I have an e revo and my suspension isn't right. When I have the pushrods all in the same hole, the front sits higher even when i pick it up. The only way I could fix it was put the front in the middle hole, but someone told me not to do that. Please Help!
I want to put a mamba monster in mine but I don't have that kind of money. I just want to buy a velineon and have wheelies on command. I have some 6 cell 7.2v 5100mah batteries. Could it work?
If you want to run stock speeds 32-35mph and gear it low enough it will hold up, read the comments below. Spend the Money on the MMM combo, 250 on ebay.
What's with the MMM thing, you mean the Monster max setup (the one with 2200 kV and 2650 kV motors) or something else? Because I can't find anything that stands for MMM in Castle.
Also, what ESC/Motor are good (or the best) for racing?
yes the ESC is the Mamba Monster Max.. the best combo for racing is the MMM 2200 combo for the most part. Depending on how much you want to spend you can get higher voltage equpiment but it's really not necessary. Thanks
I believe 7xl refers to one of the cheap motors from Feigao, I can't remember what exactly which kv the number means but the xl means it's the biggest size motor. I've got one of them in my revo but i can't remember which number i went for in the end : (
MM esc can work with a BEC running 4s lipo... but no MM motor will withstand this config. Not even a 4600 for very long. MM is actually a smaller size motor than the velineon, the velineon has quite a bit more torque than the regular MM's. Get the right stuff the first time to save money down the road :)
I wouldn't really recommend this setup, but yes with one vxl motor you only need 1 battery unless you ran a pair of 3s lipo's in parallel for longer run times. This setup is only good for about stock speeds and be mindful of temps. Highly suggest going w/ the MMM combo from Castle.
hi,what is yours gering,im thinking to put 0ne of thous VXL3 brushles to new e-revo.i want to get from it obout 35-40 mph.that is ok spead for my to have fan.please ansver.thanks
hey dude how did u make that, like does the emaxx transmission just fit on the revo 3.3 chaisis and ?...do you think you can make a replika of this but with no electronics, and ill buy it off oyu for the price of all the parts+parts+shipping? or give ma a list of parts you used and how/where u used them?
is that car you were runnig lighter than a stock revo waith a single cell? and b how much?... and if i went with the vxl in a stock e revo do you think it will pop wheelies?
i was wondering why you dont recommend racing with this? i run almost 50mph with my stampede vxl on 8 cell 4200mah pack those 40mph wheels suck cause then she walks and baam cartwheel galore lol
Heat will get the best of you pushing it in a real race... that is all eventually the heat will start demagnetizing the rotor and she will be lost.. trust me, I did it ;P I would pick up a Neu 1515 motor (2.5d is an awesome racing motor! The 1y and 1.5d are also solid choices.
The max u can do is 36 miles or it will overheat lol. Its called a fan. U can easily do constant 70 mile+ as long as u have a good fan. Cus wats the point of doing slower speed than a stock E-revo does. I have a stock 1,and I do like 40 miles.
Sorry boss, a stock titan 550 setup running at 40 will be dead FAST.. LOL. The point wasn't anything other than it would work if it had to. I run a Neu 1515 1.5d capable of 50mph on a 4s lipo config, over 60 w/ 6s :P Brushless = no burnt titans as well, those titans die fast where the brushless set to the right speed the little single velineon would get you the same top speed, and last a VERY long time.
This was with a Maxamps 3s2p 8000mAH lipo. Even with this config the most you can do safely with the velineon motor is about 36mph, any more and you'll be overheating constantly.
Just keep it geared around 35mph and it will hold up fine.
May want to snag a Medusa 70mm 2200kv motor when they release in a couple weeks.. running on 4s lipo it will be amazing... and they are only 120 direct. Castle is about to drop their v3 MMM that is ready to go or you could always use a MM w/ a BEC to run the 4s config.
