Thanks for your comment. Sorry for the lack of info... These videos were shot in the midst of my wife leaving me and my father loosing his battle to cancer. I dedicated this video to him as he was fighting for his life in the hospital. He unfortunately did not make it God rest his soul. After my divorce is final I hope to start of the new year 2011 with an HHO Bang!!! I will have all the info posted in a stage 6 video. Just hang tight, Dr Franken Zap will be back in the lab soon!
Missing is description of what we are looking at , include please, video with every detail of construction, the voltage and amperage used and what the production is in liters per minute. Your installation needs verbal description and methods of connectiing and include all parts. Kill the music, this is supposed to be a sharing of ideas? If so the music should go and the narrative should be complete to describe all aspect of installation and function..
have you tried to hook up a tesla power supply to the coilsyet? you know ..hi volts low amps L-C circuit with the output from the condenser (s) going to the coils. would be exciting to see if really hi voltages would stimulate greater gas volume at low amps. with meters showing whats going on and a lpm test with a bottle. thanks for the good vid's
do you know how much is required to run a jeep cherokee without gas? And do you know how much your HHO is producing? I would love to know and quite like your design , I was looking at coils instead of plates and wondered what the output was.
I know a lot of people are worried about amps output but once running I figure the altenator takes care of the electrical side of things and it never really was about that. That is something to refine once the actual generator is perfect.
Thanks! Most of this is built from junk. I had to buy some check valves and hose conectors and such, but dumpster diving is a must for a low budget HHO project!
Thanks for the props and info. Things have been slow with the tinkering because of my dad and all, however I still have some fine tuning to do to this project. Keep watching and thanks!
You should be able to get even more production if you put one of the feed points on the opposite end of the cell from the the other. (positive at the top, negative at the bottom or visa versa)
It should not be too hard to insulate the center tap, run it to the bottom and feed from there.
Thanks for the props and info. Things have been slow with the tinkering because of my dad and all, however I still have some fine tuning to do to this project. Keep watching and thanks!
did you try herbal medicine to your dad instead of chemo or rad therapy?may God bless his soul,at least no more pain for him.
tubongsigaw 1 year ago
DEKAROHHO... SHUT UP!!! Unles you have anything good or positive to say SHUT UP!!! I don't have time to listen to people like you!
DrFrankenZap 1 year ago
Kill the music. things being presented are supposed to be inventive, not a selling of your taste in music. Information is needed not music.
DEKAROHHO 1 year ago
@DEKAROHHO DEKAROHHO... SHUT UP!!! Unles you have anything good or positive to say SHUT UP!!! I don't have time to listen to people like you!
DrFrankenZap 1 year ago
Thanks for your comment. Sorry for the lack of info... These videos were shot in the midst of my wife leaving me and my father loosing his battle to cancer. I dedicated this video to him as he was fighting for his life in the hospital. He unfortunately did not make it God rest his soul. After my divorce is final I hope to start of the new year 2011 with an HHO Bang!!! I will have all the info posted in a stage 6 video. Just hang tight, Dr Franken Zap will be back in the lab soon!
DrFrankenZap 1 year ago
Missing is description of what we are looking at , include please, video with every detail of construction, the voltage and amperage used and what the production is in liters per minute. Your installation needs verbal description and methods of connectiing and include all parts. Kill the music, this is supposed to be a sharing of ideas? If so the music should go and the narrative should be complete to describe all aspect of installation and function..
DEKAROHHO 1 year ago
@DEKAROHHO DEKAROHHO... SHUT UP!!! Unles you have anything good or positive to say SHUT UP!!! I don't have time to listen to people like you!
DrFrankenZap 1 year ago
have you tried to hook up a tesla power supply to the coilsyet? you know ..hi volts low amps L-C circuit with the output from the condenser (s) going to the coils. would be exciting to see if really hi voltages would stimulate greater gas volume at low amps. with meters showing whats going on and a lpm test with a bottle. thanks for the good vid's
AircondGypsy 2 years ago
do you know how much is required to run a jeep cherokee without gas? And do you know how much your HHO is producing? I would love to know and quite like your design , I was looking at coils instead of plates and wondered what the output was.
I know a lot of people are worried about amps output but once running I figure the altenator takes care of the electrical side of things and it never really was about that. That is something to refine once the actual generator is perfect.
wealthfinder192 2 years ago
Thanks! Most of this is built from junk. I had to buy some check valves and hose conectors and such, but dumpster diving is a must for a low budget HHO project!
DrFrankenZap 2 years ago
not bad better than what i got seeing as i only have junk tow work with that i find of the side of the road abandoned
prototype9000 2 years ago
Seems to me that you're only a fine metal
mesh 'partition' away, from developing a
hydrogen only generator.
Love your work and the output that you appear
to be getting.
Blessings, to your father ...
/ChuckD....
roshidude 3 years ago
No! plate are better Put out I seen it here on youtube.
davinpilling 3 years ago
I don't agree, but you must be the expert?
DrFrankenZap 3 years ago
I built one of these in my high school years with 75 alternating 4 inch diameter disc with great success.
glennvtx 2 years ago
how thick is the wire that you used on the coil?
marlog1123 3 years ago
I will be posting all of the info SOON!
DrFrankenZap 3 years ago
Thanks for the props and info. Things have been slow with the tinkering because of my dad and all, however I still have some fine tuning to do to this project. Keep watching and thanks!
DrFrankenZap 3 years ago
You should be able to get even more production if you put one of the feed points on the opposite end of the cell from the the other. (positive at the top, negative at the bottom or visa versa)
It should not be too hard to insulate the center tap, run it to the bottom and feed from there.
Just a suggestion.
Very nice design.
I hope your Father gets better.
Good luck and take care.
lutherp40 3 years ago
Thanks for the props and info. Things have been slow with the tinkering because of my dad and all, however I still have some fine tuning to do to this project. Keep watching and thanks!
DrFrankenZap 3 years ago
nice design. have you measured to see how much HHO this unit produces? (liters/minute) how many volts/amps does it use?
sizzlassiei1968 3 years ago
I will be following up with all of the stats as soon as I have the time. SOOOON!!! Keep Watching!!!
DrFrankenZap 3 years ago