When they were paving the Gardener Expressway in Toronto, Canada they did all 3 lanes and the shoulder as the same time; staggered spreaders, so the trucks would have to back down from the next exit ahead. 5th gear in reverse in a 130,000 lb tractor-trailer, that was real trucking right thar.
@whtownejr obviously not Mack Duplex boxes,,, with a seperate stick for Reverse,, high ,, and low ranges. so whatever gear you put it in in the main box,,, is sent through the auxilliary box,, even if the Aux is in reverse
@ScopedOUT2 its only because you "city folk" are morons that apparently cannot read. I do understand that the fundamentals of education are quite as strong in the city schools.
@ScopedOUT2 Wow, what a stupid comment. It's not like you're in the middle of the woods in deep East Texas. It's a construction site. There's a really good chance that most people there live in the city or suburbs.
@129sexyman fuck off you middle class asshole here in england rednecks are called working class and we run rings round you middle class assholes so go fuck you sen are kid . and if you dont know owt about trucks dont say owt get it asshole ?
dumb ass truck drivers thats why i have to put clutches rearends and drive shafts in all the time because their to fuckin stupid to realize their just tearing shit up and doing a piss poor job thats why they drive a dump truck because it really means dumb fuck
ok so here is a bright idea why doesnt the driver use the gravel he is dumping to put on the soft spot, then go in there with a front end loader tractor or backhoe and level/pack the ground with the bucket. then he dosent have to run the piss out of the motor
@mAdAsZaC As I actually do drive dumptrucks. I also know that I do not get myself into situations that get me stuck. Also wherever i dump there has to be a certain load restrictions for the area i drive on meaning packed down and/or graveled properly according to laws. You are right about the less weight and less traction, but in soft dirt no matter how you look at it, you ARE going to get stuck especially backing into it. The driver in the video did well for the conditions
ok the floor it idea was pretty good. but why not use the drop axle? maybe get more surface area touching the ground so it didnt want to sink as bad? that woulda helped tons and been less dangerous.
@EddieErion929 Really because I have run some old macks, 66 Dm800, and the clutch has been somewhat indestructible...not that u really need it much....
@Errorcode38 what are you talking about? this video shows a guy driving fast and you said its a good way to blow the turbo(wrong!)-I say how do you figure and you reply if you shut the engine off the turbo dosnt get oil----- where do you see an engine being shut off here?are you ok?
Yesterday my girlfriend told me she is tired n sleeping,after sometime my friend called me that she is enjoying with a guy.then I went there and cought her red handed with that guy on bed.I was very angry .that bitch told me she dont want me anymore.after what all i have done for her she dumped me for this guy .So in order to take revenge I have posted all her nude pics.
✪check them out on my channel her facebook profile is on my channel
@Brandenlytle1 No, they are just there to keep axel weights down for driving down paved roads. Other than that they just get hung up on things and take traction away from the drives. The problem was that the truck should have stayed out or have bien pulled in by a trackhoe they had one there big enough to pull him in. Thats what chains and tow hooks are for.
@rocintrucker83021227 i am aware of what a lift axle is used for. I am a liscensed Truck and Coach mechanic. it would have helped the issue he was having with the rear sinking.
@Brandenlytle1 I disagree, I respect the fact your a mechanic but dropping the lift axel would not help. As a truck driver with years of off road driving on job sites I know you need the weight on the drives. A lift axel is like the steer axel it will cut in and slow you down and get you hung up. Pit trucks and site trucks that are no longer road able have them removed right away just for that reason. The ground was just to soft and no amount of lift axels would have helped.
@rocintrucker83021227 if it's there to distribute weight it would help it go through soft terrain.. i dont care if you've been drivin trucks for 100 years it's called physics.. thats why nail beds dont kill you
@shooterman619 I'm not talking about physics I'm talking trucks. A lift axel is dead it dose not help with traction. It can't be locked in to help drive. The only way it could be usefull is if it was like a idler wheel on a tracked machine. Then it would help drive as well as distribute the weight. If you watch the vid closely he dose not stop cause he was sinking he was starting to spin. When the back started to hop that means he was spining. Spining can hurt the drive line loaded or empty.
