i submit that this would work even without the wd40 but importantly i bet there is still current leakage into that water which shows that the wd40 isnt doing shit
@MrTheklotter im not going to do this, but the producer of this vid who is obviously ok with doing this to start with could re-run the test and do a current leakage reading on the water itself. If there is current leakage then the wd40 might be mitigating the leakage but isnt water proof.
The new version of WD-40 has Alcohol in it.. it will not seal water anymore, nor will act as a rust breaker anymore with good effect. But it IS a great parts cleaner.
@thinkpad411 the damage would be due to corrosion mostly, but water by itself is a dielectric, only when impurities are added its electrical properties begin to change. You'll see good examples with electronics, say a person drops a digital camera in a puddle of rain water, the camera may work fine for a period of time but eventually begin to fail, upon opening up the camera to determine the point of failure, corrosion should be found. Get a DMM and experiment with different kinds of water.
@teslaresearch Ah i see. I'm studying as an automotive technician at college right now (1st year) and we're learning the fundamentals of electricity and circuits. I'm understanding the properties of conductors quite well. I never have tooken a DMM to water but would it show an actual reading? Would it be proportional to the volume of water measured?
You all do realise that water by itself is really a very poor conductor of electricity right?? There need to be significant numbers of ions disolved in the water for it to conduct to any real extent. Hence, why people can get electrocuted through water.. They touch the water and all of the ions that are in their sweat, on their skin, etc dissolve in the water and allow for conductivity.
Dissolve something that will dissociate into ions, like salt, and this will be more believable.
I think what he is trying to show is that since WD40 is a lubricant ( oil ) and watter wont mix so the water has no contact with the terminals of the holder because it was sprayed with oil (WD40) cuz again water did not have contact with the terminals because there was oil on them
yes because un distilled water has ions which is what lets electricity flow across the terminals look up more light bulbs in water and yould find a experiment showing the test
@yittymitty11 Ummm, dude? It's not about the ions, the amount of electrolyte in the water determines how much electricity can cross it, and distilled water has no electrolytes which means that electricity can't cross through it to ionize the molecules..
wait ..WHAT????? Damn dude I need to go back to school!!.....
piersremus 2 months ago
In this case, you will warming...boiling the water and water has resistance too, not immediately short-circuit, that "wd"
actually doesn't save anything, are you ready to dip your fingers in the water to? - Hope not!
advertising trick... :/
NXSeeMartin 2 months ago
@NXSeeMartin
If its distilled water, its a perfect insulator, its the impurities that make it conduct.
togethia 2 months ago
This has been flagged as spam show
GREAT VIDEO
lmogden1 2 months ago
you didnt put your finger in there?
CreeDLiaM 3 months ago
i want to see it without WD40
vleeskaak 3 months ago 2
does anyone know what WD-40 stands for ?
Water Dissipater formula # 40
MrBigtower 3 months ago
@MrBigtower
WD 40 = Water Dispersant formula 40 from the 40 version before it met NASA spec.
togethia 2 months ago
@togethia the 40 is the weight of the oil.... what the hell are you talking about
Runbleeding 2 months ago
@Runbleeding WD-40 literally stands for Water Displacement, 40th attempt. What the fuck are YOU talking about?!
NAMkiller 2 months ago
@Runbleeding
40 is the 40th Recipe for the formula, if it were the weight of the oil WD40 would be a lot thicker than it is.
Check out the FAQ on WD40(dot)com and you will indeed discover that we are correct.
togethia 2 months ago
@Runbleeding
You are simply wrong...
peterfarrow 2 months ago
for this test to really prove anything, salt needs to be added to the water as water alone in a pure state isn't conductive.
ki4hou 3 months ago
UNBELIEVABLE!!!
yaris4fun 3 months ago
i submit that this would work even without the wd40 but importantly i bet there is still current leakage into that water which shows that the wd40 isnt doing shit
lynel1985 4 months ago 4
@lynel1985 do it and post a vidoe then?
MrTheklotter 3 months ago
@MrTheklotter im not going to do this, but the producer of this vid who is obviously ok with doing this to start with could re-run the test and do a current leakage reading on the water itself. If there is current leakage then the wd40 might be mitigating the leakage but isnt water proof.
lynel1985 3 months ago
Holy shit, thats gotta be one of the most dangerous things I've seen done for a while... Dare you to dip your hands in lol
NorkiddExo 4 months ago
wd stands for water displacment
theman5419 4 months ago
The new version of WD-40 has Alcohol in it.. it will not seal water anymore, nor will act as a rust breaker anymore with good effect. But it IS a great parts cleaner.
KeiYuuki2011 4 months ago
@KeiYuuki2011 Yeah, the old stuff was great. It had fish oil in it, too, so some recommended it for fishing line lubrication.
stopglobalswarming 2 months ago
grease is better. WD- 40 will wash away.
poiiihy 4 months ago
Now that I have a can of WD-40 as a redneck wasp killer. :)
JerryGiesler09 4 months ago
Agua destilada? xD
trefhi 4 months ago
i use it when it has a bad connection , just spray it and it works :)
VPindustries 5 months ago
is there anything wd40 cant do
lilgampla 5 months ago
So ummm what's this supposed to prove
MrDixiepride1234 5 months ago
@MrDixiepride1234 for you....uummm nothing....
Shaban85 5 months ago
you made your point .... BUT it was a pretty DUMB way to prove it
dasalekhya 6 months ago
now some 77yer kid put a lightbulb into water and dies.THATS UR FAULT!
