h t t p : / / w w w.megaupload . c o m / ? d = X O W 8 V K G Q
Hey I'd built one of these 14 years ago, I'd used the original Stanley Meyer information packs that he'd used in Auckland New Zealand which included the original WFC Software I took a picture of it in the Mega link above. Basically alligns frequency to cell capacitence
My cell generated about 3 Litres of gas every minute. I found that I'd acheived the best stoichiometric combustion using combined gas than using hydrogen alone.
what is all that brown shit on the top of the water?why does the water look like its thick and viscous?does this process use an electrolye?which 1?i never read any of stan meyer material can you post a link to some good sources?
waterforfuel is such a scumbag.... He claims hes "replicated" Stan Meyer but his shitty setup draws lots of power and produce little HHO... As long as he can live out of other people donations he will run this scam... His car always brakes down, he needs to pay for this he needs to pay for that... always begs for donations... He is trying to FORCE match impedance with 4 microwave caps and some 10ohm max inductor... WHAT A JOKE MAN! Negative reviews are always deleted from his blog!!!!!!
Stan Meyer's book says to make tube cells 3 inches tall, and Stan Meyer NEVER conditioned his tube cells. And Stan Meyer used a hig voltage alternator (VIC, says it right there in his book). Stop taking advise and start readinhg the directions yourself dude.
Stan reinvented the steam engine, HHO does not create the explosion of gasoline but does burn way hotter. thus his injectors turned a portion of water to HHO the rest was turned to steam through out the power stroke.
I could be wrong but thats what i am seeing. and i would much rather use that than gasoline any day the torque and horse power that could be created with that idea is tremendous.
read his work? I'VE REPLICATED HIS WORK. Where is your replication? I'm almost finished with an injector. Where is your injector? Steam doesn't ignite and Stan never says it does.
actually yes steam will. when hot enough steam will separate and become it components,again. HHO make heat not explosion power. the only explosion you get is a small one that is hot enough to produce steam.
and then you may drive your watered powered car to my house and prove it.
Actually you still didn't mention a page number or any refferences. Stop pissing me off,check out my videos, and READ STAN MEYER'S MATERIAL. I'll be at your house soon to run you over.
show me where he is putting air through the injector? cause if you put air in the water injection system you will only accomplish vapor locking the water pump.
You think you know more than I do? That is funny. I have more info than you do. And if you would have check my profile you'd have seen my big intake air ionizer. And there is irn being mixed with the water injectors of Stan's...everyone knows that because we have all the info. LOts of diagrams of air, water with HHO, and exhaust gas. It is on page 107 of the book. But you haven't read the book...that is what this is all about remember, you don't knwo what you're talking about.
Whatever dude. You're all talk and no proof. You didn't even know the page number in the book that stated you were wrong. You've been wrong since you've opened your mouth and you can't prove otherwise. On the other hand I got more videos and proof than you. Make an injector, make a video, and prove me wrong.
The injectors were never finished. What did the dune buggy run on before the injectors? Magic dust? Steam in a can? It ran on HHO you tard. I'm ignoring you now.
the whole idea behind it is steam. yeah if you think you can create 100,000 LPM to run that engine i know you weren't understanding it.even the damn bug has no AIR going through the injector. to ionize enough water you would need at least a 3 gigawatt laser. He did an amazing amount of misleading to keep what he did hidden. and yes if steam is hot enough it will separate and ignite again.
Good Job putting it together. I did not see any gas lines for leading the gas to where you want it!
I surly hope you are not just venting it into your livingroom space?
Take care and remember that Hydrogen is twice as light as helium (Used for Baloons) and will collect in pockets under your sealing where just one spark (Opening your light) could create a massive explosion.
Anyway nice replication and good luck on your advance in production!
i think the idea is to resonate the water with a special frequenct to make splitting easier you need to elongate the water molecule so its at its maximum just ready to be released then pulse it thats what i recogn anyway the question is what is that frequency
and how do you incorparate that into the electronics
You will see a growth in alternative energy that will spring from the general public from the grass roots of our society. I believe you will see a black market in energy.
