i have a j32a2 in my accord v6, that sounds nothing like it. I used to have a j30a1 when i bought the car, that sounds nothing like it. The single output exhaust...hes got a i4 None the less he would be runnin in limp mode unless he contactd rich on v6p for a custom wiring harness and without it no vtec no speedometer and no reverse lights Rich doesnt make wiring harnesses for civics so that means he had to find a whole donor car and take every ecu, harness, ect out of it. This is full of fail
@Elements153 Its either using the newer hasport mounts or got a smaller intake mani, or im pretty sure the j30 will fit no problem with hood clearance.
if thts a v6 swap how did the hood clear and his take off would've had alot of wheel spin.v6 swap dint catch on till 09 /2010 and hasport jux came out with mounts tht clears the hood to close.tht time they where cutting hoods to clear and the engine should pop up!. check out v6 integra the very 1st v6 swap ever attempted and look if he even has a hood.
@1real4boy wich part of "sounds" you dont read about, i havent saw inside the hood to tell about specs, but i dont care the bad comments, i was telling that is a nice civic, still think that is good, sorry for not explain at all my comment
@ENDORPHMAN..... HASPORT makes mounts but nothing to clear the V6 to let it sit flush with the chassie cause the V6 block is taller and sits higher then any 4's... all the pple i know that has done the swap has went to HASPORT and thats the mounts they use and the only way to go is cut your hood or no hood... plain and simple...
@rxmaster The J-series engines can fit in DC Tegs and EK Civic and not stick out of the hood. But in the EG civics (which I have) the motor will stick out. I've seen guys come close to closing the hood w/custom mounts but the lower the motor the higher the car has to be
@ENDORPHMAN Thanx, but I know that. I have Hasport mounts in my V6 swapped EG and it comes nowhere close to clearing the hood. Research dude, here ill help, j32a.com
honda should see this vid and make a v6 type R civic....with this light chass and mre powerfull engine it can kill many bigger cars with bigger engines .....hmmmmmmm
GUYS ARE PUTTING THE ACURA TL AND RL MOTORS IN THESE ALOT NOW A DAYS. bUT HOW DID YOU GUYS KEEP THE STOCK HOOD? ALL OF THEM IV SEEN HAVE TO HAVE A PEICE OF THE HOOD CUT OUT
haha 92asc, so how many swaps have you done on a civic?? and btw Learn to REad I never stated that swapping a civic w a v6 or yeah even v8 was IMpossible... I did however say u never get it to have the Hood Close Naturally like it came out of factory!!! u dumbass I>D>I>O>T. I Know what A raised hood looks like on a civic and that is not one!! THANK YOU> if you ever want to have a swap off challenge lmk too.. moron.. learn from opmike343 he clearly Read my comment well...
aparrently you've never heard of a machine shop, and how they can shave the intake manifold on one of those j32 or j35s to make the manifold clear the factory hood in any honda or acura.
@92ASC hell to da ya ma dude civette is a BEAST!!!!!!!! and ya your right there is also a video on youtube that shows a TL Type S successfully installed in a civic BBBEEEAAASSSTTT!!!!!!!!
@92ASC Yeah, but the LS1 simply wasn't "thrown" into the Civic. The entire Corvette chassis was modified, then the entire Civic BODY was dropped onto that. Educate yourself before you go and call others idiots lol. Fucking fail.
no.... thats the signal that he gives to the camera man to let him know when hes about to take off....bcuz the car is so fast that sometimes they cant catch the car.
shows what you know idiot. why would you use an H2B. that means ur usin an H series motor, which is is a 4 banger, and a b series tranny. The engine they are using is a J series engine i guarantee you, which are v6. and fyi the hood DOESN"T shut unless you cut a hole in it, modify the hinges so they stand higher to give it more room, or custom mount the engine rediculously low. but then you would bottom out all the time. so the other two are really ur only options to get the hood to close.
bruuuuum bruuuuuum bruuuuuuuuuum briiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim tfr tfr briiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim tfr tfr briiiiiiiiiiiiiiiiiiiiiiim :)
MichaRu16 2 months ago
Vr6
TheEpjake 3 months ago
I wanna hump that civic
666psychadellic 3 months ago
thumbs up of you smiled when you watched this cus i did :D
scalelandy 4 months ago
i have a j32a2 in my accord v6, that sounds nothing like it. I used to have a j30a1 when i bought the car, that sounds nothing like it. The single output exhaust...hes got a i4 None the less he would be runnin in limp mode unless he contactd rich on v6p for a custom wiring harness and without it no vtec no speedometer and no reverse lights Rich doesnt make wiring harnesses for civics so that means he had to find a whole donor car and take every ecu, harness, ect out of it. This is full of fail
JPHalaby 5 months ago
I need this engine!