@shooterman619 Physics ? We call them 'Buttons' you push the diff engage BUTTON to turn on your lazy axle and then you FLOOR it. Physics is not needed when you know how to do your job as a second nature and most truckers that have been doing over 5yrs do it as easily as breathing.
@mAdAsZaC you are right about less sinking, but there is also less weight on the drive wheels which will cause them to spin, the more weight, the more traction.
@mcconnell51 i have done many MANY hours with dump truck driver (my dad) now im not going to say i think i would know, but i am 200% sure whenever we got stuck we dumped the load (on the property) and told the excavator driver to load us less heavy.
and the less weight means less need for the inertia (and traction). and the less you sink, there for making it like going down any other level dirt road.
6th gear in reverse ,,,,,,,bullshit there is only a high and low gear unless you stall out the engine kill it and get int running backwards ,,then you can use the forward gears in reverse .but thats not happening here
i was gonna hold my tongue but............................ first off there's a third rear Axle on this truck that is inter-lockable you can see it is free spinning and should of been dropped which distribute the weight to axle ratio thus allowing the truck to gain more traction at a low speed what a lousy way to get to the drop location
That pile of shit does not even look road worthy..Probably way over weight!!Most of the time its retards with 0 education that say gutta do what ya gutta do..Its a dump truck wow the IQ here is amazing!!
Sometimes ya gutta do what ya gutta do ta get the job dun... High side in reverse, best sollution. Cant kill a mack!!!! :-). Takes a good driver to find a solution, without breaking anything.
@KnowledgeIsTheKey09 I'LL let you in on a little common sense going by what i see. First off it goes wrong when the steer tires hit the soft shit and bury themselves and the truck ends up dragging those big steer tires and slowing it down.
Second after he gets through the worse the ground hardens up (SO) whoever was running the job was an idiot, should of had him (DRIVE forward) in and then stop when his steer tires just get out of the soft stuff (Dump) and then turn around on the hard stuff and drive out !!
But i found 99% of shit like this is not the truckers fault, it the idiot running the jobs that don't know what there doing , then they blame the trucker when he gets stuck !! I been doing this 27 years !!
thats 1 reason why i like a 2 stick 6 spd Mack tranny. 5 reverse gears. ;) reverse is in the compound (2nd stick) w/ the lo & hi & ya put compound in reverse & ya got your choice of gears from 1 to 5 in the main (1st stick closet to the driver) Had to do this a few times myself (although i hate to do that due to possibly wring a driveshaft ) made a few hundred on bets saying i couldnt get into soft ground loaded i proved em wrong. but it took a winch cat to pull me out. ;)
No, just like backing up through this shit your DRAGGING them big wide steer tires which slows it down and gets you stuck. If you drive through, those big steer tires will stay on top and you can get through it and dump then get out ...of course if you have room to turn around on hard ground.No longer distance than that, should of dumped and let dozer push it,,saves on wrecking truck, tearing clutch out or dropping drive shaft !!
@theexitproduct Clearly you dont have a clue do you? That middle axle is a tag axle.It is designed to spread the weight out on the road.It would do absolutely nothing for him to put it down backing in there as it is not a driven axle.
@MultiAREE I drove tri-axle dumps for a long time and it does nothing to keep you from bogging out in that type of soft material. That driver is doing exactly what every other dump driver would do except maybe the primadonna Owner operators with the shiny trucks but they dont really like going of road anyway.
6th gear in reverse? Do you mean 10-speed gearbox and reverse gear in high range? In that case reverse gear is as fast 6th gear (lowest gear in high range).
not that impressive. I've backed concrete trucks up to garages and then signaled them to stop and they've only been inches away. Don't it many times. But fast enough.
