The setup made a huge enhancement in the last weeks, sadly i didn´t had the time to make the next video but i will when i get time.
The engine wasn´t dynoed with carb, because that little bloody thing was absolutely worn out, the engine ran like crap. The throttle body exactly fits the stock part which takes the carb, so no big problems with that. I haven´t calculated the price, but i guess its about a few hundred euros till now. Take the CR500, that would be definately awesome! :-)
I´ve heard that too. But luckily my wideband 02 sensors doesn´t know, that he should have been defective since many miles :-) to be honest, i think i will be destroid, but no one knows exactly when this will happen. i guess it really depends how much oil is in the exhaust gas and in my case its really less, ~1:80.
u need more displacement u say mmm for the rs 125 u can get a polini 154 kit or pjmes 144 kit both suppsed to be good but polini needs porting for the bike to rev past 10k i think good luck.
i have a polini which is in very good condition, but sadly its c.r. is so high it reaches easily 15bar and the starter isn´t capable of starting the engine. the way to go is a RSi 250 or even better a honda CRi 250 :-)
hey hey, its finally got its legs. Hows it running now? It sounds like the fuel mixture is just about right. How much horse power is this thing now producing???
actually its running a bit to rich, again. i mounted a performance head from xx-racing at that richened the mixture quite a lot. i will lean it out in spring 09 and i guess i will sell it in summer 09, i definately need more engine displacement!
@netmaster78 that 130 number its the temperature ??? if it is your piston rings are burneeed
mrx495 6 days ago
I,m very impressed what what you have acheived so far i
I,m going to try and use a MS on my Cr500 Sm
i have been reading up loads about it and you have pulled it off well .
have you dynoed the bike before you converted it to injection ?
how did you get the gsxr manifold to mate to the intake reed cage ?
how much has it cost so far ?
Did i say i have an Rs125 maybe i should try it on that first as a learning curve keep up the great work look forward to your next vid.
AcidVFR400R 3 years ago
The setup made a huge enhancement in the last weeks, sadly i didn´t had the time to make the next video but i will when i get time.
The engine wasn´t dynoed with carb, because that little bloody thing was absolutely worn out, the engine ran like crap. The throttle body exactly fits the stock part which takes the carb, so no big problems with that. I haven´t calculated the price, but i guess its about a few hundred euros till now. Take the CR500, that would be definately awesome! :-)
netmaster78 3 years ago
Great job!
How do you measure the air/fuel ratio? I thought that lambda sensors could not work with 2 stroke engines.The burned oil destroys the o2 sensor.
biofotis 3 years ago
I´ve heard that too. But luckily my wideband 02 sensors doesn´t know, that he should have been defective since many miles :-) to be honest, i think i will be destroid, but no one knows exactly when this will happen. i guess it really depends how much oil is in the exhaust gas and in my case its really less, ~1:80.
netmaster78 3 years ago
u need more displacement u say mmm for the rs 125 u can get a polini 154 kit or pjmes 144 kit both suppsed to be good but polini needs porting for the bike to rev past 10k i think good luck.
satanem 3 years ago
i have a polini which is in very good condition, but sadly its c.r. is so high it reaches easily 15bar and the starter isn´t capable of starting the engine. the way to go is a RSi 250 or even better a honda CRi 250 :-)
netmaster78 3 years ago
what is that?
BigTeo89 3 years ago
what do you mean exactly?
the bike? its a 1997 aprilia rs125.
the notebook? its a dell d410.
the software? its the control-software for the ecu.
maybe i could give you a more precise answer by knowing what exactly you mean ;-)
netmaster78 3 years ago
cazzo è?
BigTeo89 3 years ago
sorry, in english please ;-)
netmaster78 3 years ago
hi mate , were did u get that software from for ur rs125? cheers dan
dansapriliars125 3 years ago
its delivered with the ecu.
netmaster78 3 years ago
hey hey, its finally got its legs. Hows it running now? It sounds like the fuel mixture is just about right. How much horse power is this thing now producing???
Foz1990 3 years ago
well, its on the right way. sadly i burned the head gasket last weekend, so i have to fix that first. time to raise the timings :-D
i hope its running next weekend with a bit more power, the actual hp is untested till october or november.
netmaster78 3 years ago
great work on this how is it running and performing now? I am very very intrested in this
smorg12 3 years ago
actually its running a bit to rich, again. i mounted a performance head from xx-racing at that richened the mixture quite a lot. i will lean it out in spring 09 and i guess i will sell it in summer 09, i definately need more engine displacement!
netmaster78 3 years ago