ok thanx but untill then i will jus run the vxl and do you possibly know the stock pinion and spur of the new e-revo or if you dont what gears should i run to keep it cool like how many tooth spur and pinion do you suggest
Just got an Emaxx (older one) with Feigao 9xl and BK ESC. Definitely going to buy an E-revo and swap the stuff into one. The Emaxx gets the E-Revo gear or I'll just sell it LOL. Great vid and nice neighborhood. :)
Check my recent videos, my Neu 1515 1.5d on 4s does about 50, on 6s with out changing gearing I was at 62 gps'ed. If I drop the spur to 54t I'll be at 70mph w/ my erevo :)
You should see it with my Neu 1515 1.5d, on 4s there is no nitro that can keep up with me let alone when I strap in 6s! LOL this toy ownz the nitro, but at least you have the nitro sounds and nitro mess to clean up :)
It takes a bit of dremmel work and a small brace to make it 100% solid. Took a few hours at most. Over on traxxas's forum if you search for "erevo revolt" you will see my entire conversion process.
i set up my revo with a single velineon and it's amazing. i tried it with a mamba max with the 5700kv motor and it got waaay to hot waaay to fast. (both setups with 11.1v lipos). Velineon's the way to go.
what kind of temps did you see with this? i know in my maxx geared for the speeds i got it was HOT, but geared for the speeds in the video, what kind of temps did you see?
with a vxl system in my e-maxx i broke 45 with it. but it was hot and didnt get much run time. and a mamba max, feigao, and twin 2s lipo packs would cos ta lot mroe than a vxl on 3s. but i wouldnt recomend the vxl. its not the best thing for a heavy revo...
I would only use this motor geared for 35mph, it will be pretty torquey and it will last for a good amount of time. Yes, stick with a 3s lipo config for max voltage and lowest temps. It wouldn't cost much more for a better setup though, a mamba max esc with a castle creations external BEC on a Fiegao 8XL and two 2s lipo's (4s in series) would be a MCUH better config and get you around 45mph.
what gear you put mine dont do wheelie
jason1786 11 months ago
@jason1786
put a 3s lipo in it and it will
jowilson275 10 months ago
What body is that?
essegeo 1 year ago
I have an e revo and my suspension isn't right. When I have the pushrods all in the same hole, the front sits higher even when i pick it up. The only way I could fix it was put the front in the middle hole, but someone told me not to do that. Please Help!
TheChris1696 1 year ago
I want to put a mamba monster in mine but I don't have that kind of money. I just want to buy a velineon and have wheelies on command. I have some 6 cell 7.2v 5100mah batteries. Could it work?
TheChris1696 1 year ago
thats one b.a shell
43Wyattlong 1 year ago
about the same speed as cheaper twin Kershaw 700 HO motors?
VideoGamePlayer12 1 year ago
thats sweet dude!!! ive been waiting for someone to put a vellieon in their e revo!
erevofreak96 2 years ago
where do you get your body and can the wing fit when it is on
rcdudes3475 2 years ago
so i can take the 2 titan motors out and put 1 velineon brushless in???
hw6743 2 years ago
If you want to run stock speeds 32-35mph and gear it low enough it will hold up, read the comments below. Spend the Money on the MMM combo, 250 on ebay.
stumblinh 2 years ago
How did you make that esc mount? Could you send me a few pictures of it? Id like to use that with my truck
motoSX125 3 years ago
What's with the MMM thing, you mean the Monster max setup (the one with 2200 kV and 2650 kV motors) or something else? Because I can't find anything that stands for MMM in Castle.
Also, what ESC/Motor are good (or the best) for racing?
PlxDie 3 years ago
yes the ESC is the Mamba Monster Max.. the best combo for racing is the MMM 2200 combo for the most part. Depending on how much you want to spend you can get higher voltage equpiment but it's really not necessary. Thanks
stumblinh 3 years ago
I believe 7xl refers to one of the cheap motors from Feigao, I can't remember what exactly which kv the number means but the xl means it's the biggest size motor. I've got one of them in my revo but i can't remember which number i went for in the end : (
jon2cool 3 years ago
what is 7 xl
martilana 3 years ago
thanks but mm is like 2x the price what mm u got
martilana 3 years ago
MM esc can work with a BEC running 4s lipo... but no MM motor will withstand this config. Not even a 4600 for very long. MM is actually a smaller size motor than the velineon, the velineon has quite a bit more torque than the regular MM's. Get the right stuff the first time to save money down the road :)
stumblinh 3 years ago
coz u only got 1 motor do u only need 1 battery
martilana 3 years ago
I wouldn't really recommend this setup, but yes with one vxl motor you only need 1 battery unless you ran a pair of 3s lipo's in parallel for longer run times. This setup is only good for about stock speeds and be mindful of temps. Highly suggest going w/ the MMM combo from Castle.