@alloyzz430 You can't use those axles on the ground when backing up. They are steerable (they turn by themselves), so if you leave them on the ground when backing up, they will turn and dig into the dirt stopping the truck. And anyways, when hauling heavy loads on soft surfaces like mud and dirt, you need all the weight on the drive tires to move, or else you will just spin your tires.
@MrTpengineer Many trucks like this one have multiple ranges and only 4 or 5 actual gears. My dad had a Ford with 5 gears and 4 ranges giving you the ability to have up to 4 reverse gears (not sure if all were usable in reverse). The trucks that I have personally driven generally had 2 ranges but the high range is rarely used when in reverse because of high gearing.
@dirtscratcher Oh yea, we have a black lwnmower (off subject) with 2 seperate shifters, one is for nutral, reverse, and forward, while the other is for gears 1-7. But they all work in reverse also. Got it :)
It has an other axle unused to use it would help for the weight distribution
michaelovitch 13 hours ago
They never heard of iron plates?
kitchenfromhell 5 days ago
What's an ass truck?
ihmesekoilua 1 week ago
Why didn't the idiot have his diff locks on then it wouldn'tve span and churned the ground anywhere near as much
Ultimatepanzer 1 week ago
This has been flagged as spam show
Reminds me of my brother.
thespwillliveforever 1 week ago
He made it like the same distance everytime, what difference is 10 ft when you're moving it with heavy equipment anyway?
loostonerool 1 week ago
Lol when you see shit like this your in Texas
kylethefeirce1 1 week ago
haha 6th gear in reverse thats funny
bozo148 1 week ago
When they were paving the Gardener Expressway in Toronto, Canada they did all 3 lanes and the shoulder as the same time; staggered spreaders, so the trucks would have to back down from the next exit ahead. 5th gear in reverse in a 130,000 lb tractor-trailer, that was real trucking right thar.
mannwhosoldtheworld 1 week ago
Hell Yeah.
TheWicho46 1 week ago
I'm a city folk,
and I think this is hilarious
Spacek531 2 weeks ago 3
'
this truck can go backward with a shift - N - netural
bestamerica 2 weeks ago
thats how u get shit done
my1990silverado 2 weeks ago
learn how to built a road with rock not dirt and it wouldnt be soft and that truck is a piece of shit
jdcatskinner 2 weeks ago
Yawwwwwn been there done that
herb725 2 weeks ago
why not just put some wood down and rive on that?
TheUsmc29 3 weeks ago
@TheUsmc29 do you even know how hard it is to rive on wood? Riving is one of the most complicated tasks when it comes to Ruck's and Emi's
lacoste10156 2 weeks ago
@lacoste10156 No i dont, i was just throwing it out there...im sorry :'(
TheUsmc29 2 weeks ago
Huh....all my trucks have 1 reverse with a "High" side and a "low" side giving me "2" reverse gears......am I not looking far enough under the mat?
whtownejr 3 weeks ago
@whtownejr No, you are not old enough to know different
It's a MACK and has to be older than 1987
The transmission will be a TRXL1071. Should be a few videos of people driving one
viper1966 2 weeks ago
@whtownejr obviously not Mack Duplex boxes,,, with a seperate stick for Reverse,, high ,, and low ranges. so whatever gear you put it in in the main box,,, is sent through the auxilliary box,, even if the Aux is in reverse
BIGTARBABY71 2 weeks ago
gotta love them old macks!
whitehd01 4 weeks ago
This truck could only have 4 reverse gears. Correct me if I am wrong. You had said 6th gear reverse.
bulldog0046 4 weeks ago
Redneck truck drivin at its best!!!
RanchhandTCR 4 weeks ago
now its even, but i did like it
scnatureboy69 1 month ago
im a city guy and i got that lol... then again i want to be a redneck hahaha
TheBlainedurousseau 1 month ago
gotta be ya best viewed vid so far!..... good job mate
cheeptorque 1 month ago
Doubt if this was OSHA approved. LOL!!
bitethedevil 1 month ago
The ol twin stick mack was good for something... more reverse gears haha
maniacfred 1 month ago
Definitely did not hit 30.
trogdorpontiac 1 month ago
Here's a revolutionary idea! COMPACT THE SOIL OVER THE BRIDGE FIRST!!!
