So trocar a correia, pois a correia fica resecada e acontece mesmo esse barulho, ja fiz varias manutenção neste aparelho, sou representate da PRECOR USA, aqui no brasil e vendo equipamento também.
Your drive belts are out of alignment or worn. For a temporary test. The the ribs with a spray lube. The noise will go away but will return when the lube is gone.
Wipe the belt ribs with a clean rag and adjust the flywheel angles.
Did you get this fixed? I have a 5.21 I just bought, It worked great the past 3 days and now when I just went to get on it , I hear a VERY similar sound. help!!!
I have the same problem on my 517i. Only not as noisey as yours. Mine is just a quiet squeeker almost like belt slipping on plastic making whining sound. Not a bearing. Probably dirt or maybe the plastic idler puller has developed fat small spots, I am going to examine closely. I am hestitant to spay silcone (or any lubricant on the belt & pulley) after learning that is the worst thing you can do to a parafin board treadmill.
I aggree that its belt noise....Clean the belt with a wire brush and then use some CANNING WAX... Found at your local super market...hope that works. it does for me
doesn't sound like a bearing to me man, sounds like either your primary or secondary drive belt is making all that noise....try spraying them with a silicon spry to see if that makes it go away, if so find out which belt and replace it....and call your local dealer for service.
Where did you get the bearings?
jasonxoc1 7 months ago
Bom amigo, muito facil de resolver esse problema.
So trocar a correia, pois a correia fica resecada e acontece mesmo esse barulho, ja fiz varias manutenção neste aparelho, sou representate da PRECOR USA, aqui no brasil e vendo equipamento também.
Trocou a correia acabou o problema.
um grade abraço amigo
fla2108 11 months ago
Your drive belts are out of alignment or worn. For a temporary test. The the ribs with a spray lube. The noise will go away but will return when the lube is gone.
Wipe the belt ribs with a clean rag and adjust the flywheel angles.
markpeterson. mindbites. com
knifetoenail 1 year ago
Did you get this fixed? I have a 5.21 I just bought, It worked great the past 3 days and now when I just went to get on it , I hear a VERY similar sound. help!!!
SurJones 1 year ago
Turns out it WAS the belt. If you have this "bleating" sound, a little belt dressing solves the problem.
I tore the machine apart and replaced bearings myself to no avail. Lots of work wasted. Only afterward did I try the belt dressing.
bryanska 2 years ago
yep- input bearings- hope it is warranty..
bubbabaloua 2 years ago
Hi, these noise are because the bearings are damage from the flywhell when are put the side arms, the center shaft.
NadaCal 2 years ago
I have the same problem on my 517i. Only not as noisey as yours. Mine is just a quiet squeeker almost like belt slipping on plastic making whining sound. Not a bearing. Probably dirt or maybe the plastic idler puller has developed fat small spots, I am going to examine closely. I am hestitant to spay silcone (or any lubricant on the belt & pulley) after learning that is the worst thing you can do to a parafin board treadmill.
Claudius2k 2 years ago
I aggree that its belt noise....Clean the belt with a wire brush and then use some CANNING WAX... Found at your local super market...hope that works. it does for me
RocNCo4U 3 years ago
doesn't sound like a bearing to me man, sounds like either your primary or secondary drive belt is making all that noise....try spraying them with a silicon spry to see if that makes it go away, if so find out which belt and replace it....and call your local dealer for service.
i'm a certified precor tech btw
key2287 5 years ago