@monkeys1954 Completely wrong. 5L is the total displacement of the cell. The engine will only suck fuel during compression stroke. It really depends on the compression ratio but trust me, it is not 5L.
@joeshmo14760 a 4 stroke engine requires 2 rotations of the crank to aheive full cylce. Also the 5L of air you talk about is at atmosphereic pressure, or 1 bar. You will only see this at 100%throttle. All other times the engine is under vaccum, which is stretching the air, that is why for calcuations always use weights of fuel and air. You can work out with a vac gauge how much air/fuel is required to idle your vehicle coupled with some simple maths. They you can try and make enough hho
eh, do you honestly believe that you can power your car through HHO gas at a speed of 1.5lpm? i mean all you are doing is straining the alternator, which through feedback currents will seize up and in turn require more torque from the engine. There is no such thing as a 100% efficient system.
For me 1mm gap produced the best gas at 20 amps . 20 plate system with 1 pos on each side and 2 neg inthe middle with 16 neutral plates inthe center. i get 140f max heat with 27 amps HOT and 1.5lmp and gained 44% increase in my gas millage.
Allow me to put an end to the mystery. Watch this new video for ABSOLUTE proof that it is IMPOSSIBLE for HHO to increase miles per gallon. Good stuff.
Allow me to Burst your bubble. There are 1000's of Videos here that's are Proof that This tech works Allow me also to burst you bubble and go to Smack101 Website and pancera's web site. Sir your a 100% Moron.
About a year ago Smacks video said he got an 88.8 perxcent increase. More recently he now claims 6 percent. So which is it? YOU are the ultimate moron. I have seen your moronic posts all over the place. Go back to 10 th grade science class and learn something this time.
Smack Is a Jerk I admit But he NEVER claimed 88% increase He always claims his car get 22% and Even now he claims 22% .My Van get 50% Highway .Why not build it right and learn something . If you going to say it does not work Show a Video Of a CORRECTLY built One and have the PROS Do the emissions and test runs .Its PROVEN it works Guess you need to stop your Lies.
Yes he did, it even says it in the decription on this video, 88.8 percent.
watch?v=t4316Ieswtg&feature=related
His latest claim, as he has come under a lot of heat, including Radarman threating to turn him into the Federal Trade Commision for fraud, is just six percent. Watch the videos.
Why would I build one when my video clearly shows that at 3.05 LPM an HHO device produces 1.322 MJ of energy per hour but robs 1.8 MJ of energy from the emgine to produce it? Where have I lied? You will NOT be able to point to even one lie.
LOL all my crap is sitting around my basement too...funny how many manifestations our little creations go through til we decide for ourselves what's best....I'm currently leaning toward smaller disposable units....now where's that home depot gift card....
I bought some plans from hho-hybrid . com $19.95 they seem simple but I think there is more going on than we know... haven't built unit yet but getting it together slowly!!
nice, seeing the cell installed under your hood made me realize my cell design would not fit in mine with out major location changes, so im switching from the cylinder to the box design, i want to get the most plates for 1/2 my pay check or more. Also im doing this for everyday use, have you ran into any problems, i've noticed your using a bubbler to prevent a back flash from reaching the cell, what other precautions have you taken?
old school wet cells. fun
b101aa2 9 months ago
This has been flagged as spam show
hello, you have to send the detailed design for my email, so I hope to do Brazil and a generator for use in my car.
altairdesouza@gmail.com
altairdesouza 10 months ago
something to think about. a 5.0l engine sucks in 5.0l of fuel air mix each revolution if i am not mistaken. maybe i am wrong.
monkeys1954 1 year ago
@monkeys1954 Completely wrong. 5L is the total displacement of the cell. The engine will only suck fuel during compression stroke. It really depends on the compression ratio but trust me, it is not 5L.
joeshmo14760 8 months ago
@joeshmo14760 a 4 stroke engine requires 2 rotations of the crank to aheive full cylce. Also the 5L of air you talk about is at atmosphereic pressure, or 1 bar. You will only see this at 100%throttle. All other times the engine is under vaccum, which is stretching the air, that is why for calcuations always use weights of fuel and air. You can work out with a vac gauge how much air/fuel is required to idle your vehicle coupled with some simple maths. They you can try and make enough hho
lynel1985 3 months ago
The Idea of running HHo whit lye
and 100A is not very good not practical
Try this 10A 25lit per min 110V Ac Honly Water no QUIMICALS
1miltond 1 year ago
eh, do you honestly believe that you can power your car through HHO gas at a speed of 1.5lpm? i mean all you are doing is straining the alternator, which through feedback currents will seize up and in turn require more torque from the engine. There is no such thing as a 100% efficient system.
erjohnson227 2 years ago
sad...
euchanels 2 years ago
For me 1mm gap produced the best gas at 20 amps . 20 plate system with 1 pos on each side and 2 neg inthe middle with 16 neutral plates inthe center. i get 140f max heat with 27 amps HOT and 1.5lmp and gained 44% increase in my gas millage.