UsedMissiles 1 month ago
dam good drivin for sure
randytosh 1 month ago
keeping it even, and not just for the sake of it, i get it
Mr305wrangler 1 month ago
Not much room I was surprised he was able to get into 6th
travisjeanelle 1 month ago
614 LIKES AND 614 DISLIKES OMG
MrSqwiggles1 1 month ago
Over 600 Rednecks knew what his video was about
An Equal number of city folks are still scratching their heads.
ScopedOUT2 1 month ago 32
@ScopedOUT2 its only because you "city folk" are morons that apparently cannot read. I do understand that the fundamentals of education are quite as strong in the city schools.
boyisgood2085 1 month ago
@ScopedOUT2 Wow, what a stupid comment. It's not like you're in the middle of the woods in deep East Texas. It's a construction site. There's a really good chance that most people there live in the city or suburbs.
chechnya 4 weeks ago
@ScopedOUT2 ur saying you rednecks are better than us? im a city guy and i knew exact;y what this video was about dumbass.
129sexyman 1 week ago
@129sexyman fuck off you middle class asshole here in england rednecks are called working class and we run rings round you middle class assholes so go fuck you sen are kid . and if you dont know owt about trucks dont say owt get it asshole ?
yorkshiretractors 2 days ago
@129sexyman yorkshire rules city boy do you get it asshole ?
yorkshiretractors 2 days ago
Americans...
BadSkilljoy 1 month ago
why didn't you just lower your other wheels and disperse your weight
uancb1994 1 month ago
this vid should be renamed.......... STEERING WHEEL ATTENDANT WITH NO RESPECT FOR HIS TRUCK
caboolturescumbag 1 month ago
Doesen't matter rage quit!
GokuDussek1232 1 month ago
How stupid can the person who is doing the editing be.... It is not possible for the truck to be in 6th gear in reverse.
DeisleDawg88 1 month ago
@DeisleDawg88 with a mack transmission you can.
rigjockey423 1 month ago
MACK truck 'nuff said.
punhoss 1 month ago
That truck needs Tireboss.
allblacks420 1 month ago
dumb ass truck drivers thats why i have to put clutches rearends and drive shafts in all the time because their to fuckin stupid to realize their just tearing shit up and doing a piss poor job thats why they drive a dump truck because it really means dumb fuck
jessehaug1 1 month ago
personally i would have lowered the third set of tires down and distrubted the wait better more wheels less sinking just my opinion
kutter987 1 month ago
@kutter987 the way he was sinking in the other set of wheel was not gonna make a differance.
Shabbernigdo 1 month ago
crazy?.... do that shit every day here in new zealand...
CRMANL 1 month ago
Wow. Way to film the same thing from different angles. Oh. AND you know how to speed up a video. Congratulations!
Lordmeats 1 month ago
???
bagsikboss 2 months ago
ok so here is a bright idea why doesnt the driver use the gravel he is dumping to put on the soft spot, then go in there with a front end loader tractor or backhoe and level/pack the ground with the bucket. then he dosent have to run the piss out of the motor
nocerloker 2 months ago
@mAdAsZaC As I actually do drive dumptrucks. I also know that I do not get myself into situations that get me stuck. Also wherever i dump there has to be a certain load restrictions for the area i drive on meaning packed down and/or graveled properly according to laws. You are right about the less weight and less traction, but in soft dirt no matter how you look at it, you ARE going to get stuck especially backing into it. The driver in the video did well for the conditions
mcconnell51 2 months ago
Must be Hugh Rowland driving! hahahaha
catfishakaAMC 2 months ago
Ummm, why not just use the skid steer to move the whole 10yrds of loam? I meen the truck got 20 extra feet by running at it over and over.
