Briggs and Stratton compressed air conversion (BUILD and FIRST RUN) PART 1

[vqlive]

ahhh good try Now new project for you m,ate , I made a air compressor out of a twin 200 cc honda once cylinder ran the other had a hose stuck in sparkplug hole it worked great about 29 years ago

[doubleboost]

good lad enjoy your self

nice to see interest like this

[pcblah]

it uses more elcetricity then it produces :P nice set up though...

[Cytacon]

The ignition coil is causing resistance. It would run a lot smoother and start off easier if you removed it.

[brendonv101]

@Cytacon Watch other run video. I removed it.

[Andyhgn53k]

@Cytacon Don't you guys think that a Wankel Engine would convert to air a little easier?

Just a thought

Regards

Andy

[josephdupont]

Very nice conversion..Any more enhancements?

Have you tried steam??

[andrew100dukw]

I was going to do this but I was thinking the air would force open the intake valve all the time. How much pressure do you think that valve spring can hold back?

[brendonv101]

@andrew100dukw The valve spring will hold back about 120psi or so before it lifts. Lap the valves to increase pressure. Run a test and see once you make the inlet fitting and add heavier springs on the intake side if it lifts to early.

[dragata1]

hey new name for it the bubble engine or the fart engine

[Stanleyguy101]

good luck with that making sure cylinder has oil and crankcase has oil will help so will fixing that timing, which you have a plan for. I have a steam bicycle, but I am trying to get running correctly myself.

[brendonv101]

@Stanleyguy101 I have another video of it running better. I put oil in it and changed the timing and ground the cam a bit.

[brendonv101]

@DeeJayMiikkii Alrighty sweet. Do u happen to go to the force raves? Ahh small world.

[brendonv101]

@DeeJayMiikkii Nah thats me haha.

[bmxmatte1]

way the fuck do u destroy a nice engin to make som lame air motor that barly runns?!!!!!!!!!!!!!!!!!!! and admit that it sucks

[brendonv101]

@bmxmatte1 Well i think its cool. Also, i got about another 20 or so engines so idk.

[Stanleyguy101]

@bmxmatte1 He said the engine is already not running at the start of the video if you were listening and that engine is not attached to anything.

If a conversion is done right a 5 cu engine a bigger version of his can allow you to go 40 mph on a bike.

[ford1979truck]

put a muffler on it see if it sounds any differt

[geoff390]

how did you weld brass to steel?

[brendonv101]

@geoff390 Its steel not brass. Luckily haha.

[geoff390]

Oh i just thought it was because of the colour.

[FreezEntertainment]

at 3:48 did u say "and....bobs your uncle"

srry, i had to ask haha

[Cchange4us]

hey next time just make the engine run reverse and screw a pipe into the exhaust hole for air delivery but anyway great just

[porche3r]

whats better 2-stroke or 4-stroke?

[brendonv101]

@porche3r Well 2 stroke all u gotta do is whack ur air in ur spark plug hole and it goes. BORING! 4 stroke u gotta modify the cam which takes ages to perfect i must add so its essentially a 2 stroke. Then u have to make a air fitting where the carb use to go to its a bit more tricky.

[roastingpeanuts]

2 stroke......

[porche3r]

cool nice

[fordmanmad]

cool

[bmx1994mathisen]

nice