I have an 82 honda xl125, and when you rev it up and let the throttle snap back closed, sometimes it goes to a nice perfect idle, but sometimes it just dies dead as a doornail . I have messed with the ignition and gone through the carb. several times but it still does it. Do I need to toss the carb and just get a new one ? Anyone have any ideas ?
my bike is the same mate, the carb is done and pumps way to much fuel through. the mix is too rich. what I have done until i get a carb kit is take of the stock air box off and replace it with a small pod filter, they are like $30 (australian) on ebay... At least you can kick start yours, i gotta roll start mine every time!
my friend has the same bike and he got it for $20, but the thing is the spark will go for a second or two then goes away, we tried adjusting the timing but the samething happends. so now ima buy it of of my friend and get my uncle to fix it with me, any idea where to start first to fix the problem with the timming?
@CoolSypherz76 The bike uses a Points style Capacitive ignition system, Which is under the flywheel, The points gap usually gets dirty/corroded, You can access them through the holes in the flywheel, Use a paper nail file to clean between the contacts and it should take care of it.
tessier1234 yoh man i have the same type of bike idk if u have this problem wtih ur urs mind run fine i just got the motore clean up but my trottle dont work i have check everything cant seems to get why its arnt working if u have any answer what to check next that will get its to rev agin let me know thx
sounds rich...slow revs and no idle...i had a newer xr80 that i got non running for 50 bux...tht lil bike carried my big ass around (210) for lik a week befo it bit the big 1ne...and still all it needed was a head gasket...bought for 50 non running...sold for 75...really not running lol
Hi Airport , You mentioned it was seized , I presume you stripped down , and removed everything , bu theoff chance di d you remove the timing cog on the crank as well , as these , werent keyed , so if you did , you may have put the cog back on the wrong setting , being for m,emory either the highest point of the gear TDC or the lowest TDC . That motor should be screaming its guts out
heck no. i got a 1981 xr80 i ride a lot. it might be a little small for you, but youd love it. i have mine on craigslist, cause i want a bigger(in power) bike. look it up
very nice bike. tuneing a bike takes time especialy if it's sitting for a long time. Did you bore it out when you rebuilt it? and what did you all change?
I cleaned em using a cheap cardboard nail file that I cut in half. It is running better now than it was in that video, Since then the shifting problem is fixed, and the clutch works.
hey ppl.ive got an old xr80 which im fixin up.not sure wa year it is but its old,the colours on it are...tank nd mudguards are orange nd side plastics are white nd got a blue seat if this helps??ive got a problem wiv the wirin,dnt know wat wire connects to what.if any1 knows please mail me.cheers
Attention Whore. Who gives a fuck what bike you have? Bet ya don't have the balls to take it WOT. PS, Old Bikes are fun to mess with. Good to learn new things on too.
I bet ya don't even know how to pull a cylinder head off! Let alone work on internals, Rod/Piston/Crank/Gears.
Yeah, Its been a while since this video, Since then I have rebuilt the bottom end, All 5 gears work, Starts in 1/4 kick. Purrs like a kitten at idle and yeah. It was tempermental in that vid because clutch/gears were siezed up.
You have dirty jets, clean the carb
nhfoos 3 months ago
sounds like the carb is knee deep in sand, plugged jets perhaps?
woodyate 4 months ago
I am getting a 1987 xr80r from my brothers friend all it needs is a master link
MrKorphish 4 months ago
is it cold or does the carb need to be cleaned
zachattack2246 5 months ago
any body needs parts i have em...xr and cr 80....gt80....you name it i probably have it :)
timwecycle 7 months ago
I have the same bike, everything is stock except the tires. It will crank up without choke on the first kick and wont shutoff until its out of gas!(:
Brandonyoung29 8 months ago
does anyone know if this engine will fit in a 1981 cr80 body?
TheJd2205 9 months ago
Just turn up the idle and ride the dang thing a while, wring it out. Will run better.
radishgravy 10 months ago
U keep flooding the carb
Mrtoms98 10 months ago
roughly how much did it cost because i want to restore my 1983 Honda XR80?
Jayman19971 11 months ago
did you paint it?? if you did do you know the paint specs and what kind ill need? thx.
CoolSypherz76 11 months ago
I have an 82 honda xl125, and when you rev it up and let the throttle snap back closed, sometimes it goes to a nice perfect idle, but sometimes it just dies dead as a doornail . I have messed with the ignition and gone through the carb. several times but it still does it. Do I need to toss the carb and just get a new one ? Anyone have any ideas ?
bigrigJim 1 year ago
This has been flagged as spam show
GO SUCK YOUR DICK!!!!
camoskill 1 year ago
sounds like it runs like shit. Wont even idle.
joe735 1 year ago
just keep it reving out and it wont quit ?
shakaroon1 1 year ago
do you want to sell it or trade
brittanybew18 1 year ago
decent bike for it's age is it?