You may even see some forms forbidden as the corporation try to maintain control.
It may even be described as an energy civil war.
The rising cost will make many people think out side the box and try things that are not even considered possible.
This has been flagged as spam show
h t t p : / / w w w.megaupload . c o m / ? d = X O W 8 V K G Q
Hey I'd built one of these 14 years ago, I'd used the original Stanley Meyer information packs that he'd used in Auckland New Zealand which included the original WFC Software I took a picture of it in the Mega link above. Basically alligns frequency to cell capacitence
My cell generated about 3 Litres of gas every minute. I found that I'd acheived the best stoichiometric combustion using combined gas than using hydrogen alone.
ilav1m8y 9 months ago
I want information, information How many milli amps as hydrogen information information
Svetovidijak 11 months ago
what is all that brown shit on the top of the water?why does the water look like its thick and viscous?does this process use an electrolye?which 1?i never read any of stan meyer material can you post a link to some good sources?
bulletproof2353 1 year ago
waterforfuel is such a scumbag.... He claims hes "replicated" Stan Meyer but his shitty setup draws lots of power and produce little HHO... As long as he can live out of other people donations he will run this scam... His car always brakes down, he needs to pay for this he needs to pay for that... always begs for donations... He is trying to FORCE match impedance with 4 microwave caps and some 10ohm max inductor... WHAT A JOKE MAN! Negative reviews are always deleted from his blog!!!!!!
nadinka007 1 year ago 8
@nadinka007
you are a nice person keep up the good work LOL
toranarod 1 year ago
@nadinka007 good comment
irondmax 10 months ago
cool
irondmax 1 year ago
very neet !!!
vox1philippines 1 year ago
get a mike can't hear you !!!!
meesphht 2 years ago
Stan Meyer's book says to make tube cells 3 inches tall, and Stan Meyer NEVER conditioned his tube cells. And Stan Meyer used a hig voltage alternator (VIC, says it right there in his book). Stop taking advise and start readinhg the directions yourself dude.
waterforfuel 2 years ago
exactly. people on the internet say to use high amps and electrolyte, which is super inefficient! high voltage all the way! 20kV if you can lol...
harryfodder 2 years ago
I didn't even know he had a book
nebulareclipse 2 years ago
@waterforfuel
Stan reinvented the steam engine, HHO does not create the explosion of gasoline but does burn way hotter. thus his injectors turned a portion of water to HHO the rest was turned to steam through out the power stroke.
I could be wrong but thats what i am seeing. and i would much rather use that than gasoline any day the torque and horse power that could be created with that idea is tremendous.
juggernautxtr 2 years ago
@juggernautxtr ...yea, you're wrong.
waterforfuel 2 years ago
actually you need to read the his work thoughly.if you look at the injectors he is not converting all the water to HHO.
steam when hot enough will also ignite.
juggernautxtr 2 years ago
read his work? I'VE REPLICATED HIS WORK. Where is your replication? I'm almost finished with an injector. Where is your injector? Steam doesn't ignite and Stan never says it does.
waterforfuel 2 years ago
actually yes steam will. when hot enough steam will separate and become it components,again. HHO make heat not explosion power. the only explosion you get is a small one that is hot enough to produce steam.
and then you may drive your watered powered car to my house and prove it.
juggernautxtr 2 years ago
Actually you still didn't mention a page number or any refferences. Stop pissing me off,check out my videos, and READ STAN MEYER'S MATERIAL. I'll be at your house soon to run you over.
waterforfuel 2 years ago
give me your email and i will send the whole god damn thing.
juggernautxtr 2 years ago
next you'll be telling me you built a laser strong enough to ionize air fast enough for the engine to consume.
juggernautxtr 2 years ago
show me where he is putting air through the injector? cause if you put air in the water injection system you will only accomplish vapor locking the water pump.
juggernautxtr 2 years ago
@waterforfuel where can you read stan's work?
