Tamiya TT 01 EzRun Brushless 9T 4300kv 35A ESC - HIGH - Speed Runs - over 60mph - pt1

[badboylowrider006]

Bro I watch ur video everyday at work on break at the house everywhere u inspired me . But I need help wit this project

[GODnSPEED]

@badboylowrider006

* * *THANK YOU FOR CONSIDERING THIS VIDEO* * *

as an inspiration for your project! I am GRATEFUL, my FRIEND!

If you use the same setup as mine, you should get the same results:

Even if you don't upgrade the capacitor or add 2extra fans, you can still

(((adjust your ESC))) so it doesn't over heat, and still reach over 50mph,

with the same gear settings I use.

[badboylowrider006]

Bec or capacitor

[badboylowrider006]

So I will need a bec to even run my car for starter

[GODnSPEED]

@badboylowrider006

"NO"

you don't have to buy one...........but you will need to buy a (higher volt ) fan from HOBBYPARTZ

that can take more than 5v,

if you will use a 11.1volt 3 CELL LIPO,

because the stock fans are 5-7volts

Or you can (unplug) the stock fan and re-wire it to plug into your receiver to get (safe) power.

[badboylowrider006]

R u running a bec

[GODnSPEED]

@badboylowrider006

I bought a bec from HobbyPartz, but did not install it on the system.

$18.00

UBEC-5A-HV High Voltage 07E32-ExceedRC_UBEC-5A-V1 Ultimate BEC

I did witch the original capacitor with a bigger one, that helps

the ESC from overheating, or blowing the smaller capacitor.

[badboylowrider006]

Hey godnspeed ur video is killing it but I have a tt01e and can u do a how to video on ur setup and I also have the flysky fs-gt3b transmitter and receiver how do I setup that up Iam new to the RC world hit me up THANK

[GODnSPEED]

@badboylowrider006

HEY FRIEND!

Thanks for viewing and asking questions.

If I can get some time off, I can make a vid of how I setup my system...

You can learn how to bind your transmitter on YouTube, search.....

FlySky FS-GT3B 2.4ghz 3ch transmitter

fast forward to (9:20 seconds)

[CRINKLETOES12]

nice vid plz could someone tell me the difference between a tto1 tto1e tto1d etc because i dont know thnx

[GODnSPEED]

@CRINKLETOES12

Each letter means that the chassis are made differently:

TT01E

wheelsacademy. com/ a1/ rcauto/ Tamiya/ electro/ chassis/ tt-01e. JPG

TT01D

s10.mx3g. com/ day_080525/ 20080525_a56b2d7d5bfe1f9b5c8eR­6gWqo2OJQZ3.jpg

(copy each link and remove the spaces to see the picture)

[GODnSPEED]

@CRINKLETOES12

I SUB 2 U MY FRIEND!

[jkflorida2013]

I had a mamba setup in a tc3 doing 91.7 mph. I almost broke my ankle a few times!

[GODnSPEED]

@jkflorida2013

LOL!

DON'T END UP IN A WHEELCHAIR DUDE!

I SUBBED 2 U !

[opelmadness]

Sweet speeds! I got a TT-01 and the same ez-run kit for my traxxas slash. Gonna put it in the TT.

What battery did you use and what was the tire diameter? Thinking of trying some speed runs...

Thanks, Thomas, Sweden.

[GODnSPEED]

@opelmadness * 4000mah 3 cell 40-80C lipo battery ____make sure it's a high C rate battery ____change bottom battery screws to longer ones YOU WILL HAVE TO EXPERIMENT with your esc: timing & punch, also your pinion & spur gears. Pleas protect your esc from burning up! As for the tire size: Name: Wheel +Rubber Tires Diameter: 67mm Width: 26.5mm Hexagonal joints: 12 mm I bought them off eBay search (1:10 On Road Wheel) I found 4 for $10 (USA) But you can get 2 for $3.95 (hong kong)

[opelmadness]

@GODnSPEED

Thanks! Unfortunately I only have a 2 cell LiPo, but the rest is more or less similar.

Rubber tires and ultra lightweight rims.

Going to try to reach at least 50 mph. :)

I'll post it if (or when) i get it.

[GODnSPEED]

@opelmadness

You can reach the 50s!

I normally reach the 50's on 2S lipo 40C - 80C max Burst

I buy my lipos from HobbyPartz (Sky Lipo)

They have good quality and will save you money!

[GODnSPEED]

@opelmadness

I just Subbed 2 U !

[Rctamiyatt01]

Great cheers for the spec you use. Can you elaborate on the rock blocker? Thanks.

[GODnSPEED]

@Rctamiyatt01

I'm thinking about selling it as a kit, but I can tell you something else that works:

You can make a metal (skid plate) that is shaped like the bottom of the chassis and screw it on!

Many people still do that and certain chassis have a skid plate that you can buy too.

Doing it yourself may be cheaper!

[GODnSPEED]

*

*

*

I ADDED MY PARTS - LIST IN THE DESCRIPTION, ABOVE !

*

*

*

[Rctamiyatt01]

Impressive speed run. Im hoping to run these speeds soon.

[GODnSPEED]

@Rctamiyatt01

Hey Friend.

Always make sure your area is clear before you run your car!

1. Avoid bumpy streets

2. Avoid high traffic streets

3. Avoid parking lots with poles near your straight-away

4. Find a street with grass on both sides (in case you go off road)

5. If you don't feel comfortable about your next run, always wait

If you use the exact same setup as other people's videos...you should get close to the same speeds,

but it also depends on your ESC settings too!