Airsoft custom DIY ep 1 Masterkey

[ARandomJoe]

Your method is very similar to mine, as I am about to hacksaw the part that the pistol grip hides off. Although, instead, I plan on keeping the outer case/rail set on the shotgun, and put two scope rings on it. Then you can attach the gun directly to the outer barrel of your assault rifle, and I think it looks a bit more professional since gluing it on can look sloppy if done incorrectly. Oh, and for my method, make sure you you buy scope rings with the correct width for your outer barrel!

[oreomonsterful]

you should put a gas pistol under it

[TheeAcornLads]

You sound like Ernie off of Sesame Street

[bestpctips]

@CODXXGOD1 thats what im gonna do for my first attempt

[CorporalWalrus]

G&P masterkey kit on redwolf for 120$, but its for maruzen m870 shell ejectors :/

[spartan4461000]

why dont u just use a screw driver and make holes in the "outer shell" and bolt the shot gun into place on the hand grip, u wont have to saw off the RIS rails than, and i dont think hot glue is going to hold well (plus it looks pretty getto).

[Fullmetal9876]

@spartan4461000 I tried that first but the problem is after 10 games of using it, the handguard and the outer shell crack to the point where they fall apart. With the glue the strain is put all across the shell and handguard instead of just three focal points and won't crack. as for durability i've been using that same shotty for over a year now and haven't had an issue... Until I got knocked over and fell on it and snapped the front end off.

[Fullmetal9876]

@spartan4461000 As for looks. yah my glue job there sux but after i painted you can't tell it's glued on unless your holding it and looking at it

[AnotherGaisle]

A new Masterkey conversion kit is on Evike now, but for $200.

Your idea is probably better.

[tacticalnerfmoder16]

isnt that the s3p2, i has 1, and its mah primary,

ive had mah eye on an m16, m4 rifle,

and i was thinkin of this, and i was lookin for tutorial, and i can get the handle off mine, i did that to paint it cuz it had nice camo, along with the pump,

and i also want a removable 1, so im lookin for hardware stuff, sumthin that attaches between da 2 rails, i dont like the hot glue sulution,

[Mortimore22]

im gonna see ifi can do this with a sd87ga

[Fullmetal9876]

@Mortimore22 that would work well a it has the same set up as the m3000. just a different stock

[BaffledOrange]

thinking of making one of these but it should work out cheaper its gonna work similar to homemade tripmines which are on youtube so it will have a proper shotgun spread effect will have a vid up when i get it done :)

[Fullmetal9876]

@BaffledOrange cool I'd like to see it though wouldn't it be one shot reload one shot reload where mine does 20-30 before you reload

[BaffledOrange]

@Fullmetal9876 yea it would but that in it's self would be more realistic because most masterkey shotguns are shell loaded to make them more compact also yours will be single shot and mine will give a large spray to take out multiple targets with one shot

[Fullmetal9876]

@BaffledOrange I guess but all shotguns including masterkeys can hold multiple shells and i didn't put this in the video as the point is to make a cool yet not so expensive (under 30$) add on to your gun. but you can make this with a crossman stinger or other stinger clones which use shells and shoot multiple bb's at once but they cost like 130$ - 200$ to make. dependimg on the parts

[Shwanksta101]

ive been planning on doing this to my assault rifle but im using a medal body shot gun and for the mounting i used the pre exsisting holes were the railing at the bottom was and then drilled holles in the top of the shotgun frame and mounted it using the new drilled holes. it works quite well the only thing you may have to worry about is if you were to smash it for instance it might damge the rifle itself considering the underbarrel is securelly mounted to the frame of the body.

[Fullmetal9876]

yah thats why i recomend doing it my way as the body or exterior casing can get serious damage and my way spreads the strain over the entire casing and like 8 scews so it lasts a while but the area around the screws (on the case) can crack so i usually reinforce them and its the rail that take the brunt of you rifle bashing force (which is usually metal) but since i changes guns to an A-16 (which has has the holes) i merely hot glued the entire thing to the grip as most upgrade are RAS now :P

[ZACY29]

would this work with AK47 models?

[Fullmetal9876]

@ZACY29 solong as it has a rail system (well you coud just glue it directly to the body but it'll work either way) so yah it'll work

[Legokink1]

could make this rail mounted instead of hot glued?

[Fullmetal9876]

its is rail mounted you took a remouvable rail and mounted it on the gun upside down do remember what i put on youtube is for those with a small buget the mount one use a trishot (120$) an mounts (which cost 50$ for two) this one rings in at 30$-60$ so i put it on instead

[Mortimore22]

you probably could just gotta mod the shotgun alot

[Fullmetal9876]

@Mortimore22 thats what you do. you take off the stock cut down the body and mod the outer shell

[btaoftfotpthm]

yo arent you that guy who broke the fishtank?

[Fullmetal9876]

no im not

[DoubleyouCeeGee]

lololololololololololololololo­lololololololol

[PolTehPwnage]

Agreed.