51supernova50 2 months ago
ok the floor it idea was pretty good. but why not use the drop axle? maybe get more surface area touching the ground so it didnt want to sink as bad? that woulda helped tons and been less dangerous.
jlcyamaha 2 months ago
dont see anything crazy about this at all. the load got where it was supposed to be didnt it?
truckerjay1 2 months ago
listen to that turbo! 0:41
IOwn4Tractors 2 months ago
The guy said its good enough, but nope had to go for the 3rd try...Those old mack sticks shifts are fun....
tjsage79 3 months ago
@tjsage79 no their not-they are the worst trans in the buisness
EddieErion929 3 months ago
@EddieErion929 Really because I have run some old macks, 66 Dm800, and the clutch has been somewhat indestructible...not that u really need it much....
tjsage79 3 months ago
@tjsage79 who said anything about the clutch?
EddieErion929 2 months ago
Good way to blow up your turbo...
Errorcode38 3 months ago
@Errorcode38 how do you figure?
EddieErion929 3 months ago
@EddieErion929 Because if the turbo is spinning and you turn the engine off, the turbo ain't get oil anymore.
Errorcode38 2 months ago
@Errorcode38 what are you talking about? this video shows a guy driving fast and you said its a good way to blow the turbo(wrong!)-I say how do you figure and you reply if you shut the engine off the turbo dosnt get oil----- where do you see an engine being shut off here?are you ok?
EddieErion929 2 months ago
Maybe doing a better job of packing the dirt as it was built up would be the smart thing to do. They do make machines for that.
ffjsb 3 months ago
This has been flagged as spam show
✪✪✪✪✪✪PLEASE READ AND HELP✪✪✪✪✪
Yesterday my girlfriend told me she is tired n sleeping,after sometime my friend called me that she is enjoying with a guy.then I went there and cought her red handed with that guy on bed.I was very angry .that bitch told me she dont want me anymore.after what all i have done for her she dumped me for this guy .So in order to take revenge I have posted all her nude pics.
✪check them out on my channel her facebook profile is on my channel
✪✪✪✪✪THANK YOU ✪✪✪✪✪
revenge1820 4 months ago
shoulda dropped the lift axle.
Brandenlytle1 4 months ago
@Brandenlytle1 No, they are just there to keep axel weights down for driving down paved roads. Other than that they just get hung up on things and take traction away from the drives. The problem was that the truck should have stayed out or have bien pulled in by a trackhoe they had one there big enough to pull him in. Thats what chains and tow hooks are for.
rocintrucker83021227 4 months ago
@rocintrucker83021227 i am aware of what a lift axle is used for. I am a liscensed Truck and Coach mechanic. it would have helped the issue he was having with the rear sinking.
Brandenlytle1 4 months ago
@Brandenlytle1 I disagree, I respect the fact your a mechanic but dropping the lift axel would not help. As a truck driver with years of off road driving on job sites I know you need the weight on the drives. A lift axel is like the steer axel it will cut in and slow you down and get you hung up. Pit trucks and site trucks that are no longer road able have them removed right away just for that reason. The ground was just to soft and no amount of lift axels would have helped.
rocintrucker83021227 4 months ago
@rocintrucker83021227 if it's there to distribute weight it would help it go through soft terrain.. i dont care if you've been drivin trucks for 100 years it's called physics.. thats why nail beds dont kill you
shooterman619 4 months ago
@shooterman619 I'm not talking about physics I'm talking trucks. A lift axel is dead it dose not help with traction. It can't be locked in to help drive. The only way it could be usefull is if it was like a idler wheel on a tracked machine. Then it would help drive as well as distribute the weight. If you watch the vid closely he dose not stop cause he was sinking he was starting to spin. When the back started to hop that means he was spining. Spining can hurt the drive line loaded or empty.
rocintrucker83021227 4 months ago
@rocintrucker83021227 bla bla bla physics is physics.. and it applies to everything from trucking to fucking
shooterman619 3 months ago
@shooterman619 Physics ? We call them 'Buttons' you push the diff engage BUTTON to turn on your lazy axle and then you FLOOR it. Physics is not needed when you know how to do your job as a second nature and most truckers that have been doing over 5yrs do it as easily as breathing.
