G&G GR-16 Takedown

[artura2011]

i am trying to get a ris for it and i cant figure out how to take the thing off

[waffleshotairsoft]

does this gun come with a tightbore??? plz respond

[FinVpo137]

What´s wrong if my gun only works up side down? It simply doesn´t work if it´s not upside down. I don´t mean that the mag would be broken but the gun. It doesn´t fire if it´s not upside down. PLEASE HELP!!!

[akaklol]

@FinVpo137 Lol. That must mean the piston and spring isnt straight. Most likely, did this happen after you took it apart or just happened?

[xE4syComp4nyx]

haha ah shit thats not good

[Animator368]

You are very welcome.

[VanEmergencyNews]

K, I did this broke something :P not important (I hope) w/e. The pin slides in 3/4's of the way. I tried to jam it back and forth yet... still nothing. Also, the upper receiver is kinds lose from the bottom one but I guess that's because it's not entirely together?

Anyways, thanks for the help man.

[EvilLamas]

how do you take appart the upper receiver?!

[maxgator3]

i can not get my hand guard off to put a G&P upper handguard on!!!PLEASE HELP ME.every gun ive ever worked on its come off but this one refuses to come off!!!is there like a trick that i dont know about???

[50cliber]

@maxgator3 if you dont wana use it again saw it offf but if u do then pull on d ring hard and pull hand guard harder lol just man power

[maxgator3]

@50cliber yeah i found out that there are tabs that hold the 2 pieces together so when i pulled the delta ring down it wouldnt come off because the tabs were holding both pieces together

[50cliber]

@maxgator3 ur gun has a case of stuckhandguarditus i have never herd of it sticking it usualy cums of with little force

[maxgator3]

i can not get my hand guard off to put a G&P upper handguard on!!!PLEASE HELP ME.every gun ive ever worked on its come off but this one refuses to come off!!!is there like a trick that i dont know about???

[666SNIP3R666]

so without upgrades rate it from one -10 10 being awesome

[MrCheeseman5000]

no probs, did it work??

[SpinalTapAirSoft]

we have the same gun and when we got it a few days ago we noticed the stock is very loose. Would you happen to know how to tighten the stock?

[MrCheeseman5000]

@SpinalTapAirSoft I have it, if you pull the pin out you can slide the stock completely off, then put masking tape inside, continue putting strips inside untill it is sturdy, works really well!!

[SpinalTapAirSoft]

thanks very much appreciated

[ImSneakyPete]

I got the M4 version and my Charging handle is misaligned (it opens the dust cover). do you know how to get to the charging handle?

[wpracetech]

This gun is supposed to do that,Just like the real thing!

[zSNIP3DOWNz]

@wpracetech the real thing hinges on the front pin.

[shadowbrother18]

is the hop up chamber metal????

[damattalizer]

no, but the hop up is

very effective

[BAYCITYAIRSOFT]

Have you have a problem with your selector plate and switch mine got stripped when I took mine apart.

[Airsofter4444]

can you change the spring in the gearbox without taking the grip off and removing the motor?

[halolovingmaniac]

nope :\

[loudbmw]

Cool vid, thanks man, I wasn't sure if I'd be able to install a TBB and a new bucking myself, but it looks a bit easier than I thought.

[Raneuvfire]

hey wen u took it apart, did the selector switch, like, act wierd as if tightened a little bit? does anyone know bout dat?

[RHLI09]

i just took mine apart and got that, im not sure what caused it :/

[xxxBraveManxxx]

how do you fix the spring holding the the charging handle

[LukasM86]

How do you take the hop-up off?

[dgenerationx767]

i have a little bit of handgrip/barrel wobble how would i fix that?

[mn315on]

All you have to do is take off the delta ring and tighten the nut under that to eliminate barrel wobble. as for the hand grip take out the screws holding in the motor and pull that plate off then dissconect the motor and pull it out then tighten the two screws that hold the grip to the lower reciver.

[MrBlandMan]

I pushed that pin out, and the upper receiver will not move. I can't push it forward at all. Anybody able to help with this?

[DrewMeist]

I had that problem with pulling the G&G GR16 apart for cleaning until I spotted that the wires were too short.

[Epson5000]

I tried dissembling my GR16 Carbine just recently and it wouldn't budge. The pin was moved all the way out but it was stiff and the upper receiver wouldn't slid off.

[odach]

Ive had the same issue.

[Epson5000]

Solution?

[GrazieMille17]

I have the same problem. I'm working on it though and hopefully I can have an answer to the problem soon. What is your G&G, though because maybe there's a difference in the different

GR16s. (Mine's the carbine).

[KuichikiByakuya]

You have to pull the charging handle while sliding it off, at one point the wires will get in the way in the heatsink (the thick part of the wiring with a black rubber casing around it) i cut that out and there were connectors to the wire there, i disconnected those. However the wires were still a problem. i cut the wire again and then soldered it with the other wires.

[Epson5000]

GR16 Carbine

[DeltaFalkon614]

Nice, I've been looking at a G&G for a while and trying to decide if I wanted it or not but this just answered my question. I've been looking for a gun that doesn't require you to be a rocket scientist to open, I have an Echo 1 MP5 Vector Arms and a TM FAMAS and the MP5 is a nightmare to get into. Anyways thanks for uploading this I appreciate it a lot. Actually one more thing, how is the durability on it? Thanks

[skaterpunk310]

that gearbox looks EXACTLY the same as my echo 1 m4 im not joking

[ThugSniperx]

looks the same, yes... acts the same, no lol

[xxGAMRxx]

@skaterpunk310 My echo 1 M4 lasted longer than my G&G M4.

[Tac5Airsoft]

@skaterpunk310 lol they both most likely have a version 2 gearbox

[airsoftmaniac51]

what is a better brand for the m16, JG or G&G?

[pirateninja99]

G&G

[airsoftmaniac51]

cool, thanks!

[airsoftmaniac51]

u have any upgrades on it, and u have any lubricant beside the silicone?

[ThugSniperx]

no upgrades yet and silicone is the only lube i use

[masterofidiots55]

thats what she said!!!

hahahahahaha wow i got you good!

jk nice vid!

[Taurus182]

all airsoft M16 re so easy to open, but why dont ppl rtfm?? but nice video.