PEREZCHOOCH 6 months ago
the hood closed ? well, it sounds a little like a v6 so... i dont know... 50/50 on this video...
Elements153 7 months ago
@Elements153 Its either using the newer hasport mounts or got a smaller intake mani, or im pretty sure the j30 will fit no problem with hood clearance.
JacobLee0123 6 months ago
What engine did he put in??
LovensPresume 7 months ago
that is not a v6
advaschechel 7 months ago
Everyone, you have just experienced an orgasm.
gageb94 7 months ago
ok i'm really confused by the road your driving on..... there's cars going around you... then your traveling down that road into oncoming traffic????
Goff86 7 months ago 3
Nice ... :-)
ROCKnROLLA5000 7 months ago
if thts a v6 swap how did the hood clear and his take off would've had alot of wheel spin.v6 swap dint catch on till 09 /2010 and hasport jux came out with mounts tht clears the hood to close.tht time they where cutting hoods to clear and the engine should pop up!. check out v6 integra the very 1st v6 swap ever attempted and look if he even has a hood.
1TommyChan 8 months ago
@1TommyChan thats an ek9, you're thinkin of a 92-95 civic
RippinPopz 8 months ago
sound like shiit LOL
jambonfrais2 8 months ago
Not a v6... J series sticks out
sammy589 8 months ago
@sammy589 thats a EK9.. bigger engine bay. .
585Lowrider 8 months ago
Skip to 0:44
PsuPepperoni 9 months ago
sounds like a j32
EF9zdyne 9 months ago
What motor does this got the j35??
1real4boy 9 months ago
did hasport have mounts for it back in 08?
ej2owner 10 months ago
did hasport have mounts like that back 08?
ej2owner 10 months ago
that shit was sick. I need to get a V6 on this island. That would turn heads.
courtneychiddick 11 months ago
damn that shits fast! sounds like crap tho
yugoterror 11 months ago
sounds like a s2000 swap
kokolistic 11 months ago
@kokolistic an s2000 has a 4 cylinder.
Mnight069 10 months ago
@kokolistic dumbass..
1real4boy 9 months ago
@1real4boy wich part of "sounds" you dont read about, i havent saw inside the hood to tell about specs, but i dont care the bad comments, i was telling that is a nice civic, still think that is good, sorry for not explain at all my comment
kokolistic 8 months ago
@kokolistic Theres a j32 v6 in that car and your saying it sounds like an s2000 f20c which is 4cylinder..and it even says civic V6 in the title
1real4boy 8 months ago
Nice car. Nice Sound. Nice place to live!
garethwalton 1 year ago
how did u manage to get the motor in without cutting the hood? j32?
noender 1 year ago
sounds bad and pulled hard as fuck i want this swap now haha in like a lil crx or a delsol
yungjmoneyboy 1 year ago
quick!!
flooessea 1 year ago
wtf. on coming traffic.. sounds gorgeous btw
DalnamikDesigns 1 year ago
It can be done... all depends on dedication and the deepness of your wallet lol
jahmerikan6 1 year ago 18
u cant fit a j series under the hood.... look up any other j series swap.... its to big
waffleman845 1 year ago
@waffleman845 you DO no hasport makes mounts now so that the engine sits flush right..? so yea it will fit under the hood
Fmxsupasta 1 year ago
@waffleman845 You can!
need to make custom mounts and engine is comming more to the front .
ImMrHonda4u 1 year ago
people put j swaps in civics and del sols and tegs all the time. its not that difficult
jellyboy1995 1 year ago
holy crap lol
foryoutocallmehaha 1 year ago
J swap ?????
35ummpa35 1 year ago
@35ummpa35 lol might as well be, but i think a real jswap is bigger
iMaTThew515 1 year ago
Damn!!! That was a badass engine! This is the 2nd choice for swap. My first choice is an LS V8 like wit the Civette.
chevystud88 1 year ago
Wow still has that unique honda sound to it
UnwrittenEpitaph 1 year ago
Went Ghost
JDMnubi 1 year ago
sounds like my acura legend
poop4256 1 year ago
I normally HATE the sound of hondas... But I will admit, that shit sounded pretty fucking sweet to me..
ki11joy92 1 year ago
@ENDORPHMAN..... HASPORT makes mounts but nothing to clear the V6 to let it sit flush with the chassie cause the V6 block is taller and sits higher then any 4's... all the pple i know that has done the swap has went to HASPORT and thats the mounts they use and the only way to go is cut your hood or no hood... plain and simple...
sirdonicus 1 year ago
HONDA :)
xC0VeNaNTx 1 year ago 12
thats actually pretty badass
rp94cobra 1 year ago
This video blows donkey dicks. Cut out 36 of your 45 seconds, and it will no longer fail.