drumstick9000 1 year ago
@juggernautxtr
You think you know more than I do? That is funny. I have more info than you do. And if you would have check my profile you'd have seen my big intake air ionizer. And there is irn being mixed with the water injectors of Stan's...everyone knows that because we have all the info. LOts of diagrams of air, water with HHO, and exhaust gas. It is on page 107 of the book. But you haven't read the book...that is what this is all about remember, you don't knwo what you're talking about.
waterforfuel 2 years ago
like i said
8078 KB of space took up on my computer.
just patents. sorry but if you actually look at the injectors he is injecting water into the cylinder.
if you pd attention thermal explosive energy(heat)
creating steam in the cylinder.and yes steam driven engine.
juggernautxtr 2 years ago
@juggernautxtr
Whatever dude. You're all talk and no proof. You didn't even know the page number in the book that stated you were wrong. You've been wrong since you've opened your mouth and you can't prove otherwise. On the other hand I got more videos and proof than you. Make an injector, make a video, and prove me wrong.
The injectors were never finished. What did the dune buggy run on before the injectors? Magic dust? Steam in a can? It ran on HHO you tard. I'm ignoring you now.
waterforfuel 2 years ago
what ever dud just proves my point.
the whole idea behind it is steam. yeah if you think you can create 100,000 LPM to run that engine i know you weren't understanding it.even the damn bug has no AIR going through the injector. to ionize enough water you would need at least a 3 gigawatt laser. He did an amazing amount of misleading to keep what he did hidden. and yes if steam is hot enough it will separate and ignite again.
juggernautxtr 2 years ago
How many amps r u drawing? What blog/people helped with the V.I.C?
tommygunn628 2 years ago
it doesnt look like its working right, the original using the original parts and accesories made bubbles 1 - 11/2 inches above the stainless tubes.
just a few more tweaks and youre there ;)
bikr1975 3 years ago
Please, can you tell us what the ltrs per minute is??? Thanks!
wslybe 3 years ago 2
Good Job putting it together. I did not see any gas lines for leading the gas to where you want it!
I surly hope you are not just venting it into your livingroom space?
Take care and remember that Hydrogen is twice as light as helium (Used for Baloons) and will collect in pockets under your sealing where just one spark (Opening your light) could create a massive explosion.
Anyway nice replication and good luck on your advance in production!
HHOvaageng 3 years ago
good work but could you show us anice flame comin out that device
3abdellatiff74 3 years ago
have you taken any measurement?
liters per minute?
natony0please 3 years ago
can you tell me where I can get hydrogen fuel cells
super8471 3 years ago
are you talking about Hydrogen or water fuel
cells.
toranarod 3 years ago
i think the idea is to resonate the water with a special frequenct to make splitting easier you need to elongate the water molecule so its at its maximum just ready to be released then pulse it thats what i recogn anyway the question is what is that frequency
and how do you incorparate that into the electronics
theoneagain 3 years ago
plz take a look at my vid labeled
D Flip Flop output rotation HHO
jeffnicq 3 years ago
You will see a growth in alternative energy that will spring from the general public from the grass roots of our society. I believe you will see a black market in energy.
You may even see some forms forbidden as the corporation try to maintain control.
It may even be described as an energy civil war.
The rising cost will make many people think out side the box and try things that are not even considered possible.
toranarod 4 years ago 2
this is exactly what ive been looking for. i also live in austrailia. would you consider building and selling me one ?
Popstarlive2005 4 years ago
yes why not. look at your private messages.
toranarod 4 years ago
1.5 mm plastic spacers, chopped up peace of
cable tie spaced 120 degrees apart.
But the bottom is drilled and fitted to PVC
plastic storm water pluming pipe end caps.
toranarod 4 years ago
What do you use so the tubes inside each other show they don't touch??
bigfrog12069 4 years ago
Can you tell me what that metal strap around your tube set up is?
Does that strap connect to the positive lead? Is it available online to buy?
Jopipang 4 years ago
It is a Stainless steal hose clamp.
and is the positive connection.
it hold the top of the tubes together and provides a good connection.
toranarod 4 years ago
try using the back EMF from your bedini as a pulse to the cell
m3sca1 4 years ago