ya i ended up goin boost on my a3..... went with revhard kit, 750cc RC's, 255 walbro, stagw 3 act. Clutch Pack, k-pro and dyno tuned on mustang dyno and ended up making like 297whp260wtqr on 11-12psi and 360whp300+wtq on 15psi with 110oct/92 oct pump mix =)....... its a vette KILLLER
ok so your fully built engine ie rods pistons crank bored out, makes more power then a basicly stock accord engine.....i give up you win do you want a medal or a chest to pin it on?
400 bux for the engine, and i get 35+ mpg and a 14.0 in the quarter. k20s are fun and all but ill always make more torque, unless your boosted but then you wouldnt be comparing apples to apples....to each thier own
@fordkiller12 shit man i have an ep3 and mad props on your part fuck the haters, they just wish they had a car as nice as an ep3 :D and you know dude is lying about having a toda stroked 2.2 lol he also has a enzo for his DD rofl
all you need is the crv side mount about 32 bux from honda. swap over all the sensors that dont fit to the plugs on the harness. and thats about it. very simple i can pull a car in the garage and less then 10 hours later i can drive it out with a new engine
k24a1 and boost are a good combo, reliable dd id say 300, or if you want the stocvk bottoms are good for 400 easy, as much as 500 in some cases, k24a4, a1 and a2 bottom ends are different, a4's are a little weak for boost
ya i ended up goin boost on my a3..... went with revhard kit, 750cc RC's, 255 walbro, stagw 3 act. Clutch Pack, k-pro and dyno tuned on mustang dyno and ended up making like 297whp260wtqr on 11-12psi and 360whp300+wtq on 15psi with 110oct/92 oct pump mix =)....... its a vette KILLLER
rcysi 9 months ago
what type of header are you using to fit the k24?
FishBoneSkeleton 10 months ago
@FishBoneSkeleton
K series megan and tesp pie work great, ive since switched to an OBX one piece 4:2:1 header, it fits well too
ficodecko 9 months ago
weak as fuck iv a k20 2.2 toda stroka kit thats fucking better than that
TheWeaponThayFear666 11 months ago
@TheWeaponThayFear666
oh ok that makes alot of sence your fully built engine is better then my stock accord engine......
ficodecko 9 months ago
@ficodecko yes y spend all that money on a engine swap when it is still slow u ronker
TheWeaponThayFear666 9 months ago
@TheWeaponThayFear666
ok so your fully built engine ie rods pistons crank bored out, makes more power then a basicly stock accord engine.....i give up you win do you want a medal or a chest to pin it on?
ficodecko 9 months ago
what tranny did you use?
20Luder00 1 year ago
@20Luder00
ive had em all but the itr/ctr that was a k20a3 trans out of the ep3, then i went to a 6 speed from an rsx then a 5speed from a base
ficodecko 9 months ago
this is exactly why i beat ep3's.
slightlyslammed 1 year ago
haha dont listen to these guys, they can have there A3 haha. ill take them fat pistons and stroke any day of the weak. Keep up the work.
oskar87A1 1 year ago
really thats a waste of money... my a3 was as fast....FAIL
RevHardEp3 1 year ago
@RevHardEp3
400 bux for the engine, and i get 35+ mpg and a 14.0 in the quarter. k20s are fun and all but ill always make more torque, unless your boosted but then you wouldnt be comparing apples to apples....to each thier own
ficodecko 9 months ago
mods list?
Akeeg4 2 years ago
oh really that sounds pretty good.
Would i be able to use the same wiring harness from my stock k20a3?
Cuss i found a K24a4 with 40k miles for 850 bucks and thek24a4 ECU for a $100 online.
So all i would need now is the side mount from a crv and someone to put it into my car?
by the way what clutch would i be needing to raplce it? what model car?
fordkiller12 2 years ago
@fordkiller12
yes the harness works you just need to steal a sensor or two off the old k20 engine
ficodecko 9 months ago
@fordkiller12 shit man i have an ep3 and mad props on your part fuck the haters, they just wish they had a car as nice as an ep3 :D and you know dude is lying about having a toda stroked 2.2 lol he also has a enzo for his DD rofl
BoogieMain17 8 months ago
NICE VID BRO.
I HAVE AN 04SI STOCK BASIC BOLT ON'S.
I WANT TO SLAP IN A K24A4 Found in:2003-2005 Honda Accord, 2003-2006 Honda Element.
IS THERE ANY MODS I HAVE TO DO TO THE FRAME OR DOES THE THE K24A4 SWAP RIGHT IN? IF YOU COULD GIVE ME A QUICK RUN DOWN THAT'D BE GREAT.
THANKS.
fordkiller12 2 years ago
all you need is the crv side mount about 32 bux from honda. swap over all the sensors that dont fit to the plugs on the harness. and thats about it. very simple i can pull a car in the garage and less then 10 hours later i can drive it out with a new engine
ficodecko 2 years ago
@ficodecko wich aecu are you using ?
200horsepower 1 year ago
@200horsepower
Kpro on an RSX ecu
ficodecko 9 months ago
not tryna be negative.. but i think my a3 pulls aboout the samee.. get that built motor in lol
endlessfable 2 years ago
i ran a 14.8 untuned without the 6 speed and no front 02 sensor, with all of that fixed i was about a 14.2
ficodecko 2 years ago
04 si? i was lookin to throwin the k24 in my car and boostin it..just got out the navy so i got some extra money to blow 8)
Magician1607 3 years ago
k24a1 and boost are a good combo, reliable dd id say 300, or if you want the stocvk bottoms are good for 400 easy, as much as 500 in some cases, k24a4, a1 and a2 bottom ends are different, a4's are a little weak for boost
ficodecko 3 years ago
i have a ep3 and was wonderin if the k24 was a easy swap on on the ep3....or is there any custom modification
closest2nike 3 years ago
its very easy all you need is the passanger side crv motor mount
ficodecko 3 years ago
rev that bitch higher then that :)
GUARDIAN702 3 years ago
7600 is alot for a k24a4 especialy those weak ass accord rods lol, i just cant wait till my tsx block is built!
ficodecko 3 years ago
yeah its a stock engine just some bolt ons and kpro i have a 6 speed in it now and a tsx block in my room for later down the road
ficodecko 3 years ago
So that's a stock Accord engine, not a K24/ K20 right? Otherwise I was gonna say!
Get an A2 Head and either CRV pistons or TSX pistons!
chitalia17 3 years ago