PSI240SX 1 year ago
ohhhh shit boost control! dum nice.
cheeseburger9418 1 year ago
that muther freaker will get goin,and fast
froggyfireman 1 year ago
how did u fit a v6 in your civic without looking out of your hood?
the sound is damn nice xD
and it seems to have a great traction because of the heavier engine (compared to b16)
rxmaster 1 year ago
@rxmaster The J-series engines can fit in DC Tegs and EK Civic and not stick out of the hood. But in the EG civics (which I have) the motor will stick out. I've seen guys come close to closing the hood w/custom mounts but the lower the motor the higher the car has to be
BoostedSol187 1 year ago
@BoostedSol187 hasport makes mounts dude, lol research buddy.
ENDORPHMAN 1 year ago
@ENDORPHMAN Thanx, but I know that. I have Hasport mounts in my V6 swapped EG and it comes nowhere close to clearing the hood. Research dude, here ill help, j32a.com
BoostedSol187 1 year ago
@BoostedSol187 hasport makes new mounts, and you can easily clear the hood. but your more likely to scrape the shit under your car if its lowered.
ENDORPHMAN 1 year ago
@BoostedSol187 are u sure thay wont stick out? Because that the reason why I haven't swap a j32 in my civic hatch 99
civicallmotor 1 year ago
no v6 i beleave those guys look sorry to be haven a v6 ride didnt sound like it or pull like a v6.
pakilodi 1 year ago
@pakilodi Are you kidding me? Obviously you have no clue what a v6 pulls and sounds like because that was def a v6 no question.
garrett6699 1 year ago
@pakilodi dumbass
lmfao
killerturboek4 1 year ago
it doesnt say what kind of v6 t could be from an accord it would fit perfectly fine under a stock hood
juneya23 1 year ago
New clutch!
ITELADZ 1 year ago
how did you get it to fit
duy856 1 year ago
nice work, i love to see bigger motors in smaller cars. i gave it a big thumbs up.
Scrambler85 1 year ago
shit ! thats quick!! how much for the engine and swap about?
BloodyFingerz 1 year ago
honda should see this vid and make a v6 type R civic....with this light chass and mre powerfull engine it can kill many bigger cars with bigger engines .....hmmmmmmm
faisalabulaziz1 1 year ago
this realy sounds like an vw r32 engine or some
melch1988 1 year ago
Holy shit learn to drive...
shdymoj0 1 year ago
stupid fucks
thecardrawer10 1 year ago
holy shit :)
slavy1990 1 year ago
still love this one
ImMrHonda4u 1 year ago
ohh yeah that's d.r nd that ek sounds nutsz :)
sk8boardVICK 1 year ago
fuck u {sherkynleena} i hope u die, and i hope im there to watch it, puro pinche honda
HighpebeAst 1 year ago
GUYS ARE PUTTING THE ACURA TL AND RL MOTORS IN THESE ALOT NOW A DAYS. bUT HOW DID YOU GUYS KEEP THE STOCK HOOD? ALL OF THEM IV SEEN HAVE TO HAVE A PEICE OF THE HOOD CUT OUT
slapnasty69 1 year ago
NO fucken way! hoods stock bud. Wierd no clearance issues with the motor? dont believe this B.S
cntryman3344 1 year ago
@cntryman3344 reallly depends on what the v6 is out of if its out of an accord it should be ok but yyea no way could it be a v6 from an suv
juneya23 1 year ago
anything is possible nowadays haha its the 21st century. Only open minded people will know its possible.
Dumbpimpstaz 1 year ago
fucking dumb mexicano!! the way he's driving i hope he fucking dies in a car crash.
sherkynleena 1 year ago
it sounds simalur to a lambo
ujusgotownd 1 year ago
whats the 0-60 time
3G4life1990 1 year ago
umm i do belive its a v6 the sound is simular to a j32 swap
youngbuck301 1 year ago
ufff que potencia coooño
manu24v6 1 year ago
haha i like how you fit a v6 perfectly under a regular hood lmfao
Hondamotor303 1 year ago
stupid shit! never v6
roll3rboy 2 years ago
It is a V6 you dumb cunt.