stumblinh 3 years ago
u should make it fwd
carsrule12 3 years ago
just a little?
guineapig41494 3 years ago
funny, just a little torque! jk
retnuh2010 3 years ago
hi,what is yours gering,im thinking to put 0ne of thous VXL3 brushles to new e-revo.i want to get from it obout 35-40 mph.that is ok spead for my to have fan.please ansver.thanks
baconsendwich 3 years ago
I'll buy that car off you not including batteries or radio system? Plz!
mattrox1221 3 years ago
Sorry it has long since been converted to a Neu 1515 with Castle's Monster ESC (mmm).
stumblinh 3 years ago
hey dude how did u make that, like does the emaxx transmission just fit on the revo 3.3 chaisis and ?...do you think you can make a replika of this but with no electronics, and ill buy it off oyu for the price of all the parts+parts+shipping? or give ma a list of parts you used and how/where u used them?
mattrox1221 3 years ago
what gearing were u using?
mattrox1221 3 years ago
if you put a traxxas vxl system in a regular stock e revo do you think it will work?
mattrox1221 3 years ago
As stated before, just gear it WAY down. 35mph is about the max you want to run it, w/o an early death. I would still monitor temps.
stumblinh 3 years ago
is that car you were runnig lighter than a stock revo waith a single cell? and b how much?... and if i went with the vxl in a stock e revo do you think it will pop wheelies?
mattrox1221 3 years ago
is this just the emaxx transmission locked in 2nd?
shittybill93 3 years ago
The 3905 tranny is a 2nd only transmission no need to lock and built brushless ready. PS it is the same tranny that is in the new e-revo.
stumblinh 3 years ago
If i put 1 vxl in my new emaxx would the speed be any faster than the titans?
9DevilDog3 3 years ago
well i race mine but on 2s lipo with mamba esc and it runs fine it was 16/68 but moved up to 18/68
tomav1987 3 years ago
on one velinion motor did u ever race it and what was ur gearing
tomav1987 3 years ago
Don't try to race with this setup... if you do gear it LOW and I mean LOW.
stumblinh 3 years ago
i was wondering why you dont recommend racing with this? i run almost 50mph with my stampede vxl on 8 cell 4200mah pack those 40mph wheels suck cause then she walks and baam cartwheel galore lol
merritts28 3 years ago
The erevo or even emaxx is 10-12 or more lbs with batteries.. that is the difference :)
stumblinh 3 years ago
does that make this motor no good for racing? in the e-revo
merritts28 3 years ago
Heat will get the best of you pushing it in a real race... that is all eventually the heat will start demagnetizing the rotor and she will be lost.. trust me, I did it ;P I would pick up a Neu 1515 motor (2.5d is an awesome racing motor! The 1y and 1.5d are also solid choices.
stumblinh 3 years ago
The max u can do is 36 miles or it will overheat lol. Its called a fan. U can easily do constant 70 mile+ as long as u have a good fan. Cus wats the point of doing slower speed than a stock E-revo does. I have a stock 1,and I do like 40 miles.
Kevster012 3 years ago
Sorry boss, a stock titan 550 setup running at 40 will be dead FAST.. LOL. The point wasn't anything other than it would work if it had to. I run a Neu 1515 1.5d capable of 50mph on a 4s lipo config, over 60 w/ 6s :P Brushless = no burnt titans as well, those titans die fast where the brushless set to the right speed the little single velineon would get you the same top speed, and last a VERY long time.
stumblinh 3 years ago
what batterie!!!?!?
Brothers221 3 years ago
This was with a Maxamps 3s2p 8000mAH lipo. Even with this config the most you can do safely with the velineon motor is about 36mph, any more and you'll be overheating constantly.
stumblinh 3 years ago
how much that batterie cost
Brothers221 3 years ago
if i use one vxl motor in my e-revo with one 5000mah 3-cell 20c lipo and gear it low and bash around my backyard do you think it will still get hot
jarbear001 3 years ago
Just keep it geared around 35mph and it will hold up fine.
