HHO What is over unity and whats not

[alchemistsgold]

Richard, I just love your work. Your vids are clear and explained on a level that even (some of us) morons can "Grok." thanks and keep up the good work!

[hhoforvolts]

@alchemistsgold Thanks for the comments and I will my best to produce good videos in the future.

Richard

[hhoforvolts]

Come all, I will be there...many speakers and the latest devices

Tesla ExtraOrdinary Technology Conference • Albuquerque, New Mexico July 29-August 1, 2010

[hhoforvolts]

UP DATE: I want to thank Paul Oberman for a loan of a great power supply. This supply has a current limiter which allows only a certain amount of current to flow. So I held my breath and turned the unit on. The meter read 12.0 volts and 4.8 amps out. I still had 11.2 amps in the rod. Increasing the the voltage to 14.5 volts, both the current from the power supply and the rod circuit increased, but the over unity ratio stayed the same.

[T1000LTU]

@hhoforvolts

Hi there :)

It's all great stuff but 1 thing comes to mind from Rodin itself: 1 winding has power applied, another is off, then swap. It is all about dialling sequence and timing - /watch?v=K93dL65Q724&feature=r­elated

If you can figure out all that mathematics, you will probably will get desired effect.

If you make 1 more rod and try playing with it in centre of coil (where magnetic wormhole field goes out) as voltage transformer then see what output is... :)

[mikepowers420]

Richard, I hope that your up coming research is as fruitful as the past research has been.

So far, I think your work - ROCKS.

[hhoforvolts]

Thanks Mike.you will some progress in the next video.

[hhoforvolts]

Just want to thank everybody for the kind words, I really wasn't sure it would be accepted in the way I wanted it to be. In the future if this turns out not to be over unity, so what. I have got a lot of new friends and help some on there projects.

Thanks again everybody

Richard

[reeseht]

Good for you Richard!

Jim

[aquapulsefuel]

wow.you realy seem to know what your doing n respect to current draw. i am not sure if saying watts go in.....watts go out will be annoying to you given your request to watch prior video but this is how i would be metering overunity....and then in a practical way also like charging your source load. really love you clear communication inyour video. i really hope this end all good and acheive what we wish for . regards andy

[hhoforvolts]

For the given time, there's always more info to give than time will allow. In the next video I will have slides that covers the main misunderstanding at the beginning, this will be the format for all future videos.

Richard

[aaron5120]

It's clear now due to your latest explanation, thank you hhoforvolts.

Keep up your good work.

Aaron5120

[insAneTunA]

Well said.

[llewgnal]

That's still a very nice schematic you made for us, Thanx Thinking of useing #20 awg to wind new rods for the triple circut oil bath @ 200:200 turns after I figure out the circut for spining this little neospere ball magnet, not enough capacitors for one thing. Gary

[kcj1993]

BTW I never said or intended to imply that you don't know how to use a multimeter.

[kcj1993]

I feel special. I had a whole video made addressing my concerns . :)

I am new to your channel so I haven't seen many of your videos. I am losing the internet in 8 days so I hope your next video comes out soon.

[hhoforvolts]

Well everybody who takes interest in this project they are special to me. I have shot the raw footage for the new video, should upload by the middle of this coming week. This video wasn't targeting one person, just needed to have people find the answer to some questions themselves.

Richard