Vistal1 3 years ago
This has been flagged as spam show
Allow me to put an end to the mystery. Watch this new video for ABSOLUTE proof that it is IMPOSSIBLE for HHO to increase miles per gallon. Good stuff.
watch?v=5G9DAmt_jLk
EnergySupply2008 2 years ago
Allow me to Burst your bubble. There are 1000's of Videos here that's are Proof that This tech works Allow me also to burst you bubble and go to Smack101 Website and pancera's web site. Sir your a 100% Moron.
Vistal1 2 years ago
About a year ago Smacks video said he got an 88.8 perxcent increase. More recently he now claims 6 percent. So which is it? YOU are the ultimate moron. I have seen your moronic posts all over the place. Go back to 10 th grade science class and learn something this time.
EnergySupply2008 2 years ago
Smack Is a Jerk I admit But he NEVER claimed 88% increase He always claims his car get 22% and Even now he claims 22% .My Van get 50% Highway .Why not build it right and learn something . If you going to say it does not work Show a Video Of a CORRECTLY built One and have the PROS Do the emissions and test runs .Its PROVEN it works Guess you need to stop your Lies.
Vistal1 2 years ago
Yes he did, it even says it in the decription on this video, 88.8 percent.
watch?v=t4316Ieswtg&feature=related
His latest claim, as he has come under a lot of heat, including Radarman threating to turn him into the Federal Trade Commision for fraud, is just six percent. Watch the videos.
EnergySupply2008 2 years ago
Why would I build one when my video clearly shows that at 3.05 LPM an HHO device produces 1.322 MJ of energy per hour but robs 1.8 MJ of energy from the emgine to produce it? Where have I lied? You will NOT be able to point to even one lie.
EnergySupply2008 2 years ago
I love it when people waste good money on PLans?? When there are to many Free how tos and some very very good ones. Like smack for 1.
Vistal1 3 years ago
LOL all my crap is sitting around my basement too...funny how many manifestations our little creations go through til we decide for ourselves what's best....I'm currently leaning toward smaller disposable units....now where's that home depot gift card....
pipinki 3 years ago
I bought some plans from hho-hybrid . com $19.95 they seem simple but I think there is more going on than we know... haven't built unit yet but getting it together slowly!!
blahvidblah 3 years ago
greatwork, what's the spacing on each cell. Also, how areyou sealing the terminals that's on the side of the container? any tips?
Hope to hear from you.
Keep it up!!!
bennytan777 3 years ago
Any distance down to 4 mm is good, one has to then alter the lye:water ratio to obtain the desired current
I use EPDM as a gasket and it works well
bornman88 3 years ago
This has been flagged as spam show
To discuss this, everyone go join hhoforumsdotcom to share. youtube is no place to discuss and share advantages, together we can all join forces!
TeknikL 3 years ago
support hydrogen technology and the way our future needs to be pushed, oil companies protected this information for the last 60 years.
planetblue dot net dot au
justinlwallis 3 years ago
I just posted video about the guys who sell the plans for $19.95. hho-hybrid . com or go to my videos I have one on my Dodge Stealth
amazinghybrid 3 years ago
Great work!
skagitt 4 years ago
Very good craftmanship, keep up the good work.
MrCarbJB 4 years ago
Hello there bornman88, are this plates (inox) have to be replaced after use? or how much time this can last? sorry bad english
espido 4 years ago
Yes it is 316 Stainless Steel
The long term effect is not known yet
I am about to strip my car electrode and will report back . It has been in car for two months now being used for three hours per day
bornman88 4 years ago
Do you sell this cells?
rliberato 4 years ago
I am working on two more proto types and will be tooling up once I have found the most efficient cell, then I will sell them on the net
bornman88 4 years ago
@bornman88 Hi , any developments made? Could you please give me some ideas and principles how to make the cell most efficient!
tarmogr 1 year ago
Very fascinating work. Love the song too. What's the name of it?
usp45compact 4 years ago
Artist: Antony Raijekov
Song: Photo theme: Window like
bornman88 4 years ago
Hope to see a new video soon! Are you using straight power or are you adding some sort of high frequency to obtain this terrific output?
dailytool 4 years ago
It is all explained in my other videos
bornman88 4 years ago
Very nice cell! I do not understand the structure, there are many cell stacks and are they output good volume of HHO?
wphuang2005 4 years ago
Is this 7 cells in series= ~2 volts each?
desertblbuesman 4 years ago
No, it is 8 cells
bornman88 4 years ago
nice, seeing the cell installed under your hood made me realize my cell design would not fit in mine with out major location changes, so im switching from the cylinder to the box design, i want to get the most plates for 1/2 my pay check or more. Also im doing this for everyday use, have you ran into any problems, i've noticed your using a bubbler to prevent a back flash from reaching the cell, what other precautions have you taken?
MrPlug 4 years ago
true dat, hey bornman88 what grade and gauge of plates do you use?
MrPlug 4 years ago
0.8 mm stainless steel
bornman88 4 years ago
this video make me cry!!
labidus74 4 years ago
2 times for me now! stop it!
diehard99 4 years ago
Its nice to see what your cells look like out of water, Bornman88 FTW!
MrPlug 4 years ago
GREAT VIDEO!
diehard99 4 years ago