May want to snag a Medusa 70mm 2200kv motor when they release in a couple weeks.. running on 4s lipo it will be amazing... and they are only 120 direct. Castle is about to drop their v3 MMM that is ready to go or you could always use a MM w/ a BEC to run the 4s config.
stumblinh 3 years ago
ok thanx but untill then i will jus run the vxl and do you possibly know the stock pinion and spur of the new e-revo or if you dont what gears should i run to keep it cool like how many tooth spur and pinion do you suggest
jarbear001 3 years ago
Maxamps 3s2p 8000mah Lipo.
stumblinh 3 years ago
Just got an Emaxx (older one) with Feigao 9xl and BK ESC. Definitely going to buy an E-revo and swap the stuff into one. The Emaxx gets the E-Revo gear or I'll just sell it LOL. Great vid and nice neighborhood. :)
CommanderB9488 3 years ago
emaxx? he said its a revo
Kevster012 3 years ago
I still think that is fast for the emaxx with a motor that really ain't ment for it.
sumitkid123 3 years ago
whats your gearing ?
nitrors4pr 3 years ago
19/68 at the time.. I'm running a Neu 1515 1.5d, I wouldn't suggest a velineon for much more than 35mph, otherwise it will be way too hot :)
stumblinh 3 years ago
a dont think toys can go over 50mph!
nitros sound better and are fun, but they will never have the torque of a good brushless system! proud owner of a rusty vxl on 3s lipo!
999benhonda 3 years ago
Check my recent videos, my Neu 1515 1.5d on 4s does about 50, on 6s with out changing gearing I was at 62 gps'ed. If I drop the spur to 54t I'll be at 70mph w/ my erevo :)
stumblinh 3 years ago
sound of the electric motor is awful,it sounds like toy, nitro is a nitro :P
kozaczi 3 years ago
You should see it with my Neu 1515 1.5d, on 4s there is no nitro that can keep up with me let alone when I strap in 6s! LOL this toy ownz the nitro, but at least you have the nitro sounds and nitro mess to clean up :)
stumblinh 3 years ago
HAHAH
i love it when you say OHH DAMN MAYBE A LITTLE TORGUE
teamlawless17 3 years ago
does the e-maxx trany go right in to the revo?
fromdaboz707 3 years ago
It takes a bit of dremmel work and a small brace to make it 100% solid. Took a few hours at most. Over on traxxas's forum if you search for "erevo revolt" you will see my entire conversion process.
stumblinh 3 years ago
i am very interested in getting one how much did it cost?
jrod8201978 4 years ago
450
lthummina 3 years ago
i set up my revo with a single velineon and it's amazing. i tried it with a mamba max with the 5700kv motor and it got waaay to hot waaay to fast. (both setups with 11.1v lipos). Velineon's the way to go.
sugarpillkiller 4 years ago
what kind of temps did you see with this? i know in my maxx geared for the speeds i got it was HOT, but geared for the speeds in the video, what kind of temps did you see?
motoSX125 4 years ago
with a vxl system in my e-maxx i broke 45 with it. but it was hot and didnt get much run time. and a mamba max, feigao, and twin 2s lipo packs would cos ta lot mroe than a vxl on 3s. but i wouldnt recomend the vxl. its not the best thing for a heavy revo...
motoSX125 4 years ago
I would only use this motor geared for 35mph, it will be pretty torquey and it will last for a good amount of time. Yes, stick with a 3s lipo config for max voltage and lowest temps. It wouldn't cost much more for a better setup though, a mamba max esc with a castle creations external BEC on a Fiegao 8XL and two 2s lipo's (4s in series) would be a MCUH better config and get you around 45mph.
stumblinh 4 years ago
If you use a single VXL system with a 8.4v NIHM battery will you still have a quick yet reliable truck? What kind of gearing do u use too? Temps?
moparmaxx26 3 years ago
wooooooow man is that with lipo?
is it faster then the nitro?
i'm thinking of an e-revo either but don't want to spend much on a high end brushless system.
so a velineon would be perfect!
tibovdb 4 years ago
thats wot i wont my t-maxx to be like
RCbasher07 4 years ago