MrZombi98 6 months ago
Tap water by itself is not conductive, but add a little salt to it and it does become conductive........dare ya to try this with salt water.....lol
teslaresearch 7 months ago
@teslaresearch Really...? Isn't all water conductive to the point where it will damage electrical circuits?
thinkpad411 5 months ago
@thinkpad411 the damage would be due to corrosion mostly, but water by itself is a dielectric, only when impurities are added its electrical properties begin to change. You'll see good examples with electronics, say a person drops a digital camera in a puddle of rain water, the camera may work fine for a period of time but eventually begin to fail, upon opening up the camera to determine the point of failure, corrosion should be found. Get a DMM and experiment with different kinds of water.
teslaresearch 5 months ago
@teslaresearch Ah i see. I'm studying as an automotive technician at college right now (1st year) and we're learning the fundamentals of electricity and circuits. I'm understanding the properties of conductors quite well. I never have tooken a DMM to water but would it show an actual reading? Would it be proportional to the volume of water measured?
thinkpad411 5 months ago
The guys at Q20 actually hold the bulb under the water!!!
Q20Oil 7 months ago
i wouldnt touch the waer
sillu129 7 months ago
WD40 stands for "water displacement, 40th attempt" no joke invented in 1953 the guy hit it lucky 40th attempt lol
tbrowniscool 7 months ago
@tbrowniscool Surprising but true.
toad773 7 months ago
I'd like to see what happens in contaminated (as in normal tap-) water.
aphoxema 7 months ago
WD stands for water displacement!
grapeknutz 7 months ago
Hey! I Watched! That Is Unbelieved Thing What I Didn't Know Before! Thanks For This! Feels By assa!
DirtyAssa 8 months ago
Put ya hand in it.
benny2980 8 months ago
is that water?
MrRoyXDwetering 8 months ago
Water is a good insulator with or without WD40, if it is distilled water... And probably is.
spinixDH 9 months ago
add warning- you are otherwise liable.
gnamp 9 months ago 2
water displacment formula number 40
firstamendright 10 months ago 3
@firstamendright water displacement formula 40th try. (WD-40)
kyletango 9 months ago
You all do realise that water by itself is really a very poor conductor of electricity right?? There need to be significant numbers of ions disolved in the water for it to conduct to any real extent. Hence, why people can get electrocuted through water.. They touch the water and all of the ions that are in their sweat, on their skin, etc dissolve in the water and allow for conductivity.
Dissolve something that will dissociate into ions, like salt, and this will be more believable.
flight110 10 months ago
WD40 is alcohol based and will repel water, but it will evaporate.... for a longer lasting solution you should use a silicon spray
TheLadyboy101 10 months ago
oh wow, hence the Water Displacing formula 40
fyrebyrd301 11 months ago
wow this is cool
GoldenKnight422 11 months ago
hahaha water is desalted
caprice2020 11 months ago
But for how long?
73831 11 months ago
that is extremely dangerous and i do highly suggest trying this.
leet413 1 year ago 7
Wah! I've never been stupid enough to try it, but now I am a true believer. Jesus apparently loves wd40, hates sin (so they tell me)
sitwosaints 1 year ago
WHAT THE FUCK are you kidding me i thought it was gonna blow up hahaha
matthewblack1322 1 year ago 36
wd 40 repelles water
goad07 1 year ago 32
@goad07 wd 40 displaces water
ChadALambert 8 months ago
@goad07 That's the point, but for some reason it's big WOW for most people.
ValutDweller 6 months ago
@goad07 indefinitely?
Allexxx96Reloaded 5 months ago
@goad07 but ca it repelle bullets as well?
ARAFELI 3 months ago
This has been flagged as spam show
good for when you need to have underwater light , but are to cheap to spring for proper housings
technosasquatch 1 year ago
good for when you need to have underwater light , but are to cheap to spring for proper housings
technosasquatch 1 year ago
that's incredible!!!!
adri2699 1 year ago
@Thetruetv hahaha ur an idiot. Wd-40 bah
quackersabc 1 year ago
What did you spray on it?
Thetrutv 1 year ago
@Thetrutv WD-40 like it said in the title
italian789456 1 year ago
oil replaces water which not shocking the bulb..WTF AM I SAYING?!?!?
htirah100 1 year ago
This has been flagged as spam show
Hey, I found some more of these videos here on this website:
m0ar [DOT] org/4765
(Replace [DOT] with . ) - Pretty cool stuff! :D
SexyAnnia18 1 year ago
WD40.. The WD stands for Water Displacement..
JasWarLea 1 year ago 2
@JasWarLea n when fire comes into play it means MUSTARD GASSSSSSSS
TheFinalFrame 1 year ago
@TheFinalFrame dude its WD not MG
AnimeMasterDavid 1 year ago
@JasWarLea water displacement,40th attempt :)
alejnaarifi 1 year ago
I think what he is trying to show is that since WD40 is a lubricant ( oil ) and watter wont mix so the water has no contact with the terminals of the holder because it was sprayed with oil (WD40) cuz again water did not have contact with the terminals because there was oil on them
pixelsblack 1 year ago
not recommended for children under 65 years of age.
theguvernmentman 2 years ago 2
@theguvernmentman haahahahahahah
motabikeboy 1 year ago
hmmmm
thashogun1 2 years ago
@thashogun1 looks like it might be distilled water
yittymitty11 2 years ago
would that matter?
thashogun1 2 years ago
yes because un distilled water has ions which is what lets electricity flow across the terminals look up more light bulbs in water and yould find a experiment showing the test
yittymitty11 2 years ago
srry *un distilled water has no ions*
yittymitty11 2 years ago
@yittymitty11 Ummm, dude? It's not about the ions, the amount of electrolyte in the water determines how much electricity can cross it, and distilled water has no electrolytes which means that electricity can't cross through it to ionize the molecules..
cappydawg 1 year ago 2
@cappydawg so why dont you stick 240 in a bucket of distilled water and stick your head in there and tell me how you feel after?
robby844 1 year ago