Strogenforcer 1 year ago
Where is this mexico
davybabyson 2 years ago
I Think Dominican Republic since im from there and recognize it
Djtubie 1 year ago
If it revs to min. 8400 nice work. If not: one beautifull civic gone for ever. Too bad :) pozdro ! :)
kostadm19 2 years ago
come on girls its a j series inovative mounts makes it clear the hood. fucken newbs
trixy07 2 years ago
dam his civic is low ! AND on top of top the motor is not showing..how does he do it?any answers would be helpful but no guesses...!
TaLoCc 2 years ago
V6 engine from NSX???
panxoturbo2 2 years ago
@panxoturbo2
no. J32 from an Acura TL, or CL.
@ TaLoCc
Hasport makes mounts for the swap, but the oil pan is only like 2-3 inches off the ground.
TOXIKKOBK 2 years ago
sounds good :)
IIXACEXII 2 years ago
sound is nice...
buterbrodas100 2 years ago
so it is possible to fit that huge motor in their just with the hasport mounts??? possibly a custom hood?
Murchison240sx 2 years ago
@Murchison240sx A logical idea....very possible
CallanBkk 2 years ago
yea you have to have a custom hood for it
LivingToDye 2 years ago
or washer under the hinge bolts lol
integraracer94 2 years ago
its possible for the hood to clear
its been done by moding hassport mounts and using special springs that ebach made just for this swap
pete312able 2 years ago
if he had a j-swap he wouldn't have a hood.
punemax 2 years ago
0:00 i spy a e30 7 series i wana see that race poop all over that civc
jlubez 2 years ago
that sounds nice, but nothing like a j-series. i get to hear the lovely tone of a J everyday and that is nothing like it.
00CG1 2 years ago
thats not a v6
buschdebusch 2 years ago
@buschdebusch it is a V6 VTEC this Civic has a J32 or J35 series Engine swapped.
UrbanCycling 2 years ago
ok...
buschdebusch 2 years ago
damnn
guillermo556 2 years ago
that spells nasty where ever youre from
d15civic 2 years ago
haha even the civic rolls it R's
tokenride04 2 years ago
nice keepin it flush mounted. whats the pan clearance though on the ground?
TOXIKKOBK 2 years ago
Nice sound for once :D
yourmotherrules 2 years ago
dam that civic actually sounds pretty nice
mysrt4303 2 years ago
the sound awesome ... ram dam dam dam
daddybadd12380 2 years ago
sick sound=]
ENDORPHMAN 2 years ago
this is the Dominican Republic, if they did it, why cant you!!!! so if you live in states dont be a pussy cause you got it all...
backtriper 2 years ago 8
Hell to the yeah! DR ftw!
ManuelDr 2 years ago
Damn i love the fuckin sound
JDMkidd89 2 years ago
that's the sound of an Accord V6 Vtec Engine
UrbanCycling 2 years ago
sounds like a v6 to me.
fpatolot01 2 years ago
haha 92asc, so how many swaps have you done on a civic?? and btw Learn to REad I never stated that swapping a civic w a v6 or yeah even v8 was IMpossible... I did however say u never get it to have the Hood Close Naturally like it came out of factory!!! u dumbass I>D>I>O>T. I Know what A raised hood looks like on a civic and that is not one!! THANK YOU> if you ever want to have a swap off challenge lmk too.. moron.. learn from opmike343 he clearly Read my comment well...
1edesin2 2 years ago
aparrently you've never heard of a machine shop, and how they can shave the intake manifold on one of those j32 or j35s to make the manifold clear the factory hood in any honda or acura.
DLoc137 2 years ago
not a v6!!impossible for it to not bee sticking out of the hood.... idiots
1edesin2 2 years ago
While this might not be a V6, there have been swaps done that allow the hood to close. It isn't impossible for it not to be sticking out.
opmike343 2 years ago
throwing a V6 in a civic very possible. Have you not seen the Civette? It's got a 5.7L LS1 V8, it can be done... idiot.
92ASC 2 years ago 20
And the Civette is just the sickest Civic ever I might add. People just don't understand moneys the limit these days.
04saleenboy 2 years ago
true true
ms13goku 2 years ago
@92ASC hell to da ya ma dude civette is a BEAST!!!!!!!! and ya your right there is also a video on youtube that shows a TL Type S successfully installed in a civic BBBEEEAAASSSTTT!!!!!!!!