mark23q123 2 months ago
@mark23q123 if you distribute your weight with more axles it puts less load on the wheels making it easier to move
shooterman619 2 months ago
@shooterman619 Hes in a tipper mate that load cant be spread out anymore then it already is. All he has to work with here is skill.
mark23q123 2 months ago
@mark23q123 spread in a larger area.. on the GROUND
shooterman619 2 months ago
@shooterman619 less load on the wheels means less traction for the drive wheels tho. Just a point
mcconnell51 2 months ago
@mcconnell51 but less load on the wheels means less sinking and less need for traction
mAdAsZaC 2 months ago
@mAdAsZaC and @mcconnell51 finally someone rational.. thank you!
shooterman619 2 months ago
@mAdAsZaC you are right about less sinking, but there is also less weight on the drive wheels which will cause them to spin, the more weight, the more traction.
mcconnell51 2 months ago
@mcconnell51 i have done many MANY hours with dump truck driver (my dad) now im not going to say i think i would know, but i am 200% sure whenever we got stuck we dumped the load (on the property) and told the excavator driver to load us less heavy.
and the less weight means less need for the inertia (and traction). and the less you sink, there for making it like going down any other level dirt road.
mAdAsZaC 2 months ago
6th gear in reverse ,,,,,,,bullshit there is only a high and low gear unless you stall out the engine kill it and get int running backwards ,,then you can use the forward gears in reverse .but thats not happening here
notavailable101 4 months ago
i was gonna hold my tongue but............................ first off there's a third rear Axle on this truck that is inter-lockable you can see it is free spinning and should of been dropped which distribute the weight to axle ratio thus allowing the truck to gain more traction at a low speed what a lousy way to get to the drop location
pastorgeorgem 4 months ago
That pile of shit does not even look road worthy..Probably way over weight!!Most of the time its retards with 0 education that say gutta do what ya gutta do..Its a dump truck wow the IQ here is amazing!!
sinisterskid 4 months ago
so whats crazy ?
club4ghz 4 months ago
Sometimes ya gutta do what ya gutta do ta get the job dun... High side in reverse, best sollution. Cant kill a mack!!!! :-). Takes a good driver to find a solution, without breaking anything.
chevy1995red 4 months ago
Crazy would be doing donuts in that thing (with the full load, hell even with an empty load).
dstaplet01 4 months ago
I'd say the odds are against him! For everytime he doesnt get stuck his pay should double LOL!!!!
simonspics1 4 months ago
Did i mis something here? Cause i didn't see it, or got it?!?!
periesicsd 4 months ago 10
There's nothing crazy about that
JRod350 5 months ago
that right there's how ya gotta do it.
redreaper2020 5 months ago
Amazing thinking billy!
Not a single fuck was given..
LetsKillElmo 5 months ago
If that was my old bulldog that driver would be looking for a job.
CumminsISX 5 months ago
Any of you super trucker see where it all went wrong ?? If you don't you need to change occupations !!
KnowledgeIsTheKey09 5 months ago
@KnowledgeIsTheKey09 I'LL let you in on a little common sense going by what i see. First off it goes wrong when the steer tires hit the soft shit and bury themselves and the truck ends up dragging those big steer tires and slowing it down.
KnowledgeIsTheKey09 5 months ago
Second after he gets through the worse the ground hardens up (SO) whoever was running the job was an idiot, should of had him (DRIVE forward) in and then stop when his steer tires just get out of the soft stuff (Dump) and then turn around on the hard stuff and drive out !!
KnowledgeIsTheKey09 5 months ago
But i found 99% of shit like this is not the truckers fault, it the idiot running the jobs that don't know what there doing , then they blame the trucker when he gets stuck !! I been doing this 27 years !!
KnowledgeIsTheKey09 5 months ago
y they just did not put heavy duty boards down
adrianparker98 5 months ago
I hope you die doing other stupid shit....really.
