Hola, me podrias decir como hiciste el piston? Llevo semanas buscando donde comprar uno o como hacerlo para hacer un motor stirling como el tuyo y nadamas no encuentro algo que me funcione, gracias.
Hola, me podrias decir como hiciste el piston? Llevo semanas buscando donde comprar uno o como hacerlo para hacer un motor stirling como el tuyo y nadamas no encuentro algo que me funcione, gracias.
@avd88 Hola.El piston está realizado en bronce. Si no tienes un torno te va a ser dificil hacer este motor pues es muuuy delicado de ajustar. De hecho para mi es un tema pendiente, y aun no he logrado que funcione como quiero.El material es una barra solida de bronce (se compra en distribuidores industriales) Buscar en tu ciudad talleres y preguntarles donde compran ellos material. El piston se tornea, y se le deja con unas paredes finas para que pese poco, y se pule por fuera con acabado espejo
Hola, me gustaría saber si pudiste mejorar este modelo y que materiales utilizaste. Hice otros sitirlings y todos funcionaron bien, salvo este modelo que no puedo hacerlo andar. En youtube podes verlos buscando por "horacioraul". Gracias.
Enhorabuena, viendolo se me ocurre una mejora: divide la lana de acero en 2 partes, 1/3 más hacia el principio del tubo en el mismo punto de la llama y 2/3 con 2-3 cm de separación.
Muchas gracias 4NTU4N, intentaré probar lo que me dices. Tambien intentaré arreglar la holgura que presenta el piston y la biela, y que genera el ruido que se escucha, quizas ayude. Ademas lo montaré en una base mas solida aun. Un saludo!
@dgalvarez im in a similar sittuation my prototype runs and runs well but not very high rpm but i think i know how to increase it , IF you tune the engine to run without a flywheel untill you get high speed oscillations you then need to measure its stroke and set your flywheel cam to match also use a light flywheel this should then get the flywheel to run at the oscillation speed , i will be testing this next , I also used a graphite piston on a glass liner which has alot less drag
so what is its out put, what is it ment to do?
oli4814 3 months ago
How the displacer is made?
Mons1990 3 months ago
what is the foil inside the cylinder?
badabarian 9 months ago
This has been flagged as spam show
Hola, me podrias decir como hiciste el piston? Llevo semanas buscando donde comprar uno o como hacerlo para hacer un motor stirling como el tuyo y nadamas no encuentro algo que me funcione, gracias.
avd88 10 months ago
Hola, me podrias decir como hiciste el piston? Llevo semanas buscando donde comprar uno o como hacerlo para hacer un motor stirling como el tuyo y nadamas no encuentro algo que me funcione, gracias.
avd88 10 months ago
@avd88 Hola.El piston está realizado en bronce. Si no tienes un torno te va a ser dificil hacer este motor pues es muuuy delicado de ajustar. De hecho para mi es un tema pendiente, y aun no he logrado que funcione como quiero.El material es una barra solida de bronce (se compra en distribuidores industriales) Buscar en tu ciudad talleres y preguntarles donde compran ellos material. El piston se tornea, y se le deja con unas paredes finas para que pese poco, y se pule por fuera con acabado espejo
dgalvarez 10 months ago
what is the fluid u have used inside the cylinder??
parimalthirteen 10 months ago
@parimalthirteen Fluid?? It's hot air
dgalvarez 10 months ago
Alvarez Jr...what ever you do, DON'T BURN THE HOUSE DOWN....LOL
t2t3456 1 year ago
@t2t3456
hahaha don´t worry. All was under control!! :D
dgalvarez 1 year ago
try making the flywheel out of a reader whell out of a vcr
ace7279ify 1 year ago
@ace7279ify Thanks for the suggestion
dgalvarez 10 months ago
what the purpose of this machine
ThePioneerPyro 1 year ago
@ThePioneerPyro Sorry, it only serves to experiment.
dgalvarez 10 months ago
Hola, me gustaría saber si pudiste mejorar este modelo y que materiales utilizaste. Hice otros sitirlings y todos funcionaron bien, salvo este modelo que no puedo hacerlo andar. En youtube podes verlos buscando por "horacioraul". Gracias.
horacioraul 2 years ago
how much did the brass for the piston cost
Joeyad4 2 years ago
One rod of brass may cost 50 euro. But you can build arround 45 pistons. Because each rod measures 900mm (in my case)
dgalvarez 2 years ago
what did you use as a piston and how did you make it? and how much does the flywheel weigh? thanks for the help.
anthacdc 2 years ago
The piston was made of brass, and I think that the flywheel is too heavy. I dont know the weigh exactly
dgalvarez 2 years ago
Enhorabuena, viendolo se me ocurre una mejora: divide la lana de acero en 2 partes, 1/3 más hacia el principio del tubo en el mismo punto de la llama y 2/3 con 2-3 cm de separación.
4NTU4N 2 years ago
Muchas gracias 4NTU4N, intentaré probar lo que me dices. Tambien intentaré arreglar la holgura que presenta el piston y la biela, y que genera el ruido que se escucha, quizas ayude. Ademas lo montaré en una base mas solida aun. Un saludo!
dgalvarez 2 years ago
very cool thermoacoustic motor...
SWINGREGORY 2 years ago
Thanks SWINGREGORY ,
Its is only a prototype, i think that it is very inefficient, so i must to improve it. have you got any idea to increase the rpm?
dgalvarez 2 years ago
decrease some weight of the flywheel..use bearings...
neem2345 1 year ago
@dgalvarez im in a similar sittuation my prototype runs and runs well but not very high rpm but i think i know how to increase it , IF you tune the engine to run without a flywheel untill you get high speed oscillations you then need to measure its stroke and set your flywheel cam to match also use a light flywheel this should then get the flywheel to run at the oscillation speed , i will be testing this next , I also used a graphite piston on a glass liner which has alot less drag
mimic58 1 year ago