Gearbox problems

[Gucio212121]

batery :)

[cccplt]

i hate when ppl put TM parts in shitty guns

[crowdsurfers]

get a new battery and a smart charger the stock batteries are usually more trouble than they are worth

[milsimaustralia]

so'd ya fix it?

[koreywhitley]

your gears might be shimmed to tightly and your motor cant spin the gears

[koreywhitley]

one that motor isnt the best and two you need a new spring on the selector switch

[herulf123]

yup i think your right

[njas6]

the brushes on the motor are worn down

[TheFatAssCat]

go fuck a squirrel

[TheFatAssCat]

let someone like your local or online airsof store fix it for you. dont mess with the eternals, its not easy

[randomaznkenny]

actually once you get used to it they are easy

[7subaru4]

The problem is your motor is not enought powerfull change your motor or upgrad for a 10.8V battery

[zanderwitaz]

if its your semi auto cut off lever,and this is a out of a g36 its supposed to wobble. thats because there is a plastic bracket on the outside that goes in with one of the gearbox screws and holds the spring that puts force on the semi auto cut off lever and forces it on the gear

[ACIDTOTAL]

sometimes happens this shit! :(

[drum00]

i dont mess arond that

[Jodid0]

I had the same problem, same solution: Bad shimming + wrong motor height. Now it works really well.

[EUMP]

how did you get it out - i need loads of help with this!

[AirsoftHawaii09]

Message me through my new account.

[Hotdogsex4]

did you solve the problem...It looks to me as if you shimed it wrong. When shimming you want to take out everything and do one gear at a time. Then putting them all in and seeing how freely they spin. after makeing adjustment you can go and put in everything else and you should gain your rof back. Oh and that peice that wobbles...it is suposed to make contact with the gear that pulls back the piston. Hopefully this helps.

[AirsoftHawaii09]

Yeah, I did fix it. The problem was both bad shimming and motor hight. Check out my new profile for the updated videos.

[mikogel]

okay it sounds like your battery may be too old how old is it?

[menter555]

thats a pos battery,ull going to need a 9.6 or a 8.4 2000+ to run it well

[Grasshopper257]

listen you do all these upgrades and yet you dont sound like an adult how old are you you have any experience? cause if id do all that stuff id fuck up my gun

[AirsoftHawaii09]

Thanks I think? I am 13 but I have been with airsoft guns when I was 11.

[muellr1369]

the reason your cut off lever is wobbleing is that you have lost your spring, you can buy a new one- it comes in a kit called "gearbox spring set."

the reason why you probably have the low "rpm," or "rate of fire" could be because youve upgraded your spring to a more powerful one.

[muellr1369]

also, for your wiring problem, try to get someone who you know is skilled with saudering and wiring electrical shit in general to help you. make sure if you have bought a new tapet plate (the plastic piece that connects to the air nozzel that the gears move back) make sure it's the right one for a version 3 gearbox because my friend accidentally put a version 2 tapet plate in my version 3 geearbox and my trigge would like every time i pulled it back. hope this helped you.

[airsofthawaii]

It mostly stocked parts! Its the original tappet plate.

[airsofthawaii]

No, the spring is in there and its a stocked spring..

[Shhadow74]

also you Really didnt need to switch the gearbox...

[airsofthawaii]

No, I switched the gearbox shell because I didnt know if it was a regular 6mm bushing compatable or a 6.2 gearbox. It came with my UTG paratrooper but says "CM.02" on it and looks like a CYMA gearbox? I may just have to go back to the old gearbox shell.

[Shhadow74]

Yeah dude dont keep shooting your gun it will strip the gears, and Chris is right your battery is probobly not powerful enough unless it has a 30 amp discharge, try to get a battery with a 30amp discharge.. but that will cost you a good like $40 atleast... also.. if you gonna plan on getting a bunch of upgrades just get a new gun dude seriously get a Echo1 and put those upgrades in it the gun will work a LOT better then it will on that AK47

[airsofthawaii]

I am getting a custom 9.6V 2000mah small type battery I designed to fit in my stock. I may be planing to get an Echo 1 M4A1 or and MP5 J.

[Shhadow74]

please do youl like it much more

[vietec]

Hey airsofthawaii, PM going your way.

[ChrisJuliano]

Forgot to say, your battery might not be powerfull enough to power that gearbox, And i wouldnt keep trying crap out you might strip the gears or ruin the motor :X

[airsofthawaii]

Well I have a stock spring in there. I think it might be my wireing/connections. I re-wired it with 18 guage wire but not a good soldering job. I may have to get a drop in gearbox and use this one for one of my other projects.

[ChrisJuliano]

Hmm, Post up on arniesairsoft Or airsoftforum

Im XxXChrisXxX on ASF and XxChrisxX on arnies, I personally dont know much but im sure others can help you, I know theres someone on there named airsofthawai i but im not sure if its you :)

Sorry i couldnt help

[airsofthawaii]

Yeah, I am airsofthawaii on ArniesAirsoft and Airsoftforum. =] I posted this for vietec on ASF. Thanks though chris and thanks for looking.