FLAG FOR DANGEROUS ACTS OF STUFUCKINGPIDITY
analyzingfunny 5 months ago
thats 1 reason why i like a 2 stick 6 spd Mack tranny. 5 reverse gears. ;) reverse is in the compound (2nd stick) w/ the lo & hi & ya put compound in reverse & ya got your choice of gears from 1 to 5 in the main (1st stick closet to the driver) Had to do this a few times myself (although i hate to do that due to possibly wring a driveshaft ) made a few hundred on bets saying i couldnt get into soft ground loaded i proved em wrong. but it took a winch cat to pull me out. ;)
B422TMack 5 months ago
Giá HOWO
liên hệ : Đỗ Phong : 0976.208.950
Trân trọng cám ơn
0976208950 6 months ago
ive never driven a dump truck but whatta fuck does 6th gear in reverse means? how do u engage reverse and 6th gear at the same time
abelucious 6 months ago
@abelucious 2nd gear box? seen a few like that
scott192 6 months ago
In later model Macks you can shift going backwards just like you can going forwards, started in the 90's i think
KnowledgeIsTheKey09 5 months ago
just a rookie comment but wouldnt that other axle on the ground help with spreading out some of the weight??
hockyongrass1 6 months ago
@hockyongrass1 yea but it would lift the weight off the drive giving you less traction ;)
steven1991c 6 months ago
No, just like backing up through this shit your DRAGGING them big wide steer tires which slows it down and gets you stuck. If you drive through, those big steer tires will stay on top and you can get through it and dump then get out ...of course if you have room to turn around on hard ground.No longer distance than that, should of dumped and let dozer push it,,saves on wrecking truck, tearing clutch out or dropping drive shaft !!
KnowledgeIsTheKey09 5 months ago
oh my goooooodness. . . . . .
listen to the wonderful sound of the turbo spooling. Now that is music to my ears.
divery4eyes 6 months ago
Must be a Mexican
VERYevilVIDEOop 6 months ago
@VERYevilVIDEOop yea cuz you dumb ass white boys cant drive for shit lol.
wilfredc190 6 months ago
hes a crazy motherfucker
TheMrRedbullrocks 6 months ago
must be a bunch of mexicans.
ryanmxn 6 months ago
wot a complete knob head typical dumb yank
griffbuild 7 months ago
if you put down your middle wheels you won't get stuck as much :)
theexitproduct 7 months ago
@theexitproduct Clearly you dont have a clue do you? That middle axle is a tag axle.It is designed to spread the weight out on the road.It would do absolutely nothing for him to put it down backing in there as it is not a driven axle.
shadowr434 7 months ago
@shadowr434 Spreading the weight would mean you won't get stuck as much?
MultiAREE 7 months ago
@MultiAREE I drove tri-axle dumps for a long time and it does nothing to keep you from bogging out in that type of soft material. That driver is doing exactly what every other dump driver would do except maybe the primadonna Owner operators with the shiny trucks but they dont really like going of road anyway.
shadowr434 7 months ago 2
zzz you have some stones at the side you can put it on the road to make it more harder
JamesLim951 7 months ago
GIVE ER SHITT!!
Redneckmuddinboyz 7 months ago
On the contrary "Class Truck Driver"
Dogslow 7 months ago
turbo gwizda ale szofer pizda
krzysiuas 7 months ago
this is how things how wrong
FoGGeRdk 7 months ago
who's crazy?
SuperAvailable123 7 months ago
6th gear in reverse? Do you mean 10-speed gearbox and reverse gear in high range? In that case reverse gear is as fast 6th gear (lowest gear in high range).
A77uros 7 months ago
WOW, SO AMAZING.......not
stuart200sx1980 7 months ago
@stuart200sx1980 shut the fuck up
03056932 7 months ago
@03056932 Faggot
stuart200sx1980 7 months ago
@stuart200sx1980 You MUST be gay
03056932 7 months ago
haul ass in reverse sounds like a good name for an 80s hairband
tsharpmac420 7 months ago 57
@tsharpmac420 Or a porno
johndeere445 6 months ago 29
@johndeere445 tru lol
tsharpmac420 6 months ago
Sounds like me and my old man, Haul ass in reverse
the1996bronco 7 months ago
if there would be an european truck he will had no problems
skipperliviu 7 months ago
i only watched this video to listen to that buetiful mack engine
CFDPaul 8 months ago
How do I get here...