GSRGOPEDRIDER247 1 year ago
get a new carb on ebay for 25 bucks then you wont waste your time kicking it over for 2 minutes
vankyfwa 1 year ago
it keeps dying because ur tapping the gas
bassfisherman1254 1 year ago
i might be getting a 83 xr80
justinchaffin1013 1 year ago
my bike is the same mate, the carb is done and pumps way to much fuel through. the mix is too rich. what I have done until i get a carb kit is take of the stock air box off and replace it with a small pod filter, they are like $30 (australian) on ebay... At least you can kick start yours, i gotta roll start mine every time!
KaneBeutel 1 year ago
ive got a pw80 its sick
moorsey77uk 1 year ago
my friend has the same bike and he got it for $20, but the thing is the spark will go for a second or two then goes away, we tried adjusting the timing but the samething happends. so now ima buy it of of my friend and get my uncle to fix it with me, any idea where to start first to fix the problem with the timming?
CoolSypherz76 1 year ago
@CoolSypherz76 The bike uses a Points style Capacitive ignition system, Which is under the flywheel, The points gap usually gets dirty/corroded, You can access them through the holes in the flywheel, Use a paper nail file to clean between the contacts and it should take care of it.
airportlakesestates 1 year ago
tessier1234 yoh man i have the same type of bike idk if u have this problem wtih ur urs mind run fine i just got the motore clean up but my trottle dont work i have check everything cant seems to get why its arnt working if u have any answer what to check next that will get its to rev agin let me know thx
Tessier1234 9 months ago
@CoolSypherz76 spark timing or valve timing you better get a new coil on ebay
vankyfwa 1 year ago
@CoolSypherz76 Just crank up the idle and wring it out riding it, will probably run better and then you start troubleshooting.
radishgravy 10 months ago
I had a 83 xr 80 just like this one whin I was a kid. Brings back memories whin I used to run from the cops lol. Good job keep it up.
lazie82 1 year ago
zu viel oil in benzien
DALIBORE7 1 year ago
sounds rich...slow revs and no idle...i had a newer xr80 that i got non running for 50 bux...tht lil bike carried my big ass around (210) for lik a week befo it bit the big 1ne...and still all it needed was a head gasket...bought for 50 non running...sold for 75...really not running lol
bentboybbz 1 year ago
it shound nt be smokin like tht
vankyfwa 1 year ago
i have a seat 4 that dike i can sell u
xXworld1Xx 2 years ago
@xXworld1Xx hey just looking at this vidio and whanted to know if you still have that seat ? i have a 84 xr80
MegaRolliepollie 1 year ago
sounds like ignition timing and valves... adjust the points
kidonthe300ex 2 years ago
Hi Airport , You mentioned it was seized , I presume you stripped down , and removed everything , bu theoff chance di d you remove the timing cog on the crank as well , as these , werent keyed , so if you did , you may have put the cog back on the wrong setting , being for m,emory either the highest point of the gear TDC or the lowest TDC . That motor should be screaming its guts out
radiorambloke 2 years ago
ShalemH <----
First purchase for any bike is a Service Manule...
Valve lash is .003" or .08mm intake and exuast
Carburetor:
PC10A
92 Main Jet
35 Pilot (slow jet)
1 1/2 fuel screw
Needle 4th from top
Float .787" or 20mm
zlacker73 2 years ago
just picked this same bike up today for $200 and its in great condition..
Nitroheadfool 2 years ago
put some seafoam in the tank and quit reving like that,eep the rpms constant and it will stay running ( dont use a whole bottle)
Zpup95 2 years ago
What is the float setting on this bike? Thanks.
ShalemH 2 years ago
mine souds hilariouse!!!! i bot it and i cracked up cuz dA Ttailpipe wuz broke
MrXxXxXxXxX97 2 years ago
i got a 1980 xr80. needs new tailpipe tho
MrXxXxXxXxX97 2 years ago
heck no. i got a 1981 xr80 i ride a lot. it might be a little small for you, but youd love it. i have mine on craigslist, cause i want a bigger(in power) bike. look it up
videman21 2 years ago
Nice bike man. The older Hondas are great bikes. Too bad some people just neglect them.
TheAlexManVideos 2 years ago
Clean the pilot jet
canammx1 2 years ago
Clean the Main jet
canammx1 2 years ago
its like one more kick each time it stalls to start it lol...nice bike
jencas123 2 years ago
very nice bike. tuneing a bike takes time especialy if it's sitting for a long time. Did you bore it out when you rebuilt it? and what did you all change?
P.S. did you put new valve guids in?
dash9898 2 years ago
STOP IT!!
kevykev38 2 years ago
Word of advice, don't feather the throttle so much with 2 strokes. You'll foul out the plug.
YouraN1993R 3 years ago
Word of advice. Its a 4 Stroke. Not a 2
airportlakesestates 3 years ago 14
My bad, I thought it sounded like a 2 stroke not a 4. Shitty sound quality video.
