I have a question, Im using currently Pakcet Tracer 5.3, Ive a problem configuring the NTP server on the multilayer switch that has connected the IP phones, I have whats necessary for the ntp to work but the server wont give me the current time for that switch, and also do you know wh tI have to configure on the ip hones so that they stop displaying on their screen "configuring CM list" ?
@Niaggalover Since Packet Tracer is a simulator I'm not sure how accurate the results are. I would suggest GNS3 for better results since it a hardware emulator using real software vs emulating software. With that said, if you have your ntp server configured, remember to add "ntp master" so the switch will function as a server. As far as phones showing "configuring CM List" , that means they are not registering with CUCM or CUCME. Make sure option 66 and/or 150 are set properly on DHCP
Hey thanks for the reply. Again, great video series for CME. Highly recommend.
Might consider FXS/FXO, gateway to PSTN config videos. Connecting the CME to PSTN to make actual outside calls would be great [without or even with Unity].
@medialook15 Thanks! The company I work for is a gold partner with Cisco and I was fortunate enough to get service contract and partner association (as an employee) with my CCO login so I didn't have to pay anything. Prior to that every place I looked for a Smartnet contract was by "request a quote" so I'm not sure how much they actually cost.
@sadiqsuzi I actually did a video last week, just been having some codec issues trying to get it posted. I'll try to get posted this week but in short, all you need is VMWare on a machine to run CUCM or CUBE and the rest should integrate with your existing environment. My current CCVP lab as 4 phones, 2 IP Communicatiors, a MGCP gateway to a 2801 that has FXO and PRI interfaces for termination. For being on VMware it is decent but i still like CME a lot better! :)
@tenzinpalden Yes. I had to take it twice though. The first attempt I only missed by 5 points and was in-part because the particular simulation content I had is nowhere in the book. I had to play around on a UC500 via CCA afterward to figure out how to do the tasks I was given on the simulation. However, I re-took it the following week and had a different simulation which inadvertently was pretty close to some of these vids I made and got a 970 on that one.
Thank you! If you're new to telephony, this cert can be very overwhelming. I had a slight advantage because Ive been in traditional TDM telephony industry since 2001 and started working with VoIP in 2005. However what I like about this cert is whether you have a data or telephony only background, this exam covers both very well and bridges the gap. Just take one topic at a time and understand it thoroughly before moving on. Good luck with your studies and enjoy the ride!
Dear please would you tell me any ccna voice simulator that i can use ? likewise for ccnp track we have BosonNetsim & Packet tracer, but unfortunately i haven't found one for ccna voice so please guide me in this regard.
corebts.com
habibee2u 10 months ago
I have a question, Im using currently Pakcet Tracer 5.3, Ive a problem configuring the NTP server on the multilayer switch that has connected the IP phones, I have whats necessary for the ntp to work but the server wont give me the current time for that switch, and also do you know wh tI have to configure on the ip hones so that they stop displaying on their screen "configuring CM list" ?
Niaggalover 1 year ago
@Niaggalover Since Packet Tracer is a simulator I'm not sure how accurate the results are. I would suggest GNS3 for better results since it a hardware emulator using real software vs emulating software. With that said, if you have your ntp server configured, remember to add "ntp master" so the switch will function as a server. As far as phones showing "configuring CM List" , that means they are not registering with CUCM or CUCME. Make sure option 66 and/or 150 are set properly on DHCP
wmx99 9 months ago
Hey thanks for the reply. Again, great video series for CME. Highly recommend.
Might consider FXS/FXO, gateway to PSTN config videos. Connecting the CME to PSTN to make actual outside calls would be great [without or even with Unity].
medialook15 1 year ago
@medialook15 No prob. Yeah I plan to have PRI/CAS, FXO, and FXS configuration examples for CME as well as CUCM in the near future.
wmx99 1 year ago
wonderful video. btw who did you buy your support contract from and if you don't mind sharing how much?
medialook15 1 year ago
@medialook15 Thanks! The company I work for is a gold partner with Cisco and I was fortunate enough to get service contract and partner association (as an employee) with my CCO login so I didn't have to pay anything. Prior to that every place I looked for a Smartnet contract was by "request a quote" so I'm not sure how much they actually cost.
wmx99 1 year ago
this vid is great and please can someone tell me how can I setup a virtual lab for ccnp voice as I did with ccna in gns3 and packet tracer.
sadiqsuzi 1 year ago
@sadiqsuzi I actually did a video last week, just been having some codec issues trying to get it posted. I'll try to get posted this week but in short, all you need is VMWare on a machine to run CUCM or CUBE and the rest should integrate with your existing environment. My current CCVP lab as 4 phones, 2 IP Communicatiors, a MGCP gateway to a 2801 that has FXO and PRI interfaces for termination. For being on VMware it is decent but i still like CME a lot better! :)
wmx99 1 year ago
did you pass the cert?
tenzinpalden 2 years ago
@tenzinpalden Yes. I had to take it twice though. The first attempt I only missed by 5 points and was in-part because the particular simulation content I had is nowhere in the book. I had to play around on a UC500 via CCA afterward to figure out how to do the tasks I was given on the simulation. However, I re-took it the following week and had a different simulation which inadvertently was pretty close to some of these vids I made and got a 970 on that one.
wmx99 2 years ago
Congrates!!! I have just started my Voip class and Just over whelmed at this point . YOur vid is helpful,thank you.
tenzinpalden 2 years ago
Thank you! If you're new to telephony, this cert can be very overwhelming. I had a slight advantage because Ive been in traditional TDM telephony industry since 2001 and started working with VoIP in 2005. However what I like about this cert is whether you have a data or telephony only background, this exam covers both very well and bridges the gap. Just take one topic at a time and understand it thoroughly before moving on. Good luck with your studies and enjoy the ride!
wmx99 2 years ago
@wmx99
Dear please would you tell me any ccna voice simulator that i can use ? likewise for ccnp track we have BosonNetsim & Packet tracer, but unfortunately i haven't found one for ccna voice so please guide me in this regard.
Thanks alot for a very nice video
PakissPower 1 year ago
excellent please continue on
deryasarac 2 years ago
Excellent tutorial
Thank you
Brief and general -all we needed
deryasarac 2 years ago