Buck Converter HHO Update

[H2Truckers]

Are you going to us a wetcell or a drycell after you are dun with your testing?

[irondmax]

@H2Truckers

pipes all the way.

i have another test to run to see what spacing i want on my pipes, these you see are 1/8 spaceing........toooooo far.

i want to end up with 20 or 24 inches long. 9 sets.

meyers said the pipes are better because heat is controlled by the shape at the end of the pipe. also the wire connection should be at the bottem. this aids in the voltage burst out the top.

also i have a theory about something meyers did not say,but i noticed in his video. noone else sees it

[H2Truckers]

@irondmax Pipes are good, Have you looked in to nickel pipes I have seen them at home-depo for about $35.00. HHOPOWER made some goog steps with it (nickel) and I think that with your buck converter it will work very well.

I am going to buy the parts to build a buck converter like yours I think you did a good job on it thou I will use dual mosfets.

[irondmax]

@H2Truckers i found a supplier that has most sizes availible any length. 304 or 316 stainless. stainless is mostly nickel.

i will check though.

still not decided on my gap.

i used the relays because no fan needed to cool them. and if they go bad. easy to replace. plus i think points give a much sharper power spike.

also relays will work for pos and neg. and if i want say 200 amps....i just add more relays. still no fan needed.

if you need clearer circuit diagram let me know

[H2Truckers]

@irondmax Ok yes I would like a diagram on how you do it cus I have ben using a ATX power on the 5.5v at 15 amps .

I have a no curent los dry cell that I have ben working on.

[irondmax]

@H2Truckers

its the same as i posted here.

youtube email me your other email. i will send a clear schematic and help.

its easy to build. i made it that way..... and give it freely....so everyone could join in.

[poprock4me]

very impressive your work mr. irondmax . your buck converter is sucessfuly producing hho in 4 volts ? one of my friends mr. vox tell me about your channel ,

i sell pwm to him that i replicate pwm from delvis11 . but when i saw your buck converter work i impress . my pwm power is not enough to say powerful like your

buck converter project . if you dont mind mr. irondmax , can you help me to replicate your buck converter too?

[irondmax]

@poprock4me

yes no problem.

what would you like help with first?

the 4 volts is not so important......the inductor is the important.

i made mine from 100 turns of 12 gauge house wire, with the insulation rubber still on it. then another 100 turns over that. its made from 19 low carbon welding rod, flux removed then one wrap of black tape around each rod. bundled together one wrap of tape around the bundle.wrap the wire neatly left to right. over top to under

[poprock4me]

@irondmax Thank you very much sir for the information . yes about the inductor

thanks .

[irondmax]

@poprock4me i will check rod diameter and number for you tomorrow.

you can try you pwm with the inductor.

i think its best to use the irf chip to drive 2 car relays. you can drive the pos and neg wires that way, or you can add more relays and inductors for more amps.

easy to go from 5 amps up to 200 amps.

if something melts it will be the relay.....cheap fix.

i have many more ideas for this circuit......many more

[poprock4me]

@irondmax i am not familiar about the irf chip , is this a mosfet ? how about

irfp260 mosfet . . later i will buy haft kilo of copper wire gauge #12 , then follow your

instructons , the only i need ampheres i think to increase maybe until 10 amps or 15 amps , because my battery is only 5 amps for my scooter . is it possible for 3 volts we can raised the current more than 10 amps . i post last nigth im using 5 amps battery then direct connect to pwm to cell , i start to 5 amps ,

[irondmax]

@poprock4me irfp260 46 A .

should be good.

irf640 is 18 amps.

you should figure your length of wire. important not to splice it.use pie R squared x 100 turns. then add a little. 2 coils also.

less amps carried means you can use smaller wire if you like. but mine seems to work well, good idea to do that way.2 colars wire for 2 coils , solid wire not , NOT,stranded.and rubber insulated. we call it romex. for the house.

[ThePresidentialTouch]

Saweet! This is exactly what I was looking for, though I didn't know until I saw it!

Oh, and Desertphile says "It doesn't work!! It can't work!! Even though I'm seeing it perform with my own eyes, It still won't work!! It never can!! Your all morons!!! I'm the best!!! I rule all with my great wisdom and superior knowledge to all of you other little people!!!HAHAHAHAHAHAHAHAHAHAH­AHAHAHAHAHAHAHAHAHAHAHAHAHAHAH­AHAHAHAHAHAHAHAHAHAHAHAHAHAHAH­AHAHAHA!!!!!!!!!!!"

[irondmax]

@ThePresidentialTouch sometimes the little people win out.

Desertphile cracks me up.

every will see......it does work.......and i will prove it.

[ThePresidentialTouch]

@irondmax Hey, when the planets line up, if God sees a bankshot, will he use "English"?

[irondmax]

@ThePresidentialTouch no he would just wave his hand.......it would go anywhere he vwanted

[H2Truckers]

I LIKE IT,I LIKE IT!!!

[irondmax]

@H2Truckers try it

[H2Truckers]

@irondmax This is just what I need for a stepdown from 12v to 6v.

I like it cus it will piss of Desertphile and his dumb-ass budys.

[irondmax]

@H2Truckers try it......if you need help..... let me know

[H2Truckers]

@irondmax Ok I will so if you can PM me for some help I will like it.

[hhoforvolts]

Looking good, nice HHO production, excellent progess.

Richard

[irondmax]

@hhoforvolts thanks

[Ace011mm]

Very very nice! I must try to replicate...

[irondmax]

@Ace011mm i will help you if you want to replicate it

[Ace011mm]

@irondmax Thanks,when I find free thyme I do. Keep good work!

[irondmax]

@Ace011mm do what i do.......make time......

if i did not need to sleep or eat........i could do so many things.

[Ace011mm]

@irondmax  :)

[vox1philippines]

W O W !!!.... looks like a advance engineering for HHO projects....

i like your inductor.....

[irondmax]

@vox1philippines thanks Vox