We run Honda BF225 and Twin BF90 on our three commercial ribs. We roll over every three years with thousands of hours on the clock. we have never had a problem -EVER- and Honda have been nothing but helpful even supplying ECU upgrades to a perfectly running engine! To date we have had 9 engines without a problem.
We service them as per the maintainance schedule (We change the fuel pre filter every 50 hours)
I find some of these posts absolutely hilarious. Honda is the largest engine manufacturer IN THE WORLD. You're telling me they designed a product with parts that will rust under normal operating conditions? No... if they're rusting that means water is not supposed to be in there. If water is getting in there, that means it was installed incorrectly, the case was incorrectly seated, or the owner has neglected it. Blame yourself of your under-paid installer for this problem pal.
These screws are typical steel highly anodized screws found in Japanese cars for decades. They dont get get rusty under normal automotive applications even after many years. But the sea corrosive enviroment demands special inox screws just as the USA manufacturers use to all their relevant products. Unfortunately the condition you describe is due to cheap Japanese solutions rather than a product misuse according to my humble opinion. Too bad for a Honda motor which should stand for quality .
I work for honda your caling was not closed properly or not riged properly(6to8inchs), also the water injestion is covered by honda service bulletin #56.but your a know it all honda basher. next time buy a jet ski
This took place after 30 days, It was serviced by the Honda dealer. What is it you think I should have done? Can you cite the page number of the owners manual? You have no clue. Honda makes poor produces and does not support the customer. Get your fact straight.
All comes down to maintenance. This will happen to all marine engines if not maintained properly. None of the Honda outboards I look after suffer from these problems unless the tightass owners neglect to maintain them. This guy got what he deserves, then he has the nerve to condemn Honda for his neglect. Cock!!
I am well aware of the height specifications for V6 installation. The problems associated are water entry into the lower cylinders and contamination of the oxy sensor, NOT external corrosion. The engine may have been installed incorrectly, or the operator may not have noticed the motor submarine diving in the ocean, But this is an installer issue, not a design floor.The whole point is, dont blame the engine manufacturer for such an obvious screw up by either the Installer, the operator or both!!
Yes they suck salt water in through the exhaust. When they rigged my motor they allowed eight inches from the water line to the exhaust. That has changed to twelve inches. Honda has told me too bad we can change the specs anytime.
I have a BF 130 Honda runs great never misses a beat BUT the same cheap ass parts are showing signs of rust. I spray them with WD spray but it is not going to stop the problem.
Stupid of honda to tarnish their name over what you would think would be $50 max in SS parts.??
Right they saved a few dollars up front. After seeing my Honda rusting out a fishing friend is going to repower with an other brand. Honda just lost a twin motor sale. I tell everyone I can about this, Do Not Buy Honda.
I know others with this motor that are satisfied with it. Are you the only one having problems? The motor appears as if it has been exposed to salt water under the cowling. So, since you last posted here, are there any new developments you can share? Thanks for any info.
We run Honda BF225 and Twin BF90 on our three commercial ribs. We roll over every three years with thousands of hours on the clock. we have never had a problem -EVER- and Honda have been nothing but helpful even supplying ECU upgrades to a perfectly running engine! To date we have had 9 engines without a problem.
We service them as per the maintainance schedule (We change the fuel pre filter every 50 hours)
jwfrary 1 year ago
I find some of these posts absolutely hilarious. Honda is the largest engine manufacturer IN THE WORLD. You're telling me they designed a product with parts that will rust under normal operating conditions? No... if they're rusting that means water is not supposed to be in there. If water is getting in there, that means it was installed incorrectly, the case was incorrectly seated, or the owner has neglected it. Blame yourself of your under-paid installer for this problem pal.
