Knowledge is power! You have to know bending principles to use any tool. The best and easiest to understand workbook which can be used by anyone to become an accomplished conduit, tube or pipe bender can be found on a youtube website at /t04041951
its as accurate as the die. How could it not be parallel, its wrapping around a common axis with both ends supported. offset can be done by moving the brass slide up and down, but not much.
@codalisa007 we have one of these machines at the shop i work at. it really is nice to work with if you have your deflection angle set on a test piece before bending work pieces. doesn't nessarily have to be parallel with the leg, at the controll you input your bend angle and deflection angle and push a button. awesome machine to use
overpriced machinery. mine has a 7" grinder mounted underneath for the prime mover! the end of the armature shaft snapped off one day and ercolina wanted 700+ bucks just for a armature! I fixed it myself.
to:boganindustries. do about 50-60 bends with S/S tubing or pipe and see what happens to your illustrious brass block.
they never show these machines bending stainless. we bend stainless and one project will just about kill that brass slider. that's what I don't like about these machines. For what they cost they should furnish a hard steel slider block and a
This has been flagged as spam show
Knowledge is power! You have to know bending principles to use any tool. The best and easiest to understand workbook which can be used by anyone to become an accomplished conduit, tube or pipe bender can be found on a youtube website at /t04041951
Todd04041951 3 weeks ago
how can find supplier of this machine , I,m in Brazil
paulogeronimoqueiroz 1 month ago
its as accurate as the die. How could it not be parallel, its wrapping around a common axis with both ends supported. offset can be done by moving the brass slide up and down, but not much.
68pishta68 4 months ago
Didn't look very accurate to me. I noticed he never checked the tube to see if it was parallel with the other leg (i.e. 180 degrees)
codalisa007 7 months ago
@codalisa007 I don't think they were going for 180 degrees.
junekentucky 7 months ago
@codalisa007 we have one of these machines at the shop i work at. it really is nice to work with if you have your deflection angle set on a test piece before bending work pieces. doesn't nessarily have to be parallel with the leg, at the controll you input your bend angle and deflection angle and push a button. awesome machine to use
radioactivepenguin23 6 months ago
@codalisa007 its as accurate as the operator makes it.
Duckyistrippin 4 months ago
Do you send the music too ?
michaelovitch 9 months ago
SHEESH THIS MUST COST A PRETTY PENNY OR 2
blueange1s 11 months ago
overpriced machinery. mine has a 7" grinder mounted underneath for the prime mover! the end of the armature shaft snapped off one day and ercolina wanted 700+ bucks just for a armature! I fixed it myself.
to:boganindustries. do about 50-60 bends with S/S tubing or pipe and see what happens to your illustrious brass block.
MAS5270 11 months ago
they never show these machines bending stainless. we bend stainless and one project will just about kill that brass slider. that's what I don't like about these machines. For what they cost they should furnish a hard steel slider block and a
non metalic block for non ferrous metals.
MAS5270 1 year ago
@MAS5270 Yeh look at all the brass coming off sheesh
boganindustries 1 year ago
hola, estaria interesado en adquirir un curbadora, me podrias dar informacion
sproman5858 1 year ago
Superman can't do that?
Thetruthishere11 1 year ago
how much for this unit
dbi1036 2 years ago
how much flattening? Will it bend 2 1/2" schedule 80 steam pipe?
Robkat3751 2 years ago
What are you bending? Handrails? You just KNOW someone tries to use this for electrical!
SaviourSole 2 years ago
Nice a wiper die as well
bender39611 2 years ago
super
thomas26034 3 years ago
very nice machine, how to contact your company?
caiquemacedo 3 years ago