RA TECH WE NPAS

[Canuck2503]

how do you adjust the Fps?

[gogojejej]

would this work with a we tech pdw, and will it bring the fps under 350?

[baker861120]

My RA-Tech open bolt SCAR has a plastic nozzle over the NPAS. So how do i change the FPS? Cause when I use the little tool to screw the NPAS there are no valve opening/closing and I can screw for infinity without it stopping.

How do I change the fps?

[baker861120]

My RA-Tech open bolt SCAR has a plastic nozzle over the NPAS. So how do i change the FPS? Cause when I use the little tool to screw the NPAS there are no valve opening/closing and I can screw for infinity without it stopping.

How do I change the fps?

[DeathMark22]

Setting up an M14 EBR GGBR by WE with NPAS kit should be safe right? I mean has there ever been any issues arising later on from the modification of the nozzle.

[thegeneral123]

Could you please do a video of the NPAS system for the WE G39 please?

[snipingownsu]

Is there a video on how to install this into the WE m4A1?

[PILUPACKSXXX]

What is the MAX,MAX  fps ?

[driftinsti]

Do you guys make an all steel trigger set for the WE SCAR?

[snipingownsu]

a good tutorial, but still a little confused on how to adjust the FPS

[bachelbel]

what did you do between 1:05 to 1:15? Do i have to cut the original nozzle and than keep the black part only?

[USMCole]

Sweet then I'll get one right away. By the way, I think you guys should make a 3 round burst kit for the WE. I'd buy one

[USMCole]

Could this drop the velocity of the we m16 under 380?

[ratech5915]

yes the kit can adjust the fps under 380.

[xXgoROTinAsack89Xx]

When you unscrewed the valve and put some lock-tite on the rod, that got me thinking.

Couldn't you just unscrew the SCAR's original valve and then put on the NPAS valve?

[COOLDOGMATIC]

Is the compatible with the WE m4

[svetloste]

they make a different one for the M4 (the rear clip for the SCAR isnt needed for the M4)

[ArexAirsoft]

@COOLDOGMATIC not this one, but there is one available for the WE M4 too, its a slightly different shape though

[svetloste]

Will buy one ASAP need it to use my SCAR indoors!

[fury9800]

Is there anyone in the US selling this part?

[Sbairsoft]

asgi, evike

[fury9800]

Yeah they finally got it at Evike. I got it recently and installed it. YAAAAAAAY!!! Under 400 FPS FTW

[Hoot513]

as i understand stock WE Scars have a habit of blowing out screws, pins and stocks due to the high gas pressure. i am wondering if this NPAS kit will bring the pressure down to a level that the gun can handle and solve these problems? thanks!

[vladimirtmb]

nice work, guys

will get one asap

offtop:

I still hope though that sometime airsoft manufactures will switch to electronic controlled valves that are actually cost the same

[charlestheneedler]

I agree with dasabeke. Its always nice to have a spare parts, and it will be more easier to change fps if you have two sets of NPAS, because setting the right fps everytime seems a bit more time consuming because to have to pull out the bolt carrier every time you need to adjust the fps. And I don't see any indicator on how much turn of the nozzle you have to make to get the right fps the user want. But its a good innovation none the less, keep up the good work guys.

[dasabeke]

Why dont you guys sell the whole set of nozzle (complete) instead of cutting original rod and use the old ring ? Some ppl still want to keep original parts in case anything !!!!!!!!!!!

[sideways101]

You can still save the old rod, not needing to cut it. From the original part, just loosen the nozzle part from the rod, then you can freely pully it out undamaged, and saved. The rod will pull out from the back part of the cylinder where he took out the E-clip.

[dasabeke]

what is blue liquid that you put on the rod before the nozzle?

[ratech5915]

thread locker

[dasabeke]

where can i buy thread locker?

[kittenclaws]

any decent hardware store, plumbing section.

[bquizzle88]

You can just google it. The brand Loctite makes some and i assume it will probably be available at your local hardware store.

[jose6is6EMO]

@ratech5915 do i need to put thread locker on it or can i just screw it on?

[plecofish]

wow, what kind of velvet hands...

broke original parts, assembly items with

THOR hammer technique.... fantastic

[xXgoROTinAsack89Xx]

what about for the WE M4?

[acid3x]

can't wait to get one of these for my SCAR! Gerat work!

[ARX7ARBALESTZ7]

i still don't get how to adjust the fps, what did you use to turn it and stuff? or better yet just explain please

[kittenclaws]

They include a tool with directions, but you're essentially widdenning or tightening a valve that restricts gas flow.

[MudHut67]

awesome