patontree 1 year ago
i have the Honda BF 225 for about 3 years and it still looks like new i have never any problems with it
454chevy454 1 year ago
These screws are typical steel highly anodized screws found in Japanese cars for decades. They dont get get rusty under normal automotive applications even after many years. But the sea corrosive enviroment demands special inox screws just as the USA manufacturers use to all their relevant products. Unfortunately the condition you describe is due to cheap Japanese solutions rather than a product misuse according to my humble opinion. Too bad for a Honda motor which should stand for quality .
billias1gr 2 years ago
I work for honda your caling was not closed properly or not riged properly(6to8inchs), also the water injestion is covered by honda service bulletin #56.but your a know it all honda basher. next time buy a jet ski
terkey420 2 years ago
next time take better care of the outboard,
1blackpaper 2 years ago
This took place after 30 days, It was serviced by the Honda dealer. What is it you think I should have done? Can you cite the page number of the owners manual? You have no clue. Honda makes poor produces and does not support the customer. Get your fact straight.
freewheeln2006x 2 years ago
Comment removed
smoolynmj 3 years ago
All comes down to maintenance. This will happen to all marine engines if not maintained properly. None of the Honda outboards I look after suffer from these problems unless the tightass owners neglect to maintain them. This guy got what he deserves, then he has the nerve to condemn Honda for his neglect. Cock!!
recommit 3 years ago
In fact the problem with this Honda happen with-in 30 days of the motor being rigged.
Stalling from (salt) water entering the motor is a know problem. You should get your facts straight before you post.
Now of course, we know what you are!!
freewheeln2006x 3 years ago
I am well aware of the height specifications for V6 installation. The problems associated are water entry into the lower cylinders and contamination of the oxy sensor, NOT external corrosion. The engine may have been installed incorrectly, or the operator may not have noticed the motor submarine diving in the ocean, But this is an installer issue, not a design floor.The whole point is, dont blame the engine manufacturer for such an obvious screw up by either the Installer, the operator or both!!
recommit 3 years ago
should have bought a optimax
missjo69 4 years ago
I've been told that the Evinrude E-tech would have been better as well. At it point oars would have been better.
freewheeln2006x 4 years ago
Omg Honda sux man...
Nice movie btw
good luck
Andreas900 4 years ago
Yes they suck salt water in through the exhaust. When they rigged my motor they allowed eight inches from the water line to the exhaust. That has changed to twelve inches. Honda has told me too bad we can change the specs anytime.
freewheeln2006x 4 years ago
I have a BF 130 Honda runs great never misses a beat BUT the same cheap ass parts are showing signs of rust. I spray them with WD spray but it is not going to stop the problem.
Stupid of honda to tarnish their name over what you would think would be $50 max in SS parts.??
maximustwoten 4 years ago
Right they saved a few dollars up front. After seeing my Honda rusting out a fishing friend is going to repower with an other brand. Honda just lost a twin motor sale. I tell everyone I can about this, Do Not Buy Honda.
freewheeln2006x 4 years ago
I know others with this motor that are satisfied with it. Are you the only one having problems? The motor appears as if it has been exposed to salt water under the cowling. So, since you last posted here, are there any new developments you can share? Thanks for any info.
SharkBoat 4 years ago
what kinda money are they trying to rob you for the replacement parts?
KartMan250 4 years ago
should have bought a merc or a yamaha
KartMan250 4 years ago
It's too late for me but I hope other can learn from my mistake.
freewheeln2006x 4 years ago
What was the original cost of this motor? It looks like a very
poor quality item. THIS is a HONDA product?
coopcruizer 5 years ago
FAKE FAKE FAKE FAKE de mierda owned
SoNy18DesigN 4 years ago
Please do not drink so much sangria before posting. It's real real real no BS of any kind.
freewheeln2006x 4 years ago
Honda Marine engine is damaged. What does Honda plan to do
for the customer?
coopcruizer 5 years ago
Honda claims all problems are do to an "Application Issue" In other words I made the mistake of thinking I could put a Honda Marine Motor on a boat!
freewheeln2006x 4 years ago