YouraN1993R 3 years ago
It was poor compression on my part. I had to go from a 300 MB AVI to that.
airportlakesestates 3 years ago
any one that knows dirt bikes should knoe that is a 4 stroke even by looking at the motor and they never made a xr80 2 stroke only cr80
trxhonda125 2 years ago 6
@trxhonda125 damn straight the 2 strokes have the big exhaust that comes down the front
clutch182 10 months ago
@clutch182 and sound completely different lol
ramsrider14 7 months ago
It sounds exactly like a 4 stroke to me.
canammx1 2 years ago
@YouraN1993R Sounds like a 4stroke to me.
cxbra 1 year ago
@YouraN1993R doesn't sound anything like a 2 stroke.
snoop6604 1 year ago
@YouraN1993R Your fucking retarded -_-"
Xstung0nceX 6 months ago
Yeah dude, it sounds nothing like a 2 smoke. And look at the HUGE cylinder head. It's so obvious that it's a 4 stroke.
TheAlexManVideos 2 years ago
FAIL
Jcrongo 1 year ago
@YouraN1993R lol your an idiot how does that sound like a 2 stroke
dinomite3621 1 year ago
the points are still durty ,i cleaned mine with a smoke pack folded up
frazzlefrazzle 3 years ago
I cleaned em using a cheap cardboard nail file that I cut in half. It is running better now than it was in that video, Since then the shifting problem is fixed, and the clutch works.
airportlakesestates 3 years ago
yo tengo una 80 xr500 y cada domingo le doy el roll
arizona0180 3 years ago
nooo maames la miaa es 84 i no prende la motoo qe pedo con esa mamadaa
laola45 3 years ago
hey ppl.ive got an old xr80 which im fixin up.not sure wa year it is but its old,the colours on it are...tank nd mudguards are orange nd side plastics are white nd got a blue seat if this helps??ive got a problem wiv the wirin,dnt know wat wire connects to what.if any1 knows please mail me.cheers
gunther92 3 years ago
that motor seems too tight to me....
turn2brew 3 years ago
Remember, The clutch was locked and it was Stuck in first. Reason it seemed too tight.
airportlakesestates 3 years ago
how much would an old xr like that go for un restored?
theleakytaps 3 years ago
nice bike man
217dru 3 years ago
i have a 1980 model xr80 too. except mine actually runs haha. on original top end, etc etc .. everything... tough :)
chook0162003 3 years ago
Well this one Runs now. It was a project bike, Just for fun to see if i could get it running. It was sitting for over 15 years!
airportlakesestates 3 years ago
i have an 87 and man does it not look as good as that, runs alot better tho. doesnt have a lot of comression, might rebuild the top end
rcjg24 3 years ago
This thing has too much compression! this video was after a rebuild. Shifter problem was from rust/burnt on oil on the shift star and clutch plates.
airportlakesestates 3 years ago
its like my !:P
matpich1 3 years ago
u guys r fags thats a small bikes idk who the fuck likes those pieces of shit i have a 2007 honda trx 700xx fuck u
xr805555 3 years ago
nice, how fast does it go? my bro just baught a 2007 rm 85 for 1300 used, nd it whips.
TheSnakeGuy1 3 years ago
rm85's do kick ass, i have a 2006 :)
ncd10 3 years ago
wow uhm Try riding one and uhm ading some crap to it they're just as fun as the big guys
zminker11 3 years ago
Attention Whore. Who gives a fuck what bike you have? Bet ya don't have the balls to take it WOT. PS, Old Bikes are fun to mess with. Good to learn new things on too.
I bet ya don't even know how to pull a cylinder head off! Let alone work on internals, Rod/Piston/Crank/Gears.
airportlakesestates 3 years ago
i got the same bike :]
MK3K4V 3 years ago
had the same problem this morning then it burned to the ground
countryboy4320 3 years ago
hey.. would it be safe to run without a side cover like you are?
kidonthe300ex 3 years ago
Yes, it would be! Just for looks
airportlakesestates 3 years ago
i got the same bike they r pretty tuff lil bikes
94ctk94 3 years ago
ive got the same bike .itll start right up in one kick cold start.your bike still nedds a lot of work
ajjock11 3 years ago
Yeah, Its been a while since this video, Since then I have rebuilt the bottom end, All 5 gears work, Starts in 1/4 kick. Purrs like a kitten at idle and yeah. It was tempermental in that vid because clutch/gears were siezed up.
airportlakesestates 3 years ago
PS take a look at my newest vids, Thats my latest project...
airportlakesestates 3 years ago
is that a 4 stroke or a 2 stroke caus i just got the same bike 4 free
countryboy4320 3 years ago
4 stroke.
Good little bikes. I have fixed the clutch/shifter, Appears i will need new clutch pads soon due to slippage.
airportlakesestates 3 years ago
me too!
MK3K4V 3 years ago
lol
nice bike :)
carpathianslave 3 years ago