AbbieForPresident 8 months ago
a polak by se ku**wa gruzu podsypal :P
kamilsnk88 8 months ago
@kamilsnk88 Easy for you to say... I guess.
oldfart387 7 months ago
движок нетянет, вот и все проблемы
Timofey83 8 months ago
not that impressive. I've backed concrete trucks up to garages and then signaled them to stop and they've only been inches away. Don't it many times. But fast enough.
SDSpike 8 months ago
Louisiana @ it's finest?
bmxdude1515151515 8 months ago
This has been flagged as spam show
everyone please watch my videos and especially rapping indian
TheDuke543210 8 months ago
1:10 slychać strzały...
Valpurgius1986 8 months ago
6th gear in reverse??? unless its a double shifter...not possible
bobbysc7 8 months ago 2
Gotta be the south somewhere
chaz7r 8 months ago
Stupid =_=
ThePaperblur 8 months ago
thats not crazy...
zachchaffee 8 months ago 2
cool,exactly 1000 vids :P
jibu8 8 months ago
And this is what rednecks do for fun.
Welcome to Alabama...
lexilovesTRS 9 months ago 2
Why not just use the "bucket" on the power shovel over there to push it back the rest of the way? It's got the strength, it'll do it.
mav1269 9 months ago
So why didn't he use the 4th axle to help bear the weight?
alloyzz430 9 months ago
@alloyzz430 You can't use those axles on the ground when backing up. They are steerable (they turn by themselves), so if you leave them on the ground when backing up, they will turn and dig into the dirt stopping the truck. And anyways, when hauling heavy loads on soft surfaces like mud and dirt, you need all the weight on the drive tires to move, or else you will just spin your tires.
yakilaky 9 months ago 2
he's an ass truck driver then?
AK47JUNKIEfromNT 9 months ago
Dumb asses!!! 6th gear in reverse?????
teawithsu 9 months ago
hehe i love ass trucks
spyder317 9 months ago
trucks can shift in reverse??? weird.
MrTpengineer 9 months ago
@MrTpengineer Many trucks like this one have multiple ranges and only 4 or 5 actual gears. My dad had a Ford with 5 gears and 4 ranges giving you the ability to have up to 4 reverse gears (not sure if all were usable in reverse). The trucks that I have personally driven generally had 2 ranges but the high range is rarely used when in reverse because of high gearing.
dirtscratcher 9 months ago
@dirtscratcher Oh yea, we have a black lwnmower (off subject) with 2 seperate shifters, one is for nutral, reverse, and forward, while the other is for gears 1-7. But they all work in reverse also. Got it :)
MrTpengineer 9 months ago
please crash..
please crash..
please crash.. Fuck'n fuck you douche!
Paperism1ne 9 months ago
I'm no trucker but isn't this one of those situations where you drop the drop axle?
scarble 9 months ago
How do you have a sixth gear in reverse?
calboy5858 9 months ago
@calboy5858 Some older trucks had as many gears in reverse as they did in forward.
500SWMAGOPERATOR 9 months ago
???so what. that was stupid. thumbs down.
externalpower 9 months ago
Alcohol has to be involved in this somehow
shawnkrause871 9 months ago
@shawnkrause871 U never worked a hard day in ur life you fucking spoiled faggot bitch.
coolhandcanada 9 months ago
@coolhandcanada Wow...that's a reasonable reaction to a harmless comment...Looks like someone needs anger management.
shawnkrause871 9 months ago
@shawnkrause871 WHAT!!! I'll fucking beat you in everything ever created on the planet you fucking spoiled faggot.
coolhandcanada 9 months ago