Thanks for your exerlant video ! I just got the 168 V2 with flaps - It has no pre drilled holes for wing or elevator ! Did yours ? You says yes ? What motor and prop did you use ? How many Cell Lipo ? Many thanks i need help !!
@OzParkPilot servo position,the brushless is a NTM 35-48 900KV two lipo turnigy nano-tech 4400mah 65-130C in series you have some volt 14.8 but double mah 8800 for a good flight time a
turnigy 3 blade propeller 10x7,and a turnigy trust 70A esc with is programming card where you select 16k
switching frequency, medium timing,accelleration high,brake off,low voltage detection stop motor,
if you need nuch help e mail me p66charly@tiscali.it
@OzParkPilot all wing holes are covered by the grey film, you can push the wing with the finger slowly
,and where it became soft there are the hole, in my fpv 168 long range built tutorial ( 1 ) i explain this ,i think you see only tutorial 2 ,i suggest put the elevator and rudder servo in the foward side not in the tail section in this way your model became a
little bit light ,you don't need put lead on the nose to compesate tail
@p66charly - Many thanks for you reply you help alot already !! My wing has no hole for screws ;-( but elevator yet so I can go off there. I shall look at tutoriel 1 and email you if I have question which Im sure I have. Many thanks - Ciao !
@som3x ,uso una spektrun dx 7 ma anche per me più o meno il limite è quello,puoi aggiungere sulla trasmittente un antenna direzionale "patch antenna"il cono di irradiazione
è di circa 140 gradi non 360 cone quella standard,io non l'ho mai provata vedi sul sito hobby king nel menù categorie Telemetry - FPV - FrSky Telemetry
thanks for your help!
karlosio1 3 weeks ago
Thanks for your exerlant video ! I just got the 168 V2 with flaps - It has no pre drilled holes for wing or elevator ! Did yours ? You says yes ? What motor and prop did you use ? How many Cell Lipo ? Many thanks i need help !!
OzParkPilot 1 month ago
@OzParkPilot servo position,the brushless is a NTM 35-48 900KV two lipo turnigy nano-tech 4400mah 65-130C in series you have some volt 14.8 but double mah 8800 for a good flight time a
turnigy 3 blade propeller 10x7,and a turnigy trust 70A esc with is programming card where you select 16k
switching frequency, medium timing,accelleration high,brake off,low voltage detection stop motor,
if you need nuch help e mail me p66charly@tiscali.it
p66charly 1 month ago
@OzParkPilot all wing holes are covered by the grey film, you can push the wing with the finger slowly
,and where it became soft there are the hole, in my fpv 168 long range built tutorial ( 1 ) i explain this ,i think you see only tutorial 2 ,i suggest put the elevator and rudder servo in the foward side not in the tail section in this way your model became a
little bit light ,you don't need put lead on the nose to compesate tail
p66charly 1 month ago
@p66charly - Many thanks for you reply you help alot already !! My wing has no hole for screws ;-( but elevator yet so I can go off there. I shall look at tutoriel 1 and email you if I have question which Im sure I have. Many thanks - Ciao !
OzParkPilot 1 month ago
@OzParkPilot i will send to you some photo that show the hole position send me your e mail at p66charly@tiscali.it i will send all you need
p66charly 1 month ago
Nice model but so tail heavy its unreal!
Austinpowers46 1 month ago
@Austinpowers46 yes you say right,in my next model i will put the servo in the nose side
in this kit the servo mount are located in the tail section and at the end of assembly i will add some lead on the nose 250gr about
p66charly 1 month ago
Motor and prop looks nice
RcLento 1 month ago
Ascoltami; ma per la trasmissione tx e rx, che usi? io ho una aurora 9, pù di un km non va come posso fare?
som3x 2 months ago
@som3x ,uso una spektrun dx 7 ma anche per me più o meno il limite è quello,puoi aggiungere sulla trasmittente un antenna direzionale "patch antenna"il cono di irradiazione
è di circa 140 gradi non 360 cone quella standard,io non l'ho mai provata vedi sul sito hobby king nel menù categorie Telemetry - FPV - FrSky Telemetry
p66charly 2 months ago
Better landing gear? Eagletree/FPV followup? Very helpful vid. Thanks!
luftschiffe24 4 months ago
the plane looks nice. seems to be real smooth.
roelwieggers 7 months ago
you should do a vid on ur fpv system
jwjwjwjwjwjwjwjjwjwj 7 months ago 2