WHO KNOWS:How to make a simple generator fog/smoke?1.A bucket or pot- The combustion chamber. 2.A small fan-pumping air.3. Metal tube with water in a bucket. And what to do to smoke was flying to the ground?I would like to make this generator create smoke as smoke grenade. Maybe someone knows any links to pages? Thanks in advance.
3 psi is fine. You will need a very large cylinder and run as a vacuum engine. The earliest steam engines used this method. Just a little steam at very low pressure was admitted and as it collapsed in the cooler cylinder the normal 14.7 psi air pressure acted on the cylinder. 14.7 psi x 78.5 sqin = 1154 Lbs on the shaft. Its a slow but powerful engine. Gear it to a faster turning output.
would you sell me a circuit plan, and what the parts are? i am building a steam launch and with 12 volt system solar power and also a generator, using a permant magnet motor as a generator. thanks
Yes, I am satisfied, it works very well. Sorry to not follow up. Personal message me and I will get you the diagram or I can sell you a circuit already made. 12 vdc, probe wire sensing water level, and two control wires for pump or solenoid.
I want to make a small thermal power plant for a school project (and also for fun), I saw many images of small monotube boiler, but which are high pressure, I need 50 psi to 80 psi to get 500 to 800W using a turbine tesla with 10 disks of up to 14 cm. I need a pump to inject water in the boiler monotube? If yes, how much power the pump?
That is a very nice unit! Well done! I am in the process of building a down draft gasifying hot air furnace as well. I Have to wonder how much energy has been wasted over the years when I see a smokey chimney from other houses. I would like to learn more about your smoke eating machine.
Did I miss something in you other vids I thought u using a coil of copper as a boiler how does the spark plug tie into that. also could you give us parts list and schematic of your control system in the next eppisode
Yes, there is a coil of copper tubing about 175 feet long. The spark plug is used as a means to complete a low voltage circuit when water is present in the tubing circuit just before it enters the evaporator section.
Yes, I will share the circuits, and schematics when I am satisfied. I have attempted to keep things as off the shelf and simple as possible.
What are these used for?
kayakcurtis 1 month ago
Great! A BBQ for the sauna :-)
HLANGEL100 1 month ago
WHO KNOWS:How to make a simple generator fog/smoke?1.A bucket or pot- The combustion chamber. 2.A small fan-pumping air.3. Metal tube with water in a bucket. And what to do to smoke was flying to the ground?I would like to make this generator create smoke as smoke grenade. Maybe someone knows any links to pages? Thanks in advance.
Sebol811 3 months ago
Nice boiler! Don
donmaguire 7 months ago
Hi: Great work...Roughly how much PPM of steam does this generate?
rightuse 8 months ago
3 psi is fine. You will need a very large cylinder and run as a vacuum engine. The earliest steam engines used this method. Just a little steam at very low pressure was admitted and as it collapsed in the cooler cylinder the normal 14.7 psi air pressure acted on the cylinder. 14.7 psi x 78.5 sqin = 1154 Lbs on the shaft. Its a slow but powerful engine. Gear it to a faster turning output.
HER0911 9 months ago
nice work im trying to build something like that but i only need 3 psi and run it on propane and it needs to run for 24 hours constant any advice?
kpshc707 9 months ago
what is the point of it?
SensaeBushcraft 1 year ago
I would also like to purchase a circuit plan if you have it.
gbclayjr 1 year ago
Impressive system!
sjh7132 1 year ago
would you sell me a circuit plan, and what the parts are? i am building a steam launch and with 12 volt system solar power and also a generator, using a permant magnet motor as a generator. thanks
rchoppertrike10 1 year ago
If you would like any steel tube boilers, or a good boiler source?
Find an old hotsy steam preshure washer they are safty rated up
too a preshure of 600 psi. Burn used motor oil with only a very slight
Adjustment.
FireDropTechnologies 1 year ago
Yes, I will share the circuits, and schematics when I am satisfied.
Hi, nice work. I have to say it, are you satisfied yet? I'm looking at a coffee machine pump for the feed water, just need to control it.
Love your videos.
nrg4all 1 year ago
@nrg4all
Yes, I am satisfied, it works very well. Sorry to not follow up. Personal message me and I will get you the diagram or I can sell you a circuit already made. 12 vdc, probe wire sensing water level, and two control wires for pump or solenoid.
LynxSteam 1 year ago
I was curious where you got the pump and electronics for this project?
mycoptah 2 years ago
This is a pretty badass boiler!
I would love specifics on how to build one.
mycoptah 2 years ago
I want to make a small thermal power plant for a school project (and also for fun), I saw many images of small monotube boiler, but which are high pressure, I need 50 psi to 80 psi to get 500 to 800W using a turbine tesla with 10 disks of up to 14 cm. I need a pump to inject water in the boiler monotube? If yes, how much power the pump?
fernandesilyt 2 years ago
That is a very nice unit! Well done! I am in the process of building a down draft gasifying hot air furnace as well. I Have to wonder how much energy has been wasted over the years when I see a smokey chimney from other houses. I would like to learn more about your smoke eating machine.
steviebellbuilt 2 years ago
Great job man!
It's a nice looking boiler. How long did you spend building it?
cheers
pjmasterzz 2 years ago
You don't need wood pellets. Wood chips, saw dust, leaves, anything that burns.
LynxSteam 2 years ago
where do you buy wood pellets in australia?
erikals2 2 years ago
GREAT JOB!
Did I miss something in you other vids I thought u using a coil of copper as a boiler how does the spark plug tie into that. also could you give us parts list and schematic of your control system in the next eppisode
either way thank you.
gabrielou812 2 years ago
Thanks for the compliments.
Yes, there is a coil of copper tubing about 175 feet long. The spark plug is used as a means to complete a low voltage circuit when water is present in the tubing circuit just before it enters the evaporator section.
Yes, I will share the circuits, and schematics when I am satisfied. I have attempted to keep things as off the shelf and simple as possible.
LynxSteam 2 years ago