I Fixed The Weedeater Lawnmower !!!!

[megaman5043]

FFFFFFFFFFFFFFFFFFFFFUUUUUUUUU­UUUUUUUUUUUUUUU where can i find one the dosent hav a bag (can't hav one on) cause a friend gave me one like that n its cloged me n my dad gon fix it tomaro

[1972FordF150]

@megaman5043 Try Craigslist or something, Walmart sells these new but there pieces of crap

[youaxeng]

How you remove the exhort

[1972FordF150]

@youaxeng You take gloves and twist the muffler counter clockwise and if it won't come off by hand use something that will wrap around it to take it off.

[traxxastmax1]

you said in one of your vids that this mower is 50.00 bucks what store did you buy it at for 50.00 please please respond.

[1972FordF150]

@traxxastmax1 I bought it at walmart and it was at the end of the year and it was a floor model.

[230910bella]

i have tht one, starts firs pull every time, somtimes no prime. original spark plug

[1972FordF150]

@230910bella That's good. Mine was a pos but I sold it and the new owner has none of the problems that I had with it.

[Rarrin9378]

man that thing was a piece of crap

[1972FordF150]

@Rarrin9378 Yes it was LOL

[Rarrin9378]

@1972FordF150 hahaha

[Rarrin9378]

They must have had a half-assed lower level employee from sector 7-G build this lawnmower.

[1972FordF150]

@Rarrin9378 LMFAO ! and the guy must have been SCREAMING "WUMBO" when he was putting it together too

[Rarrin9378]

@1972FordF150 probably. LOL

[nonamejoe56]

Good job, most people would be too stupid to figure that out

[1972FordF150]

@nonamejoe56 Lol thanks !

[corny678]

5 stars

[1972FordF150]

thanks !

[corny678]

glad you got it fixed!

[1972FordF150]

Yup... me too :D

[philldholes]

Its an old Briggs they're good motors. Its amazing how little compression they really need when you think abou tit because if it ran long enough for manifold bolts to get finger loose and it ran until then. More fuel always seems to be the remedy to rough idle. haha

[1972FordF150]

the mower is a 2006...lol and I only used it part of this last summer. And yeah they don't need too much to run. And this one has about 95 PSI I have to check it again. I forgot what it was. and the bolts we're just kinda loose enough to tighten them with a wrench. but the shroud bolt what the heck.... I have had that same bolt come out on a different mower before while I was mowing with it lol but those seem to vibrate loose over time anyways on all mowers so... yeah.

[TNJfarm]

Yea iv'e noticed that on those cheap weed eater mowers, that those screw on the outside by the intake manifold come loose a lot m friends alans does it all the tiem and has to tighten them up a lot.

[1972FordF150]

Hmmm. Put service removable loctite on them.

[TNJfarm]

haha ya

[1972FordF150]

i had the front shroud bolt COME OUT once on a different mower in 2008 when I was mowing with it. At a glance I said HOLY SHIT one of my cyl head bolts came out !!!!

[1JessieStender]

Sweet man, 5 stars!! :D

[1972FordF150]

Thanks !!

[TractorWorld]

that will do it!

[1972FordF150]

Yup it will !

[MrMoterKid]

Nice! Not a bad runner! I can't believe that the factory that made it just left all the screws loose!!!

[1972FordF150]

I know me too ! hahaha makes me laugh at the dumbasses that put this thing together. When I put an engine together I get the bolts tight !!

[donyboy73]

5 stars man, no snow there

[1972FordF150]

Thanks !! and nope. I wish there was. Right now there is some bad rain and a lot of wind.