i don´t know if you still has this problem, i had a similar problem.

and it was that throttle was on almost 100%. so i revers the channel.

and it works.

[SHAUN269]

your first problem is that you brought a esky product dumb ass

[crackerms0100]

@SHAUN269 hmmm

[chrismechanic2000]

whenever you are dealing with ANY model, allways turn on the transmitter BEFORE you connect the lipo to your car/heli/plane etc...good luck nickos no flying here in england today its too windy for a king 3...

[Sakumiku]

i have had an esky hunter for about 2 weeks it is rubbish a complete rip off, it struggles against the slightest breeze, it wont go above 30 feet, the blades are very brittle dont waste your money on this like i did.

[machokb]

I have the same problem the TX led is blinking also the RX, do you find some solutions for this

[Speed070107]

I also had problems binding the TX to the RX and I noticed another problem.

When you switch the TX on, the red light, left below on the TX should blink very fast for a couple of seconds. If the led on the TX blinks slowly, or not at all, then the battery power is below approx. 5.5 volt, and you need to replace them.

The critical point where I have binding problems is in my case 5.47 volt or below.

Hope this helps.

[rollingstonedev]

Similar problems: Rx connect to LiPo = steady but faint light inside Rx. Power-on Tx = fast flashing the red LED on Tx, then solid red. This is supposed to mean "Tx and Rx bind OK." Correct? But I get no 2-tone signal, nomatter what I connect to the Rx (gyro, some servo's, ..)

Simple question: what is that micro-switch inside the Rx for? (press with long fine object, not sharp) I press that, nothing changes.

My dealer can't help me. I'm on my own.

Thanks for your help.

Stefaan

[OgoldM]

Some tests later, the TX is still not binding. What does a NOT blinking LED at the TX say?

Does the TX need to unbind first?

THX

[OgoldM]

I just bought a transmitter with the no. EK2-0406G on the back. The transmitter runs on 4 AA-Batteries which made me think that it could also bet he EK2-0406J, because it also has silver applications on the front while the EK2-0406G is just black.

When I try to bind, the RX (EK2-00424) is blinking slowly, which says, that it is ready to bind. The manual says that no switch is necessary to hold. Just switch the power of the TX on.

The TX-LED is lighted solidly, no blinking like in the video.

[fukufukusylar]

for this to bind.

1. on the TX

2. connect the battery to RX ( Really fast after oning the TX )

thts how i did the binding

hope it helps

[OgoldM]

What does the TX, when it's unbind and you switch it on? Does it blink, or is the LED solid?

When the binding process is successful you the TX becomes solid, but what happened before?

My RX is always slowly blinking, even when I switch the TX on....no contact to the RX.

[OgoldM]

What I figured out so far is, that I bought a transmitter EK2-0406G, but it takes just 4 AA-Batteries. It also has siver applications on the front side, so that I guess it could be the EK2-0406J. (Correct me if I'm wrong!)

The manual says, that the rebinding process is just switching the RX on first and the TX later. Without holding any switch. When the RX blinks slowly it is ready to bind.

What about the TX-LED, does it have to blink too?

Thanks

[fukufukusylar]

yes, for about 15sec it should blink, really fast

[vespaboy692000]

just wana ask if your Tx has a trainer switch? try something there were you can press and hold or tuggle up and hold when you turn the power on.. blinking light tels you that its not binded to the Rx..

[fukufukusylar]

for ur info. in these TXs there is no need to hold down the trainer switch. cos i have tested my heli wit another TX. and it binds and work perfectly. so the TX in this video is broken i couldn't fix it.

ITS A TX PROBLEM,

[OgoldM]

Hello there from Germany,

I have some similar problems like you've shown in your video.

My receiver blinks constantly and slowly since I pressed the receiver-button to unbind it.

Now I want to rebind the receiver to the transmitter, but even it I follow the user manual correctly I can not succeed.

The only difference I have is, that the transmitter-led is not flashing. I have a constant light there.

Hopefully someone can help!

[bbwever]

did you ever figure out how to solve this problem? mine is doing the same thing now.

[Redblood797]

same here. Dont want to waste more money on a new tx.

[helipilot94]

you have to hold down the trainer switch in order to bind.

[NightFlyyer]

Does it need a Binding Plug. I dont have one to test, but my spectrum will not enter the bind mode, unless I hold the trainer switch on while I turn on the tx. In the case of binding, The tx may need to be turned on first. Blinking means it is not bound. Make sure throttle hold, 3d switches are off and throttle stick and trim lever is also all the way down.