98dc2gsr575 1 year ago
@92ASC Yeah, but the LS1 simply wasn't "thrown" into the Civic. The entire Corvette chassis was modified, then the entire Civic BODY was dropped onto that. Educate yourself before you go and call others idiots lol. Fucking fail.
wwfbetterthanrwwe 1 year ago
@92ASC the civette has a civic body and thats all the chassis is a corvettes
pOoPdIcK76 1 year ago
you can shave down the intake manifold to make it clear an oem hood...
DLoc137 2 years ago
i have a friend with a v8 in a ae86 corolla which have smaller bays... and it doesnt stick out at all... soo your not so smart
xXTurboEGXx 2 years ago
NICE 2 STEP
SOUNDS SICK...
darrinjeffrieskilla 2 years ago 2
that thing is fast as fuck
sgtdude911 2 years ago 2
damn that sounds nice
Ciera50533 2 years ago 12
damn that sounds ridiculous
rayzian 2 years ago 2
WTF thats fking cool:)
15432Joce 2 years ago 2
is this in mexico
hiluss 2 years ago
dominican republic i think
julix15 2 years ago
no this is DOMINICAN REPUBLIC!
sinegra30 2 years ago
no es santiago Rep Dom.
antraxhp 2 years ago
mexicans cant tune cars. lol joke!
lomejorkehay 2 years ago
wanna see under the hood
sammy589 2 years ago
looks like the light went out for high rev.
BlueRice 2 years ago
no.... thats the signal that he gives to the camera man to let him know when hes about to take off....bcuz the car is so fast that sometimes they cant catch the car.
lomejorkehay 2 years ago
wat kind of v6 from wat car
hatchbackboy22 2 years ago
2003 Acura CL TypeS
ElGavillano 2 years ago
they dont fit under the hood. u have to take the hood off cause the engine is too tall.
sounds like a b16 to me
ChronoCrossKid 2 years ago
shows what you know.... in 96+ civic with h2b and V6 swaps hood shuts fine..
randyyon209 2 years ago
owned
Roddick213 2 years ago 2
shows what you know idiot. why would you use an H2B. that means ur usin an H series motor, which is is a 4 banger, and a b series tranny. The engine they are using is a J series engine i guarantee you, which are v6. and fyi the hood DOESN"T shut unless you cut a hole in it, modify the hinges so they stand higher to give it more room, or custom mount the engine rediculously low. but then you would bottom out all the time. so the other two are really ur only options to get the hood to close.
naz8385 2 years ago
actualy you can get the hood to close if u use a j3.0 k? smart ass?
p.s you no nothing of this swap unless you have or have known sum1 who has
ENDORPHMAN 2 years ago
wrong
milkandmeat 2 years ago
This comment has received too many negative votes show
all you guys are wrong. thats a fucking V8 in under the hood baby!
BlueRice 2 years ago
thats nice.
more videos!
coolfool206 2 years ago
Comment removed
armandoac13 2 years ago
Un motor de un 2003 Acura CL TypeS
ElGavillano 2 years ago
all you see is a red lancia delta drive by, LMFAOOO
smokeytires92 2 years ago 2
Ta jevi, y el swap le tomo mucho trabajo?
ManuelDr 2 years ago
i have to say WOW!
2Gangster4Ya 3 years ago
damn!
btheasian 3 years ago
skip to 48 secs. Don't waste your time with his slow ass positioning.
Garnaden 3 years ago
what kind of honda engine did you put to the civic??????
b16a2y 3 years ago
Most likely the J30.... its the easiest V6 to swap in.
volksracing1 3 years ago
whats the J30 from?
lacklack5 3 years ago
Acura 3.0CL, Honda Accord V6, and the J32 Acura CL
volksracing1 3 years ago
i would love to hear that straight piped
elementskater69 3 years ago
that is a badass civic!! sounds mean as hell
fastlife1688 3 years ago
olle man cual mounts tu usaste
jordanelmvp 3 years ago
eso fue una vaina custom.. pero los mounts ya lo hacen en una compania ahi ke se llama hasport
kevinturbo 3 years ago
The sound is like BMW M3
dasmarkus1986 3 years ago
What mounts did you use??
trixy07 3 years ago
u can get the mounts for this engine on ebay ,they are call hasport v6 for civic , the guy who posted the video told me
jordanelmvp 3 years ago
omg i loooooove that sound ... if i was in that civic i'd be like >> WHERE THE VW AT HAHAHAHAHA ( probably on fire hahaha )
krestalbone 3 years ago
sick civic.. great sound.. ;)
s3thmaster 3 years ago
out of all the v6 civic vids ive seen this is the best one. That car gets moving and is not sitting there spinning the